IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment: Model #: ___________________________ Serial #: ___________________________ Date Purchased: _____________________ Installation & Operation Manual Gas Power Tilt Skillets GLTS-30 & GLTS-40 Model GLTS-40 WARNING Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death.
Gas Power Tilt Skillets SPECIFICATIONS SAFETY PRECAUTIONS Before installing and operating this equipment, be sure everyone involved in its operation is fully trained and aware of precautions. Accidents and problems can be caused by failure to follow fundamental rules and precautions. The following symbols, found throughout this manual, alert you to potentially dangerous conditions to the operator, service personnel, or to the equipment.
Gas Power Tilt Skillets Table of Contents RETAIN THIS MANUAL FOR FUTURE REFERENCE. Table of Contents Important Notes For Installation and Operation .................................................................... 2 Service Connections ............................................................................................................. 4 Installation Instructions ......................................................................................................... 5 Operation ..............
Gas Power Tilt Skillets SERVICE CONNECTIONS SERVICE CONNECTIONS SERVICE CONNECTIONS - Unless otherwise specified, Field Wire Electrical Connection to be 120 Volts, 60 Hz, single phase with grounding wire. Unit furnished with 6’ cord and 3 prong plug. Total max amps 4.0. - GAS CONNECTION: Supply gas through 3/4” pipe. C - COLD WATER: 3/8” O.D. tubing to optional faucet H - HOT WATER: 3/8” O.D.
Gas Power Tilt Skillets INSTALLATION INSTALLATION INSTRUCTIONS UNPACKING IMMEDIATELY INSPECT FOR SHIPPING DAMAGE Immediately after unpacking the steamer, check for possible shipping damage. If the steamer is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
INSTALLATION Gas Power Tilt Skillets Leveling and Anchoring 1. Set the appliance in place and level left to right and front-to-back using spirit level. 2. Mark hole locations on floor through anchoring holes provided in flanged adjustable feet. 3. Remove appliance and drill holes in locations marked on floor and insert proper anchoring devices (not supplied). 4. Set unit back in position and re-level left to right and front to back. 5. Bolt and anchor appliance securely to the floor. 6.
Gas Power Tilt Skillets OPERATION OPERATION NOTICE If this equipment is being installed at over 2,000 feet altitude and was not so specified on order, contact service department. Failure to install with proper orifice sizing may void the warranty. Before First Use Using a non-corrosive, grease-dissolving commercial cleaner, clean the protective metal oils from all surface parts and the interior of the tilting braising pan. Follow the cleaner manufacturer’s directions. Rinse thoroughly and drain the pan.
OPERATION Gas Power Tilt Skillets 6. If gas supply is interrupted during operation, turn THERMOSTAT dial to OFF position and turn gas supply OFF. Wait 5 minutes, then repeat Steps 1 through 4 to restart. 7. Turn power switch and THERMOSTAT to OFF when braising pan is not in use. CAUTION If you smell gas during the lighting procedure, immediately shut off the gas supply until the leak has been corrected.
Gas Power Tilt Skillets Preventative Maintenance Preventative Maintenance WARNING Disconnect the power supply to the appliance before cleaning or servicing. CAUTION Do not use cleaning agents that are corrosive. CAUTION Operating, testing, and servicing should only be performed by qualified personnel. Cleaning After each use, allow the tilting braising pan to cool and clean it. Keep exposed cleanable areas of the tilting braising pan clean at all times.
Gas Power Tilt Skillets Preventative Maintenance CAUTION The appliance and its parts are hot. Use care when operating, cleaning and servicing the appliance. WARNING Disconnect the power supply to the appliance before cleaning or servicing. Adjustments All tilting braising pans are adjusted at the factory. At least twice a year, have an authorized service person clean and adjust the tilting braising pan for maximum performance.
Gas Power Tilt Skillets COOKING GUIDELINES COOKING GUIDELINES The guidelines given below are suggested quantities, temperature settings, and estimated numbers of orders per load and per hour. When two temperatures are given, the first is to start the product, and the second to finish the product.
COOKING GUIDELINES Gas Power Tilt Skillets PORTION SIZE TEMP.(°F) BATCHES PER HOUR GLTS-30 PER LOAD GLTS-40 PER LOAD QTY. PORTIONS QTY.
Gas Power Tilt Skillets ITEM PORTION SIZE COOKING GUIDELINES TEMP.(°F) BATCHES PER HOUR GLTS-30 PER LOAD GLTS-40 PER LOAD QTY. PORTIONS QTY.
TROUBLESHOOTING Gas Power Tilt Skillets TROUBLESHOOTING Burners No Not Come On 1. Gas supply to unit is “OFF”. 2. Manual shut off valve is “OFF”. 3. Thermostat is not turned “ON”. 4. Pan not in lowest position. 5. Ignition control not functioning. 6. Unit electrical supply is not plugged in or turned on. Burners Produce Carbon Deposits 1. Wrong size orifices. 2. Burner air not adjusted properly. 3. Wrong gas supply. 4. Incorrect pressure at supply.
Gas Power Tilt Skillets Notes INSTALLATION & OPERATION MANUAL 10100 REV 0 (04/21) PAGE 15 OF16
Gas Power Tilt Skillets GLTS-30 & GLTS-40 Gas Power Tilt Skillets A product with the Crown name incorporates the best in durability and low maintenance. We all recognize, however, that replacement parts and occasional professional service may be necessary to extend the useful life of this appliance. When service is needed, contact a Crown Authorized Service Agency, or your dealer. To avoid confusion, always refer to the model number, serial number, and type of your appliance.
