Datasheet

ManualsBrandsCrucial Manualscomputers & electronicsMTFDGAR1T4MAX-1AG1ZABYY

P420m Half-Height and Half-Length PCIe

NAND Flash SSD

MTFDGAR1T4MAX, MTFDGAR700MAX

Features

• Micron

25nm MLC NAND Flash

• ONFI 2.1-compliant Flash interface

• PCIe Gen2 x8 host interface

• Capacity:

700GB, 1.4TB

• Endurance (total bytes written)

2,3

– 700GB: 4.6PB (4KB random write),

9.7PB (128KB sequential write)

– 1.4TB: 9.2PB (4KB random write),

19.5PB (128KB sequential write)

• Temperature

– Operating: 0°C to +85°C

– Storage (in system): 0°C to +40°C

– Storage (on shelf): –40°C to +85°C

– Temperature throttling support

• ATA modes supported

– PIO modes 3 and 4

– Multiword DMA modes 0, 1, 2

– Ultra DMA modes 0, 1, 2, 3, 4, 5, 6

– ATA8-ACS2 command set support

– ATA security feature command set and password

• Industry-standard 512-byte sector size support

• Full end-to-end data protection

• Native command queuing up to 256 commands

• Bootable

• Power

– 700GB: 25W RMS

– 1.4TB: 25W RMS

• Random read/write (steady state) performance

– Random read: Up to 750,000 IOPS (4KB IO size)

– Random write: Up to 95,000 IOPS (4KB IO size)

– Random read/write (70/30) mixed workload:

Up to 220,000 IOPS (4KB IO size)

• Sequential read/write (steady state) performance

– Sequential read: Up to 3.3 GB/s (128KB IO size)

– Sequential write: Up to 630 MB/s (128KB IO size)

• Latency (queue depth 1)

– READ latency: <100µs (MIN)

– WRITE latency: 13µs (posted) (MIN)

• Custom drivers

– Windows Server 2012 R2 (x86-64), Hyper-V

(x86-64)

– Windows Server 2012 (x86-64), Hyper-V (x86-64)

– Windows Server 2008 R2 SP1 (x86-64), Hyper-V

(x86-64)

– Windows 8, 8.1 (x86-64 and x86)

– Windows 7 (x86-64 and x86)

– RHEL 5.5–5.10, 6.0–6.5, 7 (x86-64)

– SLES 11 SP1, SP2, SP3 (x86-64)

– VMware 5.0, 5.1 (x86-64)

– VMware 5.5 (inbox driver)

– Citrix XenServer 6.0.2, 6.1, 6.2

– Ubuntu 12.04–12.04.4, 14.04 LTS Server (64-bit)

• Reliability

– MTTF: 2.0 million hours

– Static and dynamic wear leveling

– Field-upgradable firmware

– Uncorrectable bit error rate (UBER): <1 sector

per 10

bits read

– Power holdup protection for MLC NAND

• Micron redundant array of independent NAND

(RAIN) technology

• SMART command set support

• On-chip temperature monitoring

• Mechanical/electrical

– Half-height, half-length form factor: 68.90mm x

167.65mm x 18.71mm

– PCIe-compliant, x8 lane PCB connector

– Weight: 700GB – 199.59g; 1.4TB – 204.12g

– 12V power (±8%)

• Shock (nonoperational): 400g at 2ms half-sine,

150g at 10ms half-sine

• Vibration (nonoperational): 3.1 grms 5–800Hz at

30 min/axis

• RoHS compliant

Notes:

1. User capacity: 1GB = 1 billion bytes.

2. Lifetime endurance is measured not in

years, but in the number of bytes that can

be written to the device.

3. Workloads are 100% writes.

4. Operating temperature is the drive case

temperature as measured by the SMART

temperature attribute.

5. Assumes system is powered off and ready to

be powered on.

P420m HHHL PCIe NAND SSD

Features

PDF: 09005aef853f2344

p420m_hhhl.pdf - Rev. O 8/2014 EN

Micron Technology, Inc. reserves the right to change products or specifications without notice.

Products and specifications discussed herein are subject to change by Micron without notice.

