User's Manual

ManualsBrandsCrow Electronic Engineering ManualsElectronicsDECT ULE transceiver

DECT ULE-PIR S

WIRELESS PIR DETECTOR

CR-DUS-PIR-EU

CR-DUS-PIR-USA

ELECTRONIC ENGINEERING LTD.

INSTALLATION INSTRUCTIONS

P/N 7101107 REV. B (O.Z.)

Issue Date: July 6

, 2015

INTRODUCTION

This DECT ULE S PIR detector is an advanced,

fully supervised low-current wireless detector that

includes a DECT ULE transceiver for reliable

system operation.

This DECT ULE S PIR detector includes APS

mechanism for extending the battery lives (see

below to learn more).

This DECT ULE S PIR detector includes series of

messages for full communication administration

(Keep Alive, Tamper Status, Battery Status, Alert,

Configuration, etc.) as well as test transmission

signals.

This product require professional installation in

accordance with UL 681.

FEATURES

 DECT ULE RF protocol.

 Low current Technology.

 Powered by a single 3V Lithium battery.

 Battery life: up to 4 years.

 Frequency Band: All DECT Standard Bands.

 Tamper Open/Close transmission.

 Keep Alive transmission.

 Battery status transmission.

 Bi-Color LED indications for monitoring &

Pairing.

 Range up to 500m on open space.

 Back Tamper.

 Remotely configurable.

 Motion Detection up to 12m.

 Friendly Pairing and Installation processes.

OPERATION

This DECT ULE S PIR detector transmits the

following events data:

KEEP ALIVE – A periodical transmission indicating

detector’s presence. The time interval is

configurable – the minimum value is 1 minute.

ALARM – Alarm transmission triggered by the

device indicating Motion detection. The Red LED

will blink once.

LOW BAT – Whenever the battery reaches a pre-

set low level (~2.5V), a Battery Low signal will be

sent. When Battery level drops below Cut Off level

(~2.3V) the device will stop functioning and the Red

LED will be constantly lighted On.

TAMPER – Whenever the cover is removed from

Bracket or the device is tear off from the wall, a

message will be transmitted with “Tamper ON”

signal. When cover will be returned a “Tamper

OFF” signal will be transmitted.

FIGURE 1 – SEPARATE FROM BRACKET

FIGURE 2 – SEPARATE FROM BRACKET

FIGURE 3 - BATTERY PLACEMENT

PAIRING PROCESS

1. Open the screw cover as shown in Figure 1.

2. Unscrew the holding screw and eparate the

device from the Bracket by tilting the front cover

as shown in Figure 2.

3. Place a battery as instructed in Figure 3 and

wait until the Red LED stops blinking.

4. Initiate the Base Station paring process.

5. Initiate the PIR pairing process by pressing the

pairing button for 5 seconds – the pairing button

is shown in Figure 4. The Green LED will

constantly turn On. When the Green LED starts

blinking release the pairing button.

6. The device should register to the Base Station.

7. When registration process is successfully

completed the Green LED will constantly light

On for 3 seconds and then turn Off.

8. If registration process failed the Red LED will

blink (remove the battery and run the pairing

process again).

FIGURE 4 - PAIRING

SELECT MOUNTING LOCATION

Choose a location most likely to intercept an

intruder. (Our recommendation is a corner

installation). See Figure 6 - Detection Pattern. The

detector is more sensitive detecting motion

crossing the space in front of the detector then

moving toward the detector.

Recommended mounting height – 1.9m-2.3m.

Avoid the following locations:

 Facing direct sunlight.

 Facing areas that may change temperature

rapidly.

 Areas where there are air ducts or substantial

airflows.

This device detect or performs better when

provided with a constant and stable environment.

MOUNTING THE DETECTOR

1. Open the screw cover as shown in Figure 1.

2. Unscrew the holding screw and eparate the

device from the Bracket by tilting the front

cover as shown in Figure 2.

3. Mount the Bracket to the wall: place 3 screws

and make sure you tighten the tamper screw -

the middle screw.

4. For flat mounting on a wall use the middle 3

screws location as shown in Figure 5. For

mounting in a 45 degrees position, use the 3

screws locations on the bracket’s sides.

5. Place a battery as instructed in Figure 3 and

wait until the Red LED stops blinking.

6. Initiate the Pairing process.

7. Place the device in the Bracket by inserting it

back into appropriate position.

8. Fasten holding screw and close screw cover.

Note: The Detector can be mounted to a Wall/Celling

using an optional Wall/Celling Mount Bracket or

Adhesive Tapes – for more details see Crow P/N

7104107 REV. A.

FIGURE 5 - INSTALLATION

Summary of content (2 pages)

PAGE 1
2 DECT ULE-PIR S WIRELESS PIR DETECTOR CR-DUS-PIR-EU CR-DUS-PIR-USA ELECTRONIC ENGINEERING LTD. INTRODUCTION 3 FEATURES This DECT ULE S PIR detector is an advanced, fully supervised low-current wireless detector that includes a DECT ULE transceiver for reliable system operation. This DECT ULE S PIR detector includes APS mechanism for extending the battery lives (see below to learn more).
PAGE 2
13 14 FIGURE 6 - DETECTION PATERN 15 TRANSMISSION TESTS BATTERY REPLACEMENT Tamper transmission test – Changing the tamper switch state (by attaching / removing the device to / from the Bracket) will cause tamper transmissions. Verify receiving the indication on your Application / Base Station. 1. 2. Motion transmission test – Waving hands or moving in front of the detector from one side to the other will cause Motion alert transmissions.