Crown Power Amplifiers ®
INSTALLED SOUND CTs 2-Channel Series CTs Multi-Channel Series CTs Multi-Channel with CobraNetTM CDi Series DSi Series
AMPLIFIERS INSTALLED SOUND CTs Series: The New Standard CTs 600, CTs 1200, CTs 2000, CTs 3000 Foundation `` FEATURES • • • • • High power density. All two channel models in a 2U chassis. New Crown Switching Power Supply for lighter weight. Selectable “Constant-Voltage” or low-impedance operation per channel. 100V direct outputs on all models. Fully PIP2-compatible.
`` SPECIFICATIONS Frequency Response (at 1 watt, 20 Hz - 20 kHz): ±0.25 dB. Signal to Noise Ratio below rated power (20 Hz to 20 kHz): 105 dB A-weighted. Total Harmonic Distortion (THD) at full rated power, from 20 Hz to 20 kHz: CTs 600/1200: < 0.1%. CTs 2000/3000 < 0.35%. Damping Factor: 10 Hz to 100 Hz: > 3000. Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB. Common Mode Rejection (CMR) (20 Hz to 1 kHz): 50 dB. DC Output Offset: < ±2 mV.
AMPLIFIERS INSTALLED SOUND CTs Multi-Channel Series: The New Standard CTs 4200, CTs 8200 Flexibility `` FEATURES • • • • • • High power density: Four-channel model in a 2U chassis, eight-channel model in a 3U chassis. New Crown Switching Power Supply for lighter weight. Selectable “Constant-Voltage” or low-impedance (4/8 ohm) operation per channel-pair. 100V direct outputs. New “FIT” (Fault Isolation Topology) circuitry isolates fault conditions without affecting neighboring channels.
`` SPECIFICATIONS Frequency Response (at 1 watt, 20 Hz - 20 kHz): ±0.5 dB. Phase Response (at 1 watt, 10 Hz - 20 kHz): ±35°. Signal to Noise Ratio below rated power (20 Hz to 20 kHz): 100 dB unweighted. Total Harmonic Distortion (THD) at 1 watt, from 20 Hz to 20 kHz: < 0.05%. Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from 163 milliwatts to full bandwidth power: < 0.05% (typical). Damping Factor: 10 Hz to 400 Hz: >180. Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB.
AMPLIFIERS INSTALLED SOUND CTs Multi-Channel Series: With CobraNet CTs 4200USP/CN, CTs 8200USP/CN CobraNet Capable TM `` FEATURES (input module) • • • • • • 100 Mbps Ethernet single-plug solution for CobraNet audio, and HiQnet™ control and monitoring. Analog audio inputs allow CobraNet network audio input, CobraNet audio backup, or a hardwire emergency override of CobraNet audio. 24 bit digital to analog conversion with 32 bit, floating point DSP processing. Firmware upgrades via the network.
`` SPECIFICATIONS USP/CN CobraNet Module Specifications (for amplifier specifications, see the CTs MultiChannel Series pages) Connectors: AUX Connector Configurable for AUX input, AUX output and Listen Bus. Listen Bus is also supported through CobraNet. Network Connector The dual RJ45 CobraNet connectors allow a Primary & Secondary connection to the 100Mb Ethernet network.
AMPLIFIERS INSTALLED SOUND CDi Series: 2/4/8 Ohm, 70V/100V per channel CDi 1000, CDi 2000, CDi 4000, CDi 6000 Versatility `` FEATURES • • • • • • Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting. Computer connectivity via USB allows fast setup and configuration with HiQnet™. Barrier strip outputs, removable Phoenix-style input. Extremely versatile, handling a wide range of speaker impedances and outputs. Switch-mode universal power supply.
`` SPECIFICATIONS Performance Output Power: See power charts below. Voltage Gain at 1kHz: CDi 1000: 30.5 dB CDi 2000: 32.9 dB CDi 4000: 34.2 dB CDi 6000: 37.1 dB Frequency Response: +0/–1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. Sensitivity: 1.4V. Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 100 dB (A weighted).
