Datasheet

ManualsBrandsCrucial Manualscomputers & electronicsMTFDDAA120MBB2AE1ZAB

M500DC 1.8-Inch SATA NAND Flash SSD

MTFDDAA120MBB-2AE1ZABYY, MTFDDAA240MBB-2AE1ZABYY,

MTFDDAA480MBB-2AE1ZABYY, MTFDDAA800MBB-2AE1ZABYY

Features

• Micron

20nm MLC NAND Flash

• RoHS-compliant package

• SATA 6 Gb/s interface

• ATA modes supported

– PIO mode 3, 4

– Multiword DMA mode 0, 1, 2

– Ultra DMA mode 0, 1, 2, 3, 4, 5

• Enterprise sector size support

– 512-byte

• Hot-plug capable

• Native command queuing support with 32-com-

mand slot support

• ATA-8 ACS2 command set compliant

• ATA security feature command set and password

• Security erase command set: fast and secure erase

• Self-monitoring, analysis, and reporting technology

(SMART) command set

• 120GB performance (steady state)

1, 2

– Sequential 128KB read: 425 MB/s

– Sequential 128KB write: 200 MB/s

– Random 4KB read: 63,000 IOPS

– Random 4KB write: 23,000 IOPS

– READ latency: 0.50ms

– WRITE latency: 1.5ms

• 240GB performance (steady state)

1, 2

– Sequential 128KB read: 425 MB/s

– Sequential 128KB write: 330 MB/s

– Random 4KB read: 63,000 IOPS

– Random 4KB write: 33,000 IOPS

– READ latency: 0.50ms

– WRITE latency: 1.5ms

• 480GB performance (steady state)

1, 2

– Sequential 128KB read: 425 MB/s

– Sequential 128KB write: 375 MB/s

– Random 4KB write: 63,000 IOPS

– Random 4KB write: 35,000 IOPS

– READ latency: 0.50ms

– WRITE latency: 1.5ms

• 800GB performance (steady state)

1, 2

– Sequential 128KB read: 425 MB/s

– Sequential 128KB write: 375 MB/s

– Random 4KB read: 65,000 IOPS

– Random 4KB write: 24,000 IOPS

– READ latency: 0.50ms

– WRITE latency: 1.5ms

• Reliability

– Mean time to failure (MTTF): 2 million device

hours

– Static and dynamic wear leveling

– Uncorrectable bit error rate (UBER): <1 sector

per 10

bits read

• Endurance: Total bytes written (TBW)

– 120GB: 0.5PB; 240GB: 1.0PB; 480GB: 1.9PB;

800GB: 1.9PB

• Capacity

(unformatted): 120GB, 240GB, 480GB,

800GB

• Mechanical: 5.0mm height

– Micro SATA connector: 3.3V ±5%

– 1.8-inch drive: 78.5mm x 54mm x 5mm

• Field-upgradeable firmware

• Power consumption: <6.0W (TYP); <6.3W (TYP) for

800GB

• Operating temperature

– Commercial (0°C to 70°C)

Notes:

1. Typical I/O performance numbers as meas-

ured using Iometer with a queue depth of

32 and write cache disabled.

2. 4KB transfers used for READ/WRITE latency

values.

3. The product achieves a MTTF based on pop-

ulation statistics not relevant to individual

units.

4. 1GB = 1 billion bytes; formatted capacity is

less.

5. Drive case temperature.

Warranty: Contact your Micron sales representative

for further information regarding the product,

including product warranties.

M500DC 1.8-Inch NAND Flash SSD

Features

PDF: 09005aef854f62f9

M500DC_1_8_disti.pdf - Rev. D 4/14 EN

Micron Technology, Inc. reserves the right to change products or specifications without notice.

Products and specifications discussed herein are subject to change by Micron without notice.

Summary of content (30 pages)

