User`s manual
2
INSTALLLATON
WHERE AND HOW TO MOUNT YOUR MOBILE CB RADIO
1.
a)You should choose the most appropriate setting from a simple and
practical point of view.
b)Your CB radio should not interfere with the driver or the passengers.
c) Remember to provide different wires for passing and protection.
(e.g.: power, antenna, accessory cabling) so that they do not in any
way interfere with the driving of vehicles.
d)To install your equipment, use the cradle (1) and the self-tapping
screws [2] provided (drilling diameter 5 mm). Take care not to
damage the vehicle’s electrical system while drilling the dash
board.
e)Do not forget to insert the rubber joints [3] between the CB and
its support as these have a shock-absorbing effect which permits
gentle orientation and tightening of the set.
f)Choose where to place the microphone support and remember that
the microphone cord must stretch to the driver without interfering
with the controls of the vehicle.
ANTENNA INSTALLATION
2.
a) Choosing your antenna:
For CB radios, the longer the antenna, the better its results. Your
dealer will help you with your choice of antenna.b) Antena Movel.
b) Mobile antenna:
-Must be xed to the vehicle where there is a maximum of metallic
surface(ground plane) , away from windscreen mountings.
-There are two types of antenna: Pre-Regulated Antenna which
should be used on a good ground plane (e.g. car roof or lid of the
boot), and Adjustable Antenna which offer a much larger frequency
range and can be used on a smaller ground plane.
For an antenna which must be fixed by drilling, you will need a
good contact between the antenna and the ground plane. To obtain
this, you should lightly scratch the surface where the screw and
tightening star are to be placed.
-Be careful not to pinch or atten the coaxial cable (as this runs the
risk of break down and/or short circuiting).
-Connect the antenna to location (B).
c) Fixed antenna:
A xed antenna should be installed in a space as clear as possible.
If it is fixed to a mast, it will perhaps be necessary to stay it,
according to the laws in force (you should seek professional
advice). All SS 6900 antennas and accessories are designed to
give maximum efciency to each CB radio within the range.
1
FUNCTIONS & FEATURES
Big LCD which displays frequency and all kinds of information
1.
DUAL-DIGITAL TUBE FOR CHANNEL DISPLAY
2.
USE EL technology for backlight
3.
PA
4.
、
CW
、
AM
、
FM
、
USB
、
LSB mode
A
5.
、
B
、
C
、
D
、
E
、
F , 6 bands in total, with 60 channels at most in
each band to be programmed.
Frequency Tuning Step can be 10HZ, 100HZ, 1KHZ or 10KHZ.
6.
Multiple CLARIFIER Operating Modes
7.
Flexible menu functions and PC programming software to meet
8.
varied customer demands
ECHO Function
9.
SQ, ASQ Function (FM and AM mode only)
10.
RF GANI ADJUSTMENT
11.
RF PWR ADJUSTMENT
12.
SCAN FUNCTION
13.
RB FUNCTION
14.
NB/ANL FUNCTION
15.
DW DUAL-WATCH FUNCTION
16.
BEEP VOICE PROMPT
17.
+10KHZ Function
18.
SWR
19.
、
S/RF
、
DC Voltage display function
TOT function
20.
HI-CUT FUNCTION
21.
EMG CALL
22.
SWR PROTECTION
23.
POWER SUPPLIED VOLTAGE PROTACTION
24.
Key-Lock Function
25.
WARNIGN
To use the radio, please connect the antenna to the location "B" on the
back panel of the equipment firstly and then set the SWR (Standing
Wave Ratio) before transmitting. Failure to do so may result in
destruction of the power amplier, which is not covered by the guarantee.
RESET FUNCTION (Resume Factory Default)
This CB Radio introduces RESET FUNCTION to prevent accidents
and provide a solution for customers who changed some functions
unconsciously and do not know how to resume normal settings. The CB
Radio will resume factory default once this function is activated.
How to Operate:
Step 1: Power off the radio.
Step 2: Press and hold FUNC and SCAN keys at the same time,
followed by powering on the radio.
Step3: Release the two keys when LCD displays "RES".
All former settings would be replaced by Factory Default value when
LCD displays "REND" .
WARNING: All former settings would be replaced by Factory Default
value after operating the RESET FUNCTION.
TX