AMPLIFIERS INSTALLED SOUND DSi Series: 2, 4, 8 ohm DSi 1000, DSi 2000, DSi 4000, DSi 6000 One-touch Performance `` FEATURES • • • • • Intuitive front-panel LCD screen, automatic presets for popular JBL speaker systems for quick, easy configuration. Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting. Computer connectivity via USB allows fast setup and configuration with HiQnet™. Barrier strip outputs, removable Phoenix-style input. All models are THX®-approved.
`` SPECIFICATIONS Performance Voltage Gain at 1kHz: DSi 1000: 30.5 dB DSi 2000: 32.9 dB DSi 4000: 34.2 dB DSi 6000: 37.1 dB Frequency Response: +0/–1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. DSi 1000 A1 (100V version) is rated for 4 to 8 ohms in Stereo mode, 8 to 16 ohms in Bridge-Mono mode. Sensitivity: At 8 ohm rated output: DSi 1000: 1.4V DSi 2000: 1.4V DSi 4000: 1.
COMMERCIAL AUDIO Preamplifier-Mixers Amplifiers Mixer-Amplifiers XM Business Music Systems
COMMERCIAL AUDIO PREAMPLIFIER-MIXERS 14M, 28M Adaptable `` FEATURES • • • • • • • 4 or 8 inputs, 1 or 2 output channels. Ideal for commercial and industrial use. Balanced Phoenix-type mic/line inputs; RCA inputs. Balanced Phoenix-type line outputs. Any input can be sent to any output. Priority muting. Independent bass and treble controls for each input.
`` SPECIFICATIONS Performance Frequency Response (at line out): 20 Hz to 20 kHz +/- 1 dB. Signal to Noise Ratio (master volume at minimum): 100 dB. THD: 0.05% typical with 800 mV balanced input, 1V output. Input Sensitivity (volts RMS for full output at maximum gain): Balanced mic inputs: 3 mV. Balanced line inputs: 800 mV. RCA connectors: 400 mV. Input Impedance (nominal): Mic: 400 ohms. Line: 100 kilohms. RCA: 50 kilohms. Crosstalk (all controls at “10”): –50 dB at 1kHz.
COMMERCIAL AUDIO AMPLIFIERS 180A, 280A, 1160A Power Zone `` FEATURES • • • • Ideal for commercial and industrial use. Balanced Phoenix-type line inputs; touch-proofed screw-terminal speaker outputs. Advanced protection system includes output current limiting, DC protection, circuit breaker/fuse, and thermal protection. 1 or 2 inputs; 1 to 2 amplifier output channels.
`` SPECIFICATIONS Performance Frequency Reponse (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz +/- 1 dB. Frequency Response (at line out): 20 Hz to 20 kHz +/- 1 dB. Power Bandwidth (at 4-ohm tap, 2 dB below maxium 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB. DC Output Offset: < ±5 mV. THD: Less than 0.5% at rated power at 1 kHz. Input Sensitivity (for full output at maximum gain): 800 mV. Input Impedance (nominal): 100 kilohms.
COMMERCIAL AUDIO AMPLIFIERS 660A 6-Channel `` FEATURES • • • • 6 inputs; 6 amplifier output channels. Balanced Phoenix-type line inputs; touch-proof screw-terminal speaker outputs. Advanced protection system includes output current limiting, DC protection, circuit breaker/fuse, and thermal protection. Ideal for commercial and industrial use. POWER OUTPUT* Model 4-ohm 660A 60W 70V/100V Inputs 60W 6 *Minimum guaranteed power in watts at 1 kHz with 0.5% THD.
`` SPECIFICATIONS Frequency Reponse (at 1 watt from 4-ohm tap): 100 Hz to 19 kHz +/- 1 dB. Frequency Response (at line out): 20 Hz to 20 kHz +/- 1 dB. Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB. DC Output Offset: < ±5 mV. THD: Less than 0.5% at rated power at 1 kHz. Input Sensitivity (for full output at maximum gain): 800 mV. Input Impedance (nominal): 100 kilohms. Minimum Load Impedance: 100V output: 160 ohms. 70V output: 80 ohms. 4-ohm output: 4/8 ohms.
