User's Manual

13 14 15
MOUNTING THE DETECTOR
1. To remove the front cover, unscrew the
holding screw, insert a flat screwdriver in the
slot between the front and the bottom while
pushing and twisting it gently until the front
cover is disengaged. (Fig. 1)
2. Mount the detector base: place all 3 screws
and make sure you tighten the tamper screw
(the middle screw) easily, so the back tamper
switch will press the switch successfully when
PCB is placed back - over winding may result
in false mechanical adaptation and lack of
tamper press.
3. Mount the Magnet Unit near the Marking.
4. Place the CR123A BAT according to the right
polarity
5. Place the cover by inserting it back in the
appropriate closing pin and screw the holding
screw.
INSTALLATION
Opening Direction Axis:
X-Y or X-Z
ALARM TRANSMISSION TEST
Removing and placing of magnet unit enables
the alarm transmission test feature.
Check that the transceiver unit indicates at least
2 events – one for removing and one for placing
the magnet.
To check this function it is necessary to verify
that the FREEWAVE2 control panel displays the
following massage:
The message appears when removing the
magnet unit and disappears while placing the
magnet back (X = zone number from which the
massage received).
16 17 18
TAMPER TRANSMISSION TEST
Pressing and releasing the tamper (push button)
enables the TAMPER transmission test feature.
Verify the Control Panel indicates "Zone Tamper
open" and TROUBLE LED is ON.
Close the Tamper and verify the Control Panel
Indicates ZONE TAMPER OPEN is restored and
TROUBLE LED is OFF.
In some control panels READY LED will turn OFF
when tamper is open and ON when closed.
Transmission can also be reviewed on the
transceiver unit as a rapid Red-Green-LED blink.
EXTERNAL MAG
It is optional to use additional magnet units
connected to the MAG terminal input. This
connection is protected by End Of Line resistor value
8.2Khom. Alarm transmission, triggered by intrusion
detection at WIRE terminal input, provides signals of
door/window open/close up to 15m. Connect two
wires communication cable to the MAG terminal
block inputs. See Fig.3.
BATTERY REPLACEMENT
 Remove the front cover.
 Pull out the old battery.
 Install a new battery according to polarity marking.
 After assembling the battery the LED will flash
Green then Red alternately for 45 seconds.
During this time the detector does not function,
wait until the LED stop flashing.
 Press tamper for 2 sec and then release it.
 Note LED indications:
Green/Red LED flashes 6 times alternately:
The detector was successfully registered in system.
The cover may be placed back and closed.
Green LED blinks 20 times:
No response from Transceiver / device was not
assigned on CP - Repeat installation procedure.
Red LED blinks continually (over 20 sec):
Battery voltage is critical low device won't
function - Replace battery.
REGULATORY APPROVALS
The FW2-MAG conforms to the essential requirements set
out by:
 RTTE directive:1999/5/EC
 EMC directive: 2004/108/EC
 Low Voltage directive: 2006/95/EC
Harmonized Standards applicable to this products are:
 EN300220-2
 EN301489-3
 EN301489-1
 EN50130-4
 EN61000-6-3
 EN60950-1
 EN50131-6
 EN50130-5
 EN50131-5-3
Security Grade 2 Environmental Class II
Additional Standards and Directives applicable to this
product are:
 RoHS directive: 2002/95/EC
 EN50131-2-6: 2004
19 20
FCC & IC STATEMENT
FCC ID: NFC-FW2MAG9F
IC: 8164A-FW2MAG9F
This device complies with FCC Rules Part 15 and with Industry
Canada license-exempt RSS standard(s). Operation is subject
to two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference
that may be received or that may cause undesired operation.
Canada: Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
FCC & IC STATEMENT (Continue)
NOTE: The digital circuit of this device has been tested and
found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician
for help.
WARNING:
Changes or modifications to this equipment not expressly
approved by the party responsible for compliance (Crow
Electronic Engineering Ltd.) could void the user’s authority to
operate the equipment.
