Installation Guide

ManualsBrandsCroydex ManualsBath26 in. x 20 in. Recessed or Surface Mount Medicine Cabinet in Aluminum with Hang 'N' Lock

Aluminium Cabinet

Thank you for purchasing this Croydex product. Please follow the xing and care instructions to ensure

your aluminium cabinet is tted safely and retains its high quality nish.

Please retain this leaet for future reference.

This installation guide applies to the following cabinets:

WC101169 - Aluminium Recessed & Surface Mounted Cabinet 405mm x 510mm (16” x 20”)

WC101269 - Aluminium Recessed & Surface Mounted Cabinet 380mm x 660mm (15” x 26”)

WC101369 - Aluminium Recessed & Surface Mounted Cabinet 510mm x 660mm (20” x 26”)

WC101469 - Aluminium Recessed & Surface Mounted Cabinet 610mm x 760mm (24” x 30”)

WC101569 - Aluminium Recessed & Surface Mounted Oval Cabinet 535mm x 785mm (21” x 31”)

WC101669 - Aluminium Recessed & Surface Mounted Bi-View Cabinet 760mm x 660mm (30” x 26”)

WC101769

- Aluminium Recessed & Surface Mounted Tri-View Cabinet 610mm x 660mm (24” x 26”)

WC101869 - Aluminium Recessed & Surface Mounted Tri-View Cabinet 760mm x 660mm (30” x 26”)

WC101969 - Aluminium Recessed & Surface Mounted Tri-View Cabinet 914mm x 660mm (36” x 26”)

WC102069 - Aluminium Recessed & Surface Mounted Bi-View Cabinet 610mm x 660mm (24” x 26”)

Tools required - not supplied

SURFACE MOUNTED

Pencil;Tape Measure; Philips Screwdriver; Flat Head Screwdriver; Spanner / Wrench (7mm); Drill; 8mm

Drill Bit, 11mm Drill Bit;(Ceramic drill bit optional).

RECESSED MOUNTED

Pencil;Tape Measure; Spirit Level; Hole Saw; Saw; Screwdriver; Stud and Power Cable Detector.

KEEP DIY TOOLS OUT OF THE REACH OF CHILDREN

Home Safety Advice

- It is recommended that two people t this product to ensure that it is tted safely.

- Always take care when using power tools, particularly in the bathroom.

- Always check for hidden cables and pipework before drilling and take extreme care if there is any

water in the working area.

- It is advisable to use a residual current circuit breaker (RCCB).

- Always wear suitable eye protection when drilling.

- If the product is to be tted on a ceramic tiled wall, a ceramic drill bit should be used.

- Always ensure that the drill hole passes through the central tiled area rather than through the grouted

area. To prevent damage to the tile, mask the area around the hole with tape before drilling.

- Do not strike the product with hard or sharp objects.

Product Care

To retain the best quality nish, clean product regularly with a soft damp cloth.

Do not use abrasive or chemical cleaners as these will damage the product.

CAB 075 R03

Summary of content (18 pages)

