Charcoal Grill User Manual

ManualsBrandsCrown Verity ManualsGrillBI-48

CROWN VERITY INC., 37 ADAMS BLVD., BRANTFORD, ON. CAN. N3S 7V8

TEL: (519) 751-1800 FAX: (519) 751-1802

www.crownverity.com

Email: info@crownverity.com

OWNER’S MANUAL

“SUPPLEMENT FOR BUILT-IN UNITS”

MODELS: BI-30, BI-36 & BI-48

REVISED MARCH, 2003

*PLEASE RETAIN FOR FUTURE REFERENCE

THANK YOU for purchasing this quality product. Your Crown Verity Inc. charbroiler

will give you years of outdoor cooking enjoyment.

Please read this manual carefully to ensure safe operation and to maximize your

cooking enjoyment. It is your responsibility to see that your unit is properly

assembled, installed and cared for. Failure to follow instructions in this manual could

result in serious bodily injury and/or property damage.

WARNING: Improper installation, adjustment, alteration, service or

maintenance can cause property damage, injury or death. Read the

installation, operating and maintenance instructions thoroughly before

installing or servicing this equipment.

Summary of content (12 pages)

PAGE 1
OWNER’S MANUAL “SUPPLEMENT FOR BUILT-IN UNITS” MODELS: BI-30, BI-36 & BI-48 REVISED MARCH, 2003 *PLEASE RETAIN FOR FUTURE REFERENCE THANK YOU for purchasing this quality product. Your Crown Verity Inc. charbroiler will give you years of outdoor cooking enjoyment. Please read this manual carefully to ensure safe operation and to maximize your cooking enjoyment. It is your responsibility to see that your unit is properly assembled, installed and cared for.
PAGE 2
1 This owner’s manual was created as a supplement to the standard MCB manual to assist you and the contractor(s) you have hired to install the BI-30, BI-36 or BI-48. The standard MCB manual contains a lot of valuable safety and operation information. Please read through the manual before operating your charbroiler, paying special attention to the safety, operation, and shut down instructions. Not all of the information will apply to you. It will be up to you to decide what applies and what doesn’t.
PAGE 3
2 PLANNING YOUR PROJECT A built-in Crown Verity Inc. charbroiler requires some sort of support structure to house the unit. In all cases, this is a custom made project involving a gas technician and possibly other contractors, i.e. mason, carpenter, electrician, plumber, etc. It is important that you form a clear and concise plan before beginning. We strongly suggest purchasing your broiler and accessories before beginning.
PAGE 4
3 The following diagrams represent mechanical clearances (areas that must be kept free of obstructions). Of particular concern is the roll dome. Whether or not you purchased one with your unit, there are some clearances to maintain should you wish to add or remove a roll dome (Diagram #1). Also, the roll dome requires some clearance in order to operate (Diagram #2).
PAGE 5
4 Diagram #2 Roll Dome Operating Clearance 7” • Roll dome requires min. 7” operating clearance from rear edge Diagram #3 Rotisserie Clearance 12” 6” CROWN VERITY INC., 37 ADAMS BLVD., BRANTFORD, ON. CAN. N3S 7V8 TEL: (519) 751-1800 FAX: (519) 751-1802 www.crownverity.com Email: info@crownverity.
PAGE 6
5 CLEARANCE TO COMBUSTIBLE MATERIALS: Of particular concern are clearances to combustible materials (i.e. wood, plastics, fibres, plant life, flammables, etc). Diagram #4 Clearance to adjacent combustible & heat affected materials 18” 18” 18” Top View BI-48 shown with front shelf Be careful when placing a broiler against a wall. The smoke that exits the vents at the rear of a roll dome can quickly blacken brickwork and other surfaces! Diagram #5 Overhangs / Ceilings Crown Verity Inc.
PAGE 7
6 Diagram #6 23” min. 23-1/4” max. ” “A Cut-out dimensions Models BI-30, BI-36, BI-48 16” min. 16-1/4” max. BI-30 BI-36 BI-48 TABLE Dimension “A” 30-3/4” min. - 31” max. 37” min. - 37-1/4” max. 48-3/4” min. - 49” max. We hope that the information contained in this manual has helped you make some informed decisions with respect to the location and dimensions of your structure. It is imperative that all parties involved are aware of the limitations and requirements before construction begins.
PAGE 8
7 NOTE TO GAS TECHNICIAN: The installation of this appliance must be in accordance with: 1) All applicable local codes, or in the absence of local codes: 2) i) Canada: must conform to current National Standard CAN/CGA B149.1/.2 natural gas/propane installation code. ii) U.S.A.: must conform to national Fuel Gas Code, ANSI Z2223.2, 1988 or latest edition. DO NOT perform any pressure tests on this appliance or the regulator supplied in excess of 1/2 PSIG.
PAGE 9
8 NOTE TO PLUMBERS AND ELECTRICIANS: DO NOT install any electrical or plumbing materials affected by elevated temperatures within 18” of any side of this appliance. Rotisserie outlet power requirements: 115 v 45 AMP straight blade receptacle. Centre line of outlet face must be within 30 inches of rotisserie motor mounting slot on left side of the appliance for the cord set to reach. NOTE TO MASONS/CARPENTERS/ETC: Make sure your client has selected suitable materials for the application.
PAGE 10
NOTES _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ ____________________________________________________________________________
PAGE 11
NOTES _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ ____________________________________________________________________________
PAGE 12
CROWN VERITY INC., 37 ADAMS BLVD., BRANTFORD, ON. CAN. N3S 7V8 TEL: (519) 751-1800 FAX: (519) 751-1802 www.crownverity.com Email: info@crownverity.