Summary of content (20 pages)

PAGE 1
P420m HHHL PCIe NAND SSD Features P420m Half-Height and Half-Length PCIe NAND Flash SSD MTFDGAR1T4MAX, MTFDGAR700MAX Features • • • • • • • • • • • • • • • • Micron® 25nm MLC NAND Flash ONFI 2.1-compliant Flash interface PCIe Gen2 x8 host interface Capacity:1 700GB, 1.4TB Endurance (total bytes written)2,3 – 700GB: 4.6PB (4KB random write), 9.7PB (128KB sequential write) – 1.4TB: 9.2PB (4KB random write), 19.
PAGE 2
P420m HHHL PCIe NAND SSD Features 6. Bootable option determined by part number; see Part Numbering Information (page 3). Boot ability may not be compatible with some systems. 7. Power is 30W RMS with power limiting disabled. 8. Varies by capacity. See Performance Specifications (page 5) for details. PDF: 09005aef853f2344 p420m_hhhl.pdf - Rev. O 8/2014 EN 2 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved.
PAGE 3
P420m HHHL PCIe NAND SSD Features Part Numbering Information The Micron® P420m SSD is available in different configurations and capacities. Visit www.micron.com for a list of valid part numbers.
PAGE 4
P420m HHHL PCIe NAND SSD General Description General Description Micron's P420m SSD is targeted at applications that require high performance and enterprise-class storage reliability. The P420m delivers extremely high IOPS performance due to its ability to support up to 256 outstanding commands while ensuring full endto-end data protection. The P420m comes in a half-height, half-length (HHHL) form factor and uses a secondgeneration (Gen2) PCIe x8 lane interface on the host side and 32 ONFI 2.
PAGE 5
P420m HHHL PCIe NAND SSD Architecture Architecture The single-chip, Micron-developed ASIC controller, along with the host and Flash interfaces, provide an embedded ATA host bus adapter, a host/Flash translation layer, Flash maintenance, channel control, and Flash RAID (RAIN) protection. Flash endurance and reliability are optimized through the Flash maintenance features, including static and dynamic wear leveling and RAIN protection.
PAGE 6
P420m HHHL PCIe NAND SSD Functional Description Functional Description Data Retention Data retention refers to the SSD's media (NAND Flash) capability to retain programmed data when the SSD is powered off. The two primary factors that influence data retention are degree of use (the number of PROGRAM/ERASE cycles on the media) and temperature. The SSD provides power-off data retention of two months at 40°C (MAX) when total bytes written (TBW) is reached.
PAGE 7
P420m HHHL PCIe NAND SSD SMART Attribute Summary SMART Attribute Summary Table 3: SMART Command Reference Attribute ID Hex ID Name SMART Trip Description 9 0x09 Power-on hours count No Lifetime powered-on hours, from the time the device leaves the factory 12 0x0C Power cycle count No Count of power cycles 170 0xAA New failing block count No Grown defects 171 0xAB Program fail count No Number of NAND program status failures 172 0xAC Erase fail count No Number of NAND erase statu
PAGE 8
P420m HHHL PCIe NAND SSD Logical Block Address Configuration Logical Block Address Configuration The number of logical block addresses (LBAs) reported by the P420m ensures sufficient storage space for the specified capacity. Standard LBA settings based on the IDEMA standard (LBA1-02) are shown below. Table 4: Standard LBA Settings Total LBA Capacity Decimal Hexadecimal Decimal Hexadecimal User Available Bytes Unformatted 700GB 1,367,473,968 5181FF30 1,367,473,967 5181FF2F 700,146,671,616 1.
PAGE 9
P420m HHHL PCIe NAND SSD Interface Connectors Interface Connectors The host interface connector conforms to the PCIe Electromechanical Specification V2.0, section 5, Table 5-1. It is a four-lane, gold-finger connector with 1mm pitch spacing. A mechanical indent is used to separate the PCIe power pins from the differential signal contacts. The pins are numbered below in ascending order from left to right. Side B refers to component side and Side A refers to the solder side.