PAGE 1
EN Aluminium Cabinet Thank you for purchasing this Croydex product. Please follow the fixing and care instructions to ensure your aluminium cabinet is fitted safely and retains its high quality finish. Please retain this leaflet for future reference.
PAGE 2
ES Armario de aluminio Muchas gracias por adquirir este producto de Croydex. Siga las instrucciones que explican cómo fijar y mantener el armario para asegurarse de que esté instalado de manera segura y conserve sus acabados de alta calidad. Guarde este documento para futuras consultas.
PAGE 3
FR Armoire aluminium Nous vous remercions d’avoir acheté ce produit Croydex. Nous vous invitons à suivre les consignes d’installation et d’entretien afin d’être sûr que votre armoire est bien fixée et qu’elle conservera sa finition de qualité. Nous vous recommandons de conserver ce manuel afin de pouvoir vous y référer ultérieurement.
PAGE 4
Pack Contents (Not to scale) Contenido del embalaje (no está a escala) Contenu de l’emballage (dessin non à l’échelle) EN ES FR A. Hang ‘N’ Lock Bracket x 1 B. Hang ‘N’ Lock Bracket x 1 C. Hang ‘N’ Lock Spacer x 1 (2) (3) D. Hang ‘N’ Lock Spacer (Small) x 1 E. Hang ‘N’ Lock Cam x 2 F. Hang ‘N’ Lock Locking Stud x 2 Soporte Hang ‘N’ Lock x 1 Ferrure de fixation “Hang ‘N’ Lock” x 1 Separador Hang ‘N’ Lock (pequeño) x 1 Entretoise “Hang ‘N’ Lock” (petit modèle) x 1 G.
PAGE 5
Surface Mounting Assembly A (x1) F (x2) (If recess mounting the cabinet turn to page.
PAGE 6
Pre-installation guide for surface mounting the cabinet Guía de preinstalación para montar el armario en superficie Préparation de l’installation des armoires fixées au mur EN If the cabinet is to be surface mounted it is imperative that the 45 degree hanging profile is fitted to the cabinet prior to installation. Insert the 45 degree profile into the top of the cabinet and secure into position from each side of the cabinet.
PAGE 7
Fitting Hang ‘N’ Lock with countersink screws Colocación del soporte Hang ‘N’ Lock mediante pernos con cabeza de arpón Installation du système de fixation à l’aide des vis à tête fraisée EN Drill the marked holes to a depth of 45mm. Insert the wall plugs level with the surface of the wall.
PAGE 8
EN Drill the holes with an 11mm drill bit. (Note: If you are fitting the product to a tiled surface, a ceramic drill bit should be used.) Insert the treaded bolt through the Hang ‘N’ Lock cams and reattach the plugs and spring loaded braces onto the bolts from the back of the Hang ‘N’ Lock bracket. ES FR Taladre los orificios con una broca de 11 mm. (Nota: si va a colgar el armario sobre azulejos, tiene que utilizar la broca para superficies de cerámica.
PAGE 9
EN ES Use a philips screwdriver and spanner to fit the side mirror brackets onto the cabinet prior to hanging. Align the brackets with the corresponding holes on the cabinet and secure the brackets in position using the bolts and locking nuts provided. 9 Use un destornillador de estrella y una llave para colocar los soportes laterales del espejo en el armario antes de colgarlo.
PAGE 10
EN ES FR Remove the protective film on the mirror glass spacers to reveal the adhesive pads and locate in two positions on the sidewall of the cabinet (2 spacer per sidewall). Slide the mirror glass into the channels on the mirror brackets. Retire la película protectora de los separadores del espejo para revelar las almohadillas adhesivas y localizar dos posiciones en los laterales del armario (2 separadores por lateral). Introduzca el espejo por las guías de los soportes correspondientes.
PAGE 11
15 EN Once secured into position hide the unused recessed cabinet holes by using the small hole caps provided. ES Una vez colocado el armario en su posición, oculte los orificios que sirven para el montaje empotrado. Para ello, coloque los embellecedores suministrados en los orificios que no se utilizan. FR Une fois l’armoire installée, cacher les trous inutilisés à l’aide des petits caches de propreté fournis. EN Locate the shelf brackets into the holes situated on the sidewall of the cabinet.
PAGE 12
Recess Mounting Assembly Montaje empotrado Éléments pour montage encastré M (x4) J (x4) * K (x2) * N (x4) M (x4) Q (x4) * 10 glass shelf bracket (J) and 5 glass shelves (K) are supplied with the WC101669 & WC102069 Bi-View Cabinet. 18 glass shelf bracket (J) and 9 glass shelves (K) are supplied with the WC101769, WC101869 & WC101969 Tri-View Cabinet. * Con el armario de doble visión WC101669 y WC102069 se incluyen 10 soportes para los estantes de cristal (J) y 5 estantes de cristal (K).
PAGE 13
Installation Guide - Recess mounting the cabinet Guía de instalación - Montaje empotrado Guide d’installation – Armoire encastrée EN Position and tape the cabinet template in the desired location ensuring the template is level. Use a stud and cable detector to identify the location of wall studs and electric cables or cut a small hole within the boundary of the template to identify internal obstructions.
PAGE 14
EN Using the dotted line printed on the template cut out the aperture for the cabinet. 2 Cutout sizes for reference are as follows: WC101169 Cabinet - 360 mm (14.17”) x 461 mm (18.15”) WC101269 Cabinet - 360 mm (14.17”) x 623 mm (24.5”) WC101369 Cabinet - 487 mm (19.17”) x 623 mm (24.5”) WC101469 Cabinet - 589 mm (23.18”) x 725 mm (28.5”) WC101569 Oval Cabinet - 360 mm (14.17”) x 483 mm (19”) WC101669 Bi-View Cabinet - 751 mm (29.56”) x 623 mm (24.
PAGE 15
IMPORTANT: Pre-installation guide for WC101569 Oval Cabinet IMPORTANTE: Guía de preinstalación para montar el armario ovalado WC101569 IMPORTANT: Préparation de l’armoire ovale WC101569 EN Before installing the WC101569 Oval Cabinet it is important to fit the spacer extrusions behind the front flange of the cabinet. Simply peel off the tape and locate the spacer into position.
PAGE 16
6 EN Once secured into position hide the remaining un-used holes using the large and small hole caps provided. ES Una vez colocado el armario en su posición, oculte los orificios que no utilice con los embellecedores grandes y pequeños. FR Une fois l’armoire installée, cacher les trous inutilisés à l’aide des petits et des grands caches de propreté fournis. EN Locate the shelf brackets into the holes situated on the sidewall of the cabinet.
PAGE 17
Hinge Adjustment Guide for WC101169 Bisagra Guía de Ajuste por WC101169 Charnière Guide Ajustement pour WC101169 EN To move the door position forwards adjust as shown. ES Para mover la posición de la puerta hacia delante Ajuste según se muestra. FR Pour déplacer la position de la porte avant d’ajuster comme le montre. EN To move the door position up or down adjust as shown. ES Para mover la posición de la puerta hacia arriba o hacia abajo Ajuste según se muestra.
PAGE 18
Hinge Adjustment Guide Bisagra Guía de Ajuste Charnière Guide Ajustement EN To move the door position forwards adjust as shown. ES Para mover la posición de la puerta hacia delante Ajuste según se muestra. FR Pour déplacer la position de la porte avant d’ajuster comme le montre. EN To move the door position up or down adjust as shown. ES Para mover la posición de la puerta hacia arriba o hacia abajo Ajuste según se muestra.