COMMERCIAL AUDIO MIXER-AMPLIFIERS 180MA, 280MA, 1160MA Practical `` FEATURES • • • • • 4 to 8 inputs, 1 to 2 amplifier output channels. Ideal for commercial and industrial use. Balanced Phoenix-type mic/line inputs; touch-proofed screw-terminal speaker outputs. Any input can be sent to any output. Priority muting.
`` SPECIFICATIONS Performance Frequency Reponse (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz ± 1 dB. Frequency Response (at line out): 20 Hz to 20 kHz ± 1 dB. Power Bandwidth (at 4-ohm tap, 2 dB below maxium 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB. DC Output Offset: < ±5 mV.
COMMERCIAL AUDIO MIXER-AMPLIFIERS 135MA, 160MA Practical `` FEATURES • • • • • 3 inputs and one 35W amplifier output channel in 135MA. 4 inputs and one 60W amplifier output channel in 160MA. Ideal for paging, background music, and music-on-hold. Voice-activated priority muting (VOX). Pre-amp outputs. POWER OUTPUT* Models 8-ohm 70V/100V 135MA 160MA 35W 60W 35W 60W Inputs System Zones 3 4 Single-zone Single-zone *Minimum guaranteed power in watts at 1 kHz with 0.5% THD.
`` SPECIFICATIONS Performance Frequency Response (at 1 watt from line out): 50 Hz to 20 kHz ± 1 dB. 19 Hz to 34 kHz +0, –3 dB. Input Signal Clip Indicators: Green LED, one above each channel's input attenuator, flashes brightly at threshold of audible distortion. Signal to Noise Ratio (ref. to rated power, master volume at minimum): Output Signal Presence Indicator: Green LED above master output volume control illuminates when any input signal exceeds –40 dBu. Mic: > 58 dB. Line: > 60 dB.
COMMERCIAL AUDIO MIXER-AMPLIFIERS 140MPA Music & Paging `` FEATURES • • • • • 4 inputs (each with a volume control), one 40W amplifier output channel. Ideal for paging, background music, and music-on-hold. Balanced Phoenix-type mic/line inputs, telephone input, dual RCA stereo music inputs, touch-proof screw-terminal speaker outputs. Priority ducking. Independent bass and treble controls for each input.
`` SPECIFICATIONS Performance Frequency Reponse (at 1 watt from 4-ohm tap): 50 Hz to 15 kHz ± 1 dB. Frequency Response (at line out): 50 Hz to 15 kHz ± 1 dB. Power Bandwidth (at 4-ohm tap, 2 dB below maxium 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD. Signal to Noise Ratio (ref. to rated power, master volume at minimum): >90 dB. DC Output Offset: < ±5 mV. THD: < 0.5% at rated power at 1 kHz. Input Sensitivity (for full output at maximum gain): Balanced mic inputs: 3 mV. Balanced line inputs: 800 mV.
COMMERCIAL AUDIO XM TUNER-MIXER-AMPLIFIERS 180MAx Pack (180MAx tuner-mixer-amplifier also available separately) XM Enabled `` FEATURES • • • Programmable XM tuner with XM channel data display. Independent bass and treble controls for each input. Balanced Phoenix-type mic/line inputs; touch-proof screwterminal speaker outputs. Priority ducking, Music-On-Hold (MOH) outputs. 180 MAx Pack includes four JBL Control 1ST 2-way speakers with 70V transformer and mounting brackets, remote control and XM antenna.
`` SPECIFICATIONS Performance Frequency Reponse (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz ±1 dB. Frequency Response (at line out): 20 Hz to 20 kHz ±1 dB. Power Bandwidth (at 4-ohm tap, 2 dB below maxium 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB. DC Output Offset: < ±5 mV. THD: Less than 0.5% at rated power at 1 kHz. Input Sensitivity (for full output at maximum gain): Balanced mic inputs: 3 mV. Balanced line inputs: 800 mV.
