Specifications

RTX220 QR - Manual
RTX
™
430-3QR Quick Start Guide
1. Installation Steps
1.1 Hard Drive Installation
a. Pull the ejection handle on the TrayFree bay to
open the bay door.
b. Insert a SATA hard drive into the bay.
Make sure it is label-side up with the SATA
connection on the drive inserted rst toward
the rear of the enclosure.
c. Shut the bay door.
1.2 Connecting and Powering the RTX430-3QR
The RTX430-3QR has one USB2.0/3.0 port, one eSATA port, two FireWire 800 ports, and one
conguration switch on the rear of the unit.
a. Choose one of the connection types and connect the applicable cable from your computer to the
corresponding port on the RTX enclosure.
b. Connect the power cord to the unit and the other end to a grounded electrical outlet.
c. If you’re using USB, make sure the USB Mode Switch is set to USB 2.0 or 3.0 to match the USB
connection type used to connect the RTX enclosure to your computer.
d. With the hard drives in the unit, ip the power switch to turn on the RTX enclosure.
Technical Specications, continued...
Operating Temperature 86 – 104° Fahrenheit (30 – 40° Celsius)
Operating Humidity 5% to 95%, non-condensing
Power Switch 2 position: On / Off
Power Supply Input: 100-240VAC
Output: 120 Watts
Torque 3.5-inch hard drives, #6-32 screws: 6 inch-pounds max.
Compliance EMI Standard: FCC Part 15 Class A, CE
EMC Standard: EN55022, EN55024
Shipping Weight 13 pounds (without drives)
18 pounds (with drives)
Product Dimensions 10.63” x 6.89” x 7.87” (270mm x 175mm x 200mm)
Technical Support Contact us at www.cru-dataport.com/support. We also offer phone support at (800)
260-9800 or [phone].
RAX is a trademark of CRU Acquisitions Group, LLC. Other marks are the property of their respective owners. © 2010 CRU Acquisitions Group, LLC.
All rights reserved.
Limited Product Warranty
CRU-DataPort (CRU) warrants RAX to be free of signicant defects in material and workmanship for a period of three years from the original date of
purchase. CRU’s warranty is nontransferable and is limited to the original purchaser.
Limitation of Liability
The warranties set forth in this agreement replace all other warranties. CRU expressly disclaims all other warranties, including but not limited to, the
implied warranties of merchantability and tness for a particular purpose and non-infringement of third-party rights with respect to the documentation
and hardware. No CRU dealer, agent, or employee is authorized to make any modication, extension, or addition to this warranty. In no event will CRU
or its suppliers be liable for any costs of procurement of substitute products or services, lost prots, loss of information or data, computer malfunction,
or any other special, indirect, consequential, or incidental damages arising in any way out of the sale of, use of, or inability to use any CRU product or
service, even if CRU has been advised of the possibility of such damages. In no case shall CRU’s liability exceed the actual money paid for the products
at issue. CRU reserves the right to make modications and additions to this product without notice or taking on additional liability.
FCC Compliance Statement: “This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.”
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at this own expense.
In the event that you experience Radio Frequency Interference, you should take the following steps to resolve the problem:
1) Ensure that the case of your attached drive is grounded.
2) Use a data cable with RFI reducing ferrites on each end.
3) Use a power supply with an RFI reducing ferrite approximately 5 inches from the DC plug.
4) Reorient or relocate the receiving antenna.
A9-430-0001-1 Rev. 1.0
For the full user manual and more information about this product, visit www.cru-dataport.com.
Models Covered:
RTX430-3QR
FOR OFFICE OR COMMERCIAL USE