User's Manual

ManualsBrandsCrow Electronic Engineering ManualsElectronicsDECT ULE transceiver

DECT ULE-TMP

TEMPERATURE DETECTOR

CR-DU-TMP EURO

CR-DU-TMP USA

ELECTRONIC ENGINEERING LTD.

INSTALLATION INSTRUCTIONS

P/N 7105195REV. B (O.Z.)

Issue Date: July 6

, 2015

INTRODUCTION

This DECT ULE TMP detector is an advanced, fully

supervised low-current wireless detector that

includes a DECT ULE transceiver for reliable

system operation.

A dedicated cable is supplied with this device.

This DECT ULE TMP uses smart message control,

which verifies that all messages are successfully

transmitted, so that no event will be uninformed to

the system.

This DECT ULE TMP detector includes series of

messages for full communication administration

(Keep Alive, Tamper Status, Battery Status, Alert,

Configuration, etc.) as well as test transmission

signals.

FEATURES

 DECT ULE RF protocol.

 Low current Technology.

 Powered by a single 3V Lithium battery.

 Battery life: up to 4 years.

 Frequency Band: All DECT Standard Bands.

 Tamper Open/Close transmission.

 Temperature reporting transmissions.

 Keep Alive transmission.

 Battery status transmission.

 Bi-Color LED indications for monitoring &

Pairing.

 Range up to 500m on open space.

 Back tamper.

 2 sensors – Internal & External (optional).

 Remotely configurable.

 Friendly Pairing and Installation processes.

OPERATION

The DECT ULE TMP detector transmits the

following events data:

KEEP ALIVE – A periodical transmission

indicating detector’s presence. The time interval is

configurable – the minimum value is 3 seconds.

ALARM – Indicating that measured Temperature

is out of defined Low / High thresholds. The Red

LED will blink once.

Temperature Monitoring – A periodic

transmission (configurable) indicating the

measured Internal or External temperature.

LOW BAT – A transmission indicating the battery

reached a pre-set low level (~2.5V). When Battery

level drops below Cut Off level (~2.3V) the device

will stop functioning and the Red LED will

constantly light On.

TAMPER – Whenever the cover is removed from

Bracket or the device is tear off from the wall, a

message will be transmitted with “Tamper ON”

signal. When cover will be returned a “Tamper

OFF” signal will be transmitted.

PREPARE THE DEVICE FOR

INSTALLATION

1. Open the screw cover and unscrew the holding

screw as shown in Figure 1.

2. Separate the device from the Bracket by tilting

the front cover as shown in Figure 1.

3. Break one piece of the Bracket corners

according to the device installation orientation

(Horizontal/Vertical) as shown in Figure 2.

4. Genteelly connect the External Temperature

sensor cable to its location as shown in Figure

4. Be aware that the connector can be inserted

in only one direction.

5. Continue with the pairing process.

FIGURE 1 – SEPARATE FROM BRACKET

FIGURE 2 – DEVICE ORIENTATION

FIGURE 3 – INSTALL THE CABLE

PAIRING PROCESS

1. Place a battery as instructed in Figure 4 and wait

until the Red LED stops blinking.

2. Initiate the Base Station pairing process.

3. Initiate the device pairing process by pressing the

pairing button for 5 seconds – the pairing button

is shown in Figure 5. The Green LED will

constantly turn On. When the Green LED starts

blinking release the pairing button.

4. The device should register to the Base Station.

5. When registration process is successfully

completed the Green LED will constantly light On

for 3 seconds and then turn off.

6. If registration process failed the Red LED will

blink (remove the battery and run the pairing

process again).

FIGURE 4 – BATTERY INSERTION

FIGURE 5 – PAIRING BUTTON

SELECT MOUNTING LOCATION

It is recommended to mount the device vertically on

a flat area to get maximum range.

As the detector is a wireless transceiver, and in

order to take full advantage of its sophisticated

operation, do not install the detector in areas where

large metal objects could interfere with the

transmission of signals.

TRANSMISSION TESTS

Tamper transmission test –

Changing the tamper switch state (by attaching /

removing the device to / from the Bracket) will

cause tamper transmissions. Verify receiving the

indication on your Application / Base Station.

Identification transmission test –

Use your Application / Base Station and send

Identification Request to the device. The device

will start blinking the Green & Red LEDs

alternately – 5 times each LED starting with the

Green LED.

Horizontal

Installation

Vertical

Installation

Summary of content (2 pages)

PAGE 1
2 DECT ULE-TMP TEMPERATURE DETECTOR CR-DU-TMP EURO CR-DU-TMP USA ELECTRONIC ENGINEERING LTD. INTRODUCTION 3 FEATURES This DECT ULE TMP uses smart message control, which verifies that all messages are successfully transmitted, so that no event will be uninformed to the system.           This DECT ULE TMP detector includes series of messages for full communication administration (Keep Alive, Tamper Status, Battery Status, Alert, Configuration, etc.) as well as test transmission signals.
PAGE 2
13 14 FIGURE 6 – MOUNTING THE DEVIC MOUNTING THE DETECTOR 15 FIGURE 7 – MOUNTING THE SENSOR 1. Separate the device from its bracket by unscrewing the holding screw and tilting the front cover as shown in Figure 1. 2. Mount the Bracket to the surface by using the adhesive tape strip or by using the 3 screws as shown in Figure 6. If using the screws, make sure to tighten the tamper screw - the middle screw. 3. Perform the Pairing process as described above in this document. 4.