PORTABLE PA XTi Series XLS Series
AMPLIFIERS PORTABLE PA XTi Series: World Class XTi 1000, XTi 2000, XTi 4000, XTi 6000 World-Class `` FEATURES • • • • • • • • Computer connectivity via USB allows fast setup and configuration with HiQnet™. Integrated speaker presets with LCD front panel display. Extremely versatile, handling a wide range of speaker impedances and outputs. Switch-mode universal power supply. Speaker presets for Crossover Frequencies, EQ, Limiting, and Delay.
`` SPECIFICATIONS Voltage Gain at 1kHz, 8 ohm rated output: XTi 1000: 30.5 dB XTi 2000: 32.9 dB XTi 4000: 34.2 dB XTi 6000: 37.1 dB Frequency Response: +0/–1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. The XTi 1000 A1 (100V version) is rated for 4 to 8 ohms Stereo, 8 to 16 ohms Bridge Mono. Sensitivity: 1.
AMPLIFIERS PORTABLE PA XLS-III Series: Performance and Flexibility XLS1000, XLS1500, XLS2000, XLS2500 Innovation `` FEATURES • High Performance, Lightweight Class-D amplifier – weighs less than 11 lbs. • Integrated PureBand™ Crossover system ensures seamless transitions from low to high frequency drivers. • Integrated PeakX™ Limiters provide maximum output while protecting your speakers. • XLR, 1/4", RCA Inputs ensure compatibility with any source.
`` SPECIFICATIONS Performance Sensitivity (for full rated power at 4 ohms): 1.4 Vrms. Frequency Response (at 1 watt, 20 Hz to 20 kHz): +0 dB, –1 dB. PureBandTM Crossover System Crossover Filter: Linkwitz-Riley 24dB per ocatve. Crossover Mode: Crossover (CH1=LPF, CH2=HPF), Low Pass (both channels LPF), High Pass (both channels HPF), Bridge (LPF or HPF). Signal-to-Noise Ratio Rated as dBr to full rated 8 ohms power output (A-weighted): XLS1000: > 97 dB. XLS1500, XLS2000, XLS2500: > 103 dB.
AMPLIFIERS PORTABLE PA XLS Series: Affordable and Reliable XLS 5000 Evolution `` FEATURES • • • • Housed in a rugged, all-steel 3U chassis. Efficient forced-air fan prevents excessive thermal buildup. Electronically balanced XLR inputs; touchproof binding post and Speakon outputs. Precision detented level controls, power switch, and four LEDs, which indicate clip for each channel, power and fault conditions.
`` SPECIFICATIONS Performance Sensitivity (for full rated power at 4 ohms): 1.25 Vrms. Frequency Response (at 1 watt, 22 Hz to 20 kHz): +0 dB, –1 dB. Signal-to-Noise Ratio (20 Hz to 20 kHz, inputs terminated): A-weighted, below rated power: > 100 dB. No weighting, below rated power: > 95 dB. Total Harmonic Distortion (THD): < 0.5%. Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) from full rated output to –40 dB: < 0.3%. Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.
TOURING I-Tech HD Series Macro-Tech i Series
AMPLIFIERS TOURING I-Tech Series: Excellence Without Compromise I-T4000, I-T6000, I-T8000 Raising the Bar–Again `` FEATURES • • • • • • • BSS OMNIDRIVEHD™ DSP processing with IIR and linear phase FIR filters. Global Power Supply designed to deliver maximum power no matter where your schedule takes you. Universal AC input accepts100-240VAC, 50/60 Hz (±15%). High power density, up to 9000 watts in a 2U chassis. Highest output voltage in the industry (200V peak) provides clean transient peaks.
`` SPECIFICATIONS Summary Specifications Input Sensitivity (referenced to 8 ohm rated output): Adjustable in 0.1V steps from 1.4V to 7.75V. Signal to Noise Ratio below rated full-bandwidth power, A-weighted: > 112 dB. Required AC Mains: Universal AC input, 100240VAC, 50/60 Hz (±15%). Maximum AC mains voltage 277VAC. Frequency Response (at 1 watt, 20 Hz - 20 kHz): ±0.25dB. Total Harmonic Distortion (THD) at full rated power: < 0.1%.