TECHNICAL SPECIFICATIONS
Data Protocol FreeWave2
Modulation Type GFSK (1 Frequency)
Frequency 868.35MHz / 868.85MHz / 916.5 MHz
Identification Unique ID serial number – 24 bit
Event Transmission Alarm, Tamper, Supervision, Low Bat
Supervision
Detection Method Internal Reed Switch or External
Magnet Device
Range in open space 500m
Battery Lithium. 3V Type: CR123A Size:
2/3AA
Battery life expectancy >5 years ( 10 activation per day)
Current Consumptions:
Standby ~3 A
Receive mode ~29 mA
Transmit mode ~38 mA
Low Battery ~2.4Vdc
Transmit power: ~10dBm
Tamper Switch Front Cover Removal;
Back Tamper
External Input Up to 15m with 8.2Kohm EOL resistor
Operating temperature -10C to +50C
Dimensions 97mm x 22mm x 21mm
Weight (inc. battery) 40 gr.
22 23
CROW ELECTRONIC ENGINEERING LTD. ("Crow") - WARRANTY POLICY CERTIFICATE
This Warranty Certificate is given in favor of the purchaser (hereunder the "Purchaser") purchasing the products directly from Crow or from its
authorized distributor.
Crow warrants these products to be free from defects in materials and workmanship under normal use and service for a period of 24 months from the
last day of the week and year whose numbers are printed on the printed circuit board inside these products (hereunder the "Warranty Period").
Subject to the provisions of this Warranty Certificate, during the Warranty Period, Crow undertakes, at its sole discretion and subject to Crow's
procedures, as such procedures are form time to time, to repair or replace, free of charge for materials and/or labor, products proved to be defective in
materials or workmanship under normal use and service. Repaired products shall be warranted for the remainder of the original Warranty Period.
All transportation costs and in-transit risk of loss or damage related, directly or indirectly, to products returned to Crow for repair or replacement shall
be borne solely by the Purchaser.
Crow's warranty under this Warranty Certificate does not cover products that is defective (or shall become defective) due to: (a) alteration of the
products (or any part thereof) by anyone other than Crow; (b) accident, abuse, negligence, or improper maintenance; (c) failure caused by a product
which Crow did not provide; (d) failure caused by software or hardware which Crow did not provide; (e) use or storage other than in accordance with
Crow’s specified operating and storage instructions.
There are no warranties, expressed or implied, of merchantability or fitness of the products for a particular purpose or otherwise, which extend beyond
the description on the face hereof.
This limited Warranty Certificate is the Purchaser's sole and exclusive remedy against Crow and Crow's sole and exclusive liability toward the
Purchaser in connection with the products, including without limitation - for defects or malfunctions of the products. This Warranty Certificate replaces
all other warranties and liabilities, whether oral, written, (non-mandatory) statutory, contractual, in tort or otherwise.
In no case shall Crow be liable to anyone for any consequential or incidental damages (inclusive of loss of profit, and whether occasioned by
negligence of the Crow or any third party on its behalf) for breach of this or any other warranty, expressed or implied, or upon any other basis of liability
whatsoever. Crow does not represent that these products can not be compromised or circumvented; that these products will prevent any person injury
or property loss or damage by burglary, robbery, fire or otherwise; or that these products will in all cases provide adequate warning or protection.
Purchaser understands that a properly installed and maintained product may in some cases reduce the risk of burglary, fire, robbery or other events
occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property
loss or damage as a result.
Consequently, Crow shall have no liability for any personal injury; property damage or any other loss based on claim that these products failed to give
any warning.
If Crow is held liable, whether directly or indirectly, for any loss or damage with regards to these products, regardless of cause or origin, Crow’s
maximum liability shall not in any case exceed the purchase price of these products, which shall be the complete and exclusive remedy against Crow.
CROW ELECTRONIC ENGINEERING LTD.
12 Kineret St.
Airport City, 70100 Israel
Tel. [phone]
Fax. [phone]
[e-mail]
[e-mail]
www.thecrowgroup.com
CROW LATIN AMERICA USA INC.
7200 NW 19 st.
Suite 307
Miami FI 33126, USA
Tel. [phone]
Fax. [phone]
[e-mail]
www.crowlatinamerica.com
ARROWHEAD ALARM PRODUCTS
344B, Rosedale Road
Park Farm Industrial Estate
Albany, Auckland
New Zealand
Tel. [phone]
Fax. [phone]
88
www.aap.co.nz
These instructions supersede all previous
issues in circulation prior to March 2012.
7101590 Rev. C
Zone # X Open
Door / Window
FW2-MAG
Magnet unit
N345