User's Manual

13
14
15
FIGURE 6 - DETECTION PATERN
TRANSMISSION TESTS
Tamper transmission test –
Changing the tamper switch state (by attaching /
removing the device to / from the Bracket) will
cause tamper transmissions. Verify receiving the
indication on your Application / Base Station.
Motion transmission test –
Waving hands or moving in front of the detector
from one side to the other will cause Motion alert
transmissions. Verify receiving the indication on
your Application / Base Station. Pay attention that
due to APS feature it is required waiting 2 minutes
between 2 consecutive indications.
Identification transmission test –
Use your Application / Base Station and send
Identification Request to the device. The device
will start blinking the Green & Red LEDs
alternately – 5 times each LED starting with the
Green LED.
BATTERY REPLACEMENT
1. Open the screw cover and unscrew the holding
screw as shown in Figure 1.
2. Separate the device from the Bracket by tilting
the front cover as shown in Figure 2.
3. Remove the in use battery from the device using
the Red strip.
4. Return the Red strip to its location inside the
battery holder and install the new battery in the
correct polarity marking on the Red strip – as
shown in Figure 3.
5. Wait until the Red LED stops blinking.
6. In case the device was paired to a Base Station
the device should automatically register again to
the same Base Station.
7. Place the device in the Bracket by inserting it
back into appropriate position and validate
receiving the Tamper Alert Off indication on your
Application / Base Station.
8. Fasten the holding screw and close the screw
cover.
16
17
18
APS – AUTOMATIC POWER SAVE
After the device will transmit Alarm On message a
Hold Off Time prior will be started during which no
additional Alarm transmission will be initiated.
When the Hold Off Time prior will be elapsed the
device will transmit Alarm Off message. Setting
the Hold Off Mode to RETRIGGER will increase
the Hold Off Time and will save more Battery.
FCC & IC STATEMENT
FCC ID: NFC-CRDU
IC: 8164A-CRDU
This device complies with FCC Rules Part 15 and with
Industry Canada license-exempt RSS standard(s).
Operation is subject to two conditions: (1) This device
may not cause harmful interference, and (2) this device
must accept any interference that may be received or
that may cause undesired operation.
Canada: Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en
compromettre le fonctionnement.
WARNING:
Changes or modifications to this equipment not
expressly approved by the party responsible for
compliance (Crow Electronic Engineering Ltd.) could
void the user’s authority to operate the equipment.
FCC & IC STATEMENT (Continue)
Note: The digital circuit of this device has been tested
and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV
technician for help.
19
20
21
REGULATORY APPROVALS
This DECT ULE PIR detector conforms to the essential
requirements set out by:
 RTTE directive:1999/5/EC
 EMC directive: 2004/108/EC
 Low Voltage directive: 2006/95/EC
 RoHS directive: 2011/65/EU
Harmonized Standards applicable to this products are:
 EN301406
 EN301489-6
 EN301489-1
 EN61000-6-3
 EN60950-1
 EN50581
 UL639
 ULC-S306-03
TECHNICAL SPECIFICATIONS
RF Protocol DECT ULE
Modulation Type GFSK
Frequency 1880–1900 MHz - Europe
1920–1930 MHz - USA/Canada
Event Transmission Alarm, Tamper, Keep Alive,
Batery status.
Detection Method Infra-Red
Range in open space >500m
Battery Lithium. 3V Type: CR123A
Size: 2/3A
Battery life 4 years @ APS mode
Current Consumptions:
Standby 11A
Average 26µA
Maximum (TX) 250mA
Low Battery 2.5VDC
Cut Off Battery 2.3VDC
Transmit Power (Typ.): 23dBm (EURO), 20dBm (USA)
Tamper Switch Back Tamper
Operating temperature -10C to +55C
Dimensions 113mm x 61mm x 38mm
Weight 95 gr.
Weight (inc. battery) 110 gr.
CAUTION !!!
RISK OF EXPLOSION IF BATTERY IS
REPLACED BY DIFFERENT TYPE / MODEL.
DISPOSE USED BATTERIES
ACCORDING TO ITS INSTRUCTIONS
ATTENTION !!!
RISQUE D'EXPLOSION SI LA PILE EST
REMPLACÉE PAR UN TYPE INCORRECT.
22
23
CROW ELECTRONIC ENGINEERING LTD. ("Crow") - WARRANTY POLICY CERTIFICATE
This Warranty Certificate is given in favor of the purchaser (hereunder the "Purchaser") purchasing the products directly from Crow or from its
authorized distributor.
Crow warrants these products to be free from defects in materials and workmanship under normal use and service for a period of 24 months from the
last day of the week and year whose numbers are printed on the printed circuit board inside these products (hereunder the "Warranty Period").
Subject to the provisions of this Warranty Certificate, during the Warranty Period, Crow undertakes, at its sole discretion and subject to Crow's
procedures, as such procedures are form time to time, to repair or replace, free of charge for materials and/or labor, products proved to be defective
in materials or workmanship under normal use and service. Repaired products shall be warranted for the remainder of the original Warranty Period.
All transportation costs and in-transit risk of loss or damage related, directly or indirectly, to products returned to Crow for repair or replacement shall
be borne solely by the Purchaser.
Crow's warranty under this Warranty Certificate does not cover products that is defective (or shall become defective) due to: (a) alteration of the
products (or any part thereof) by anyone other than Crow; (b) accident, abuse, negligence, or improper maintenance; (c) failure caused by a product
which Crow did not provide; (d) failure caused by software or hardware which Crow did not provide; (e) use or storage other than in accordance with
Crow’s specified operating and storage instructions.
There are no warranties, expressed or implied, of merchantability or fitness of the products for a particular purpose or otherwise, which extend
beyond the description on the face hereof.
This limited Warranty Certificate is the Purchaser's sole and exclusive remedy against Crow and Crow's sole and exclusive liability toward the
Purchaser in connection with the products, including without limitation - for defects or malfunctions of the products. This Warranty Certificate
replaces all other warranties and liabilities, whether oral, written, (non-mandatory) statutory, contractual, in tort or otherwise.
In no case shall Crow be liable to anyone for any consequential or incidental damages (inclusive of loss of profit, and whether occasioned by
negligence of the Crow or any third party on its behalf) for breach of this or any other warranty, expressed or implied, or upon any other basis of
liability whatsoever. Crow does not represent that these products can not be compromised or circumvented; that these products will prevent any
person injury or property loss or damage by burglary, robbery, fire or otherwise; or that these products will in all cases provide adequate warning or
protection.
Purchaser understands that a properly installed and maintained product may in some cases reduce the risk of burglary, fire, robbery or other events
occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property
loss or damage as a result.
Consequently, Crow shall have no liability for any personal injury; property damage or any other loss based on claim that these products failed to
give any warning.
If Crow is held liable, whether directly or indirectly, for any loss or damage with regards to these products, regardless of cause or origin, Crow’s
maximum liability shall not in any case exceed the purchase price of these products, which shall be the complete and exclusive remedy against
Crow.
CROW ELECTRONIC
ENGINEERING LTD.
12 Kineret St.
Airport City, 70100 Israel
Tel. [phone]
Fax. [phone]
[e-mail]
[e-mail]
www.thecrowgroup.com
CROW LATIN AMERICA USA INC.
7200 NW 19 st.
Suite 307
Miami FI 33126, USA
Tel. [phone]
Fax. [phone]
[e-mail]
www.crowlatinamerica.com
The battery must be
replaced by 3V Lithium
battery Size 2/3A
Models such as:
1. VARTA CR123A
2. GP CR123A