AMPLIFIERS TOURING Macro-Tech i Series: The Legend Continues Macro-Tech i Series The Legend Continues `` FEATURES • The Macro-Tech® i Series continues the Crown® Macro-Tech legacy of unparalleled sonic accuracy and detail, putting sound quality above all else • Patented, cutting-edge Class-I circuitry gets more power out of an amplifier with less waste • Rugged construction ensures that all Macro-Techs are built to withstand years of abuse on the road • Global Power Supply — designed to deliver maximum
`` SPECIFICATIONS Performance Frequency Response (at 1 watt, 20 Hz - 20 kHz into 8 ohms): ±0.25 dB. Signal to Noise Ratio (below rated full-bandwidth power, A-weighted): >112 dB. Total Harmonic Distortion (THD) (at 2 watts into 8 ohms): < 0.1%. Total Harmonic Distortion (THD) Plus Noise (at full rated power): < 0.35%, 20 Hz to 20 kHz. Intermodulation Distortion (IMD) (60 Hz and 7 kHz at 4:1, from full rated output to –30 dB): < 0.35%. Damping Factor (20 Hz to 100 Hz at 8 ohms): > 5000.
RECORDING & BROADCAST D Series
AMPLIFIERS RECORDING & BROADCAST D Series: Long-Term Favorites D-45, D-75A Tried & True `` FEATURES • • • • • • Powerful AB+B class circuitry yields maximum efficiency with minimum crossover “notch” distortion. IOC® (Input/Output Comparator) alerts of any distortion that exceeds 0.05% to provide proof of distortion-free performance. Ultra-low harmonic and intermodulation distortion result in the best dynamic transfer function in the industry.
`` SPECIFICATIONS Performance Frequency Response: ±0.1 dB from 20 Hz to 20 kHz at 1watt. Phase Response: +10 to –15 degrees from 20 Hz to 20 kHz at 1 watt. Signal-to-Noise: 106 dB from 20 Hz to 20 kHz at full bandwidth FTC power. Total Harmonic Distortion (THD): Less than 0.001% at full bandwidth FTC power from 20 Hz to 400 Hz increasing linearly to 0.05% at 20 kHz. Intermodulation Distortion (IMD): (60 Hz and 7 kHz 4:1) Less than 0.01% from 0.25 watts to full bandwidth FTC power, and less than 0.
CINEMA DSi Series CTs 2-Channel Series CTs Multi-Channel Series
AMPLIFIERS CINEMA DSi Series: 2/4/8 Ohm DSi 1000, DSi 2000, DSi 4000, DSi 6000 One-Touch Performance `` FEATURES • • • • • • Intuitive front-panel LCD screen, automatic presets for popular JBL cinema speaker systems for quick, easy configuration. Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting. Computer connectivity via USB allows fast setup and configuration with HiQnet™ System Architect® software.
`` SPECIFICATIONS Performance Voltage Gain at 1kHz: DSi 1000: 30.5 dB DSi 2000: 32.9 dB DSi 4000: 34.2 dB DSi 6000: 37.1 dB Frequency Response: +0/–1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. DSi 1000 A1 (100V version) is rated for 4 to 8 ohms in Stereo mode, 8 to 16 ohms in Bridge-Mono mode. Sensitivity: At 8 ohm rated output: DSi 1000: 1.4V DSi 2000: 1.4V DSi 4000: 1.4V DSi 6000: 1.
AMPLIFIERS CINEMA DSi-8M: Convenient Monitoring DSi-8M Performance Monitor `` FEATURES • • • • • • Compact 2-rack unit. 8 channels for monitoring processor or amplifier inputs. All inputs and outputs are balanced to interface with new cinema processors. No level jumps when switching between processor and amplifiers. 25-pin D-sub connectors, plus removable terminal blocks and HD-15 for quick, hassle-free connections.
