User`s manual

Crown Broadcast FME 350W to 2000W User Manual– 05/2013
Page 74
Crown Broadcast, a division of International Radio & Electronics Corporation 25166 Leer Drive, Elkhart, Indiana, 46514-5425 USA
Ph [phone]
NAME
Access
(R/W)
Possible value on the
serial port of the unit
Comments
INPUT.MPX1.PRESENCE R
MO" or "MO+R" or
"MO+R+S" or "ST" or
"ST+R" or "ST+R+S"
Gives the composition of MPX1 on channel 3. R =
RDS ; MO = Mono ; ST = Stereo ; S = SCA
INPUT.MPX1.SW.PRIO R/W 0..7 ; 0=disabled Priority of each audio channel (4= highest priority)
INPUT.MPX1.TYPE R/W
"MO" or "ST" or "ST+R+S" or
"ST+R" or "RDS" or
"RDS+SCA" or "SCA"
Sets the type of signal on the MPX1 input and
applies the corresponding filter
INPUT.MPX2.DRIVE R/W -6.00...6.00
Drive setting, allows an increase of the input audio
level without changing the deviation setting.
INPUT.MPX2.LEVEL R/W -18.00...+18.00 Internal numerical gain
INPUT.MPX2.PEAK R -150…150
Gives the deviation max peak value of the
transmitted signal in kHz over 100 milliseconds
INPUT.MPX2.PKMAX R -150...150
Gives the deviation max peak value of the
transmitted signal in kHz over 1 second
INPUT.MPX2.PRESENCE R
MO" or "MO+R" or
"MO+R+S" or "ST" or
"ST+R" or "ST+R+S"
Gives the composition of MPX2 on channel 3. R =
RDS ; MO = Mono ; ST = Stereo ; S = SCA
INPUT.MPX2.SW.PRIO R/W 0..7 ; 0=disabled Priority of each audio channel (4= highest priority)
INPUT.MPX2.TYPE R/W
"MO" or "ST" or "ST+R+S" or
"ST+R" or "RDS" or
"RDS+SCA" or "SCA"
Sets the type of signal on the MPX1 input and
applies the corresponding filter
INPUT.PLAYER.DRIVE R/W -6.00 to 6.00
Drive setting, allows an increase of the input audio
level without changing the deviation setting.
INPUT.PLAYER.FLT R/W 0;1;2 0=15;1=16;2=17 Configuration of the audio filter
INPUT.PLAYER.LEFT.PEAK R -100 … 28
Gives the left audio input max peak value over 100
milliseconds
INPUT.PLAYER.LEFT.PKMAX R -100 … 28
Gives the left audio input max peak value over 1
second.
INPUT.PLAYER.LEVEL R/W -20...0 Internal numerical gain
INPUT.PLAYER.PREAC R/W 0;50;75 Sets the value of the pre-emphasis
INPUT.PLAYER.PRESENCE R OFF or "L" or "R" or "L&R" Indicates audio signals are present on the player
INPUT.PLAYER.RIGHT.PEAK R -100 … 28
Gives the right audio input max peak value over 100
milliseconds
INPUT.PLAYER.RIGHT.PKMA
X
R -100 … 28
Gives the right audio input max peak value over 1
second.
INPUT.PLAYER.SAMPLING R/W "44" or "48" or "96"
Sampling frequency of the internal player audio
signal
INPUT.PLAYER.SW.BACKDEL
AY
R/W XXX=[0…30]
Back delay on the channel with the highest
configurable priority.
INPUT.PLAYER.SW.DELAY R/W XXX=[1…120] Switching delay when loss of audio 1
INPUT.PLAYER.SW.PRIO R/W 0..4 ; 0=disabled Priority of each audio channel (7= highest priority)
INPUT.PLAYER.SW.SILENCE R/W
"L" or "R" or "ANY" or
"BOTH"
Sets on which channel (L,R or L+R) silence
detection must be conducted for the audio input 1
INPUT.PLAYER.SW.THRESH R/W -90…000 Silence triggering level in dBFS on channel 1
INPUT.PLAYER.TRIM R/W -3.00 to 3.00
Sets the offset between left and right channels (+3 =
left channel level is 3 dBu higher than right channel
level)