PAGE 1
M500DC 1.8-Inch NAND Flash SSD Features M500DC 1.8-Inch SATA NAND Flash SSD MTFDDAA120MBB-2AE1ZABYY, MTFDDAA240MBB-2AE1ZABYY, MTFDDAA480MBB-2AE1ZABYY, MTFDDAA800MBB-2AE1ZABYY Features • • • • • • • • • • • • • • • 800GB performance (steady state) 1, 2 – Sequential 128KB read: 425 MB/s – Sequential 128KB write: 375 MB/s – Random 4KB read: 65,000 IOPS – Random 4KB write: 24,000 IOPS – READ latency: 0.50ms – WRITE latency: 1.
PAGE 2
M500DC 1.8-Inch NAND Flash SSD Features Part Numbering Information Micron’s M500DC SSD is available in different configurations and densities. Visit micron.com for a list of valid part numbers. Figure 1: Part Number Chart MT FD D AA 120 M BB - 2 AE 1 Z AB YY ES Micron Technology Production Status Product Family Blank = Production ES = Engineering sample FD = Flash drive Customer Designator YY = Standard Drive Interface D = SATA 6.
PAGE 3
M500DC 1.8-Inch NAND Flash SSD General Description General Description Micron’s M500DC solid state drive (SSD) uses a single-chip controller with a SATA interface on the system side and n-channels of Micron NAND Flash internally. Packaged in an HDD replacement enclosure, the SSD integrates easily in existing storage infrastructures.
PAGE 4
M500DC 1.8-Inch NAND Flash SSD Logical Block Address Configuration Logical Block Address Configuration The drive is set to report the number of logical block addresses (LBA) that will ensure sufficient storage space for the specified density. Standard LBA settings, based on the IDEMA standard (LBA1-02), are shown below.
PAGE 5
M500DC 1.8-Inch NAND Flash SSD Interface Connectors Interface Connectors The SATA signal segment interface cable has four conductors and three ground connections. As shown in Package Dimensions, the cable includes a 7-pin signal segment and a 9-pin power segment arranged in a single row with a 1.27mm (0.050in) pitch.
PAGE 6
M500DC 1.
PAGE 7
M500DC 1.
PAGE 8
M500DC 1.
PAGE 9
M500DC 1.
PAGE 10
M500DC 1.
PAGE 11
M500DC 1.
PAGE 12
M500DC 1.
PAGE 13
M500DC 1.
PAGE 14
M500DC 1.
PAGE 15
M500DC 1.
PAGE 16
M500DC 1.
PAGE 17
M500DC 1.
PAGE 18
M500DC 1.
PAGE 19
M500DC 1.
PAGE 20
M500DC 1.
PAGE 21
M500DC 1.8-Inch NAND Flash SSD Device ID Table 5: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 222 Default Value Description – – – 15–12 – 0001b 11–7 – 000000b 6 – 1b 1 = SATA rev 3.1 is supported 5 – 1b Reserved SATA rev 3.0 4 – 1b Reserved SATA rev 2.6 3 – 1b Reserved SATA rev 2.5 2 – 1b Reserved SATA II: Extensions 1 – 1b Reserved SATA 1.
PAGE 22
M500DC 1.
PAGE 23
M500DC 1.
PAGE 24
M500DC 1.8-Inch NAND Flash SSD Performance Performance Measured performance can vary for a number of reasons. The major factors affecting drive performance are the density of the drive and the interface of the host. Additionally, overall system performance can affect the measured drive performance. When comparing drives, it is recommended that all system variables are the same, and only the drive being tested varies. Performance numbers will vary depending on the host system configuration.
PAGE 25
M500DC 1.8-Inch NAND Flash SSD Reliability Mean Time to Failure Mean time to failure (MTTF) for the SSD can be predicted based on the component reliability data using the methods referenced in the Telcordia SR-332 reliability prediction procedures for electronic equipment. Table 9: MTTF MTTF (Operating Hours)1 Density 120GB 2 million 240GB 2 million 480GB 2 million 800GB 2 million Note: 1.
PAGE 26
M500DC 1.8-Inch NAND Flash SSD Electrical Characteristics Electrical Characteristics Stresses greater than those listed may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
PAGE 27
M500DC 1.
PAGE 28
M500DC 1.8-Inch NAND Flash SSD Package Dimensions Package Dimensions Figure 4: 1.8-Inch Package – 5mm 54.00mm ±0.25 2.126in ±0.010 54.00mm ±0.25 2.126in ±0.010 78.50mm ±0.60 3.091 in ±0.024 0.50mm (MAX) 0.020in (MAX) 78.50mm ±0.60 3.091in ±0.024 0.50mm (MAX) 0.020in (MAX) 3.00mm 0.118in (2 PLCS) 3.00mm 0.118in (2 PLCS) 3.30mm ±0.35 0.130in ±0.014 (2 PLCS) CL Drive and connector center PDF: 09005aef854f62f9 M500DC_1_8_disti.pdf - Rev. D 4/14 EN A 3.85mm 0.151in CL 1.35mm 0.
PAGE 29
M500DC 1.8-Inch NAND Flash SSD References Figure 5: Thermocouple Placement Guidelines for Temperature Measurement 31 (1.2in) 3mm 3mm 27 (1.1in) 3mm 3mm References • Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available at www.sata-io.org • SATA 3.1 GOLD • ATA-8 Rev. 4 PDF: 09005aef854f62f9 M500DC_1_8_disti.pdf - Rev. D 4/14 EN 29 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc.
PAGE 30
M500DC 1.8-Inch NAND Flash SSD Revision History Revision History Rev. D – 4/14 • • • • Status changed to Production. Updated Table 5: Identify Device Updated note 2 in Table 11: SATA Power Consumption Revised operating vibration specification • • • • Updated part numbers Revised performance specifications Updated package dimensions drawing Updated device ID values Rev. C – 3/14 Rev. B – 11/13 • Revised performance specifications Rev. A – 8/13 • Initial release 8000 S. Federal Way, P.O.