`` SPECIFICATIONS Performance Input Impedance (processor inputs): 10 kilohms. Input Impedance (Processor Inputs): 10 k ohms. Input Impedance (Power Amplifiers Inputs): > 50 k ohms. Power Requirements: 100-240V , 50-60 Hz, 32 watts. Front Panel Controls and Indicators Channel Select Buttons and LEDs: Eight pushbutton switches, one for each input channel. Pressing a button monitors the signal from that channel, and lights the corresponding LED. Any combination of eight channels can be selected.
AMPLIFIERS CINEMA Other Cinema Products CTs 2-Channel `` FEATURES • • • • • High power density. All two channel models in a 2U chassis. New Crown Switching Power Supply for lighter weight. Selectable “Constant-Voltage” or low-impedance operation per channel. 100V direct outputs on all models. Fully PIP2™-compatible.
AMPLIFIERS CINEMA Other Cinema Products CTs Multi-Channel `` FEATURES • • • • • • High power density: Four-channel model in a 2U chassis, eight-channel model in a 3U chassis. New Crown Switching Power Supply for lighter weight. Selectable “Constant-Voltage” or low-impedance (4/8 ohm) operation per channel-pair. 100V direct outputs. New “FIT” (Fault Isolation Topology) circuitry isolates fault conditions without affecting neighboring channels. Accept VCA-MC accessory modules.
NETWORKED PRODUCTS & ACCESSORIES PIPs Accessories
NETWORKED PRODUCTS PIPS TCP / IQ ANALOG AUDIO INPUTS PIP LITE PIP USP3/CN T T SmartAmp Automation for Networked Audio he Crown PIP LITE is a PIP (Programmable Input Processor) input module for PIP2 compatible amplifiers. The PIP-LITE connects to an audio control network via 100 Mb Ethernet. The audio path in the PIP LITE is processed totally in the analog domain.
FEATURES PIP USP4 T he Crown® PIP-USP4 is a 4th generation DSP-based PIPTM (Programmable Input Processor) input module for CTs Series two channel amplifiers. The USP4 connects to an Ethernet network allowing it to be remotely controlled and monitored via System Architect. In addition, the USP4 allows the transport of real-time digital audio via AES3, CobraNetTM or Ethernet AVB.
ACCESSORIES & APPLICATIONS ACCESSORIES Accessories VCA-MC4A & VCA-MC8 `` FEATURES • 1-VCAP & 4-VCAP • `` FEATURES • • • • 1-VCAP provides remote volume control for one or more CTs amplifier channels. Fits into a 1-gang electrical box. 4-VCAP provides remote volume control for four or more CTs amplifier channels. Fits into a 2-gang electrical box.
ACCESSORIES & APPLICATIONS ACCESSORIES Accessories cya (cover your amp) P.I.P.-CLP The P.I.P.-C.L.P. is designed to detect and prevent overload. The same error detecting circuit that is used to signal the IOC indicator is used to activate this error-driven compressor. It is not a typical signal-driven compressor but a circuit to prevent an overload. It can yield up to 13 dB of additional signal safety margin without noticeable program change.
PRODUCT APPLICATIONS & WARRANTY Installed Sound Product Applications Live Sound Product Applications Crown Amplifier Warranty
ACCESSORIES & APPLICATIONS INSTALLED SOUND PRODUCT APPLICATIONS
ACCESSORIES & APPLICATIONS INSTALLED SOUND PRODUCT APPLICATIONS
ACCESSORIES & APPLICATIONS LIVE SOUND PRODUCT APPLICATIONS
Crown Amplifier Warranty USA AND CANADA SUMMARY OF WARRANTY Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A. warrants to you, the ORIGINAL PURCHASER and ANY SUBSEQUENT OWNER of each NEW Crown product, for a period of three (3) years from the date of purchase by the original purchaser (the “warranty period”) that the new Crown product is free of defects in materials and workmanship.
Crown Amplifier Warranty WORLDWIDE EXCEPT USA & CANADA SUMMARY OF WARRANTY Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A.