PAGE 10
P420m HHHL PCIe NAND SSD Interface Connectors Table 6: PCIe Interface Connector Pin Assignments (Continued) Side B Side A Pin Number Name Description Name Description 30 RSVD Reserved PERn3 PCIe RX Lane 3 n 31 PRSNT2# Hot Plug Presence Detect GND Ground 32 GND Ground RSVD Reserved 33 PETp4 PCIe TX Lane 4 p RSVD Reserved 34 PETn4 PCIe TX Lane 4 n GND Ground 35 GND Ground PERp4 PCIe RX Lane 4 p 36 GND Ground PERn4 PCIe RX Lane 4 n 37 PETp5 PCIe TX Lane 5 p GND Gro
PAGE 11
P420m HHHL PCIe NAND SSD PCIe Header PCIe Header Figure 3: PCIe Header Byte offset 0 31 Device ID = 5161h Vendor ID = 1344h 00h Status Command 04h Class code = 018000h BIST Header type = 00h Master latency timer Revision ID = 03h 08h Cache line size 0Ch ~ ~ ~ ~ Subsystem ID = 22xxh (700GB) Subsystem ID = 32xxh (1.4TB) Note: PDF: 09005aef853f2344 p420m_hhhl.pdf - Rev. O 8/2014 EN Subsystem vendor ID = 1344h 2Ch 1. Standard Distribution Subsystem ID is 2200h for 700GB and 3200h for 1.4TB.
PAGE 12
P420m HHHL PCIe NAND SSD Commands Commands Table 7: Supported ATA Command Set See ATA–8 ACS–2 specification for command details Commands ATA Protocol CMD Code Feature Codes CHECK POWER MODE ND 0xE5 – DEVICE CONFIGURATION FREEZE LOCK ND 0xB1 0xC1 DEVICE CONFIGURATION IDENTIFY PI 0xB1 0xC2 DEVICE CONFIGURATION RESTORE ND 0xB1 0xC0 DEVICE CONFIGURATION SET PO 0xB1 0xC3 DOWNLOAD MICROCODE PO 0x92 – EXECUTE DEVICE DIAGNOSTIC DD 0x90 – FLUSH CACHE ND 0xE7 – FLUSH CACHE EXT ND
PAGE 13
P420m HHHL PCIe NAND SSD Commands Table 7: Supported ATA Command Set (Continued) See ATA–8 ACS–2 specification for command details Commands ATA Protocol CMD Code Feature Codes SEEK ND 0x7x – SET FEATURES ND 0xEF VARIOUS SET MAX ADDRESS ND 0xF9 0x00 SET NATIVE MAX ADDRESS EXT ND 0x37 – SET MAX SET PASSWORD ND 0xF9 0x01 SET MAX LOCK ND 0xF9 0x02 SET MAX FREEZE LOCK ND 0xF9 0x04 SET MAX UNLOCK ND 0xF9 0x03 SET MULTIPLE MODE ND 0xC6 – SLEEP ND 0xE6 – SMART DISABLE OPER
PAGE 14
P420m HHHL PCIe NAND SSD Reliability Reliability Micron’s SSDs incorporate advanced technology for defect and error management. They use various combinations of hardware-based error correction algorithms and firmware-based static and dynamic wear-leveling algorithms. Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is defined as data that is reported as successfully programmed to the SSD but when it is read out of the SSD, the data differs from what was programmed.
PAGE 15
P420m HHHL PCIe NAND SSD Reliability Power Holdup Protection If power is interrupted at any time while data is being programmed into the NAND, it is possible that data loss may occur and the MLC NAND's lower page may become corrupted. This can cause drive errors to be reported to the host.
PAGE 16
P420m HHHL PCIe NAND SSD Electrical Characteristics Electrical Characteristics Stresses greater than those listed may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
PAGE 17
P420m HHHL PCIe NAND SSD Compliance Compliance The device complies with the following specifications: • • • • • • • • • • • • • RoHS - Restriction of Hazardous Substances China RoHS WEEE Waste Electric and Electronic Equipment Halogen Free - meets IPC low-halogen requirements CE (Europe) EN55022/EN55024 (Class A) TUV (Germany) EN60950 UL (US/Canada) EN60950 FCC (US) 47CFR Part 15 Class A BSMI (Taiwan) CNS 13438 Class A VCCI (Japan) EN 55022/CISPR 22 Class A C-TICK (AUS/NZ) CISPR22 ICES (Canada) CISPR22 Cl
PAGE 18
P420m HHHL PCIe NAND SSD Drive Dimensions Drive Dimensions Figure 4: Half-Height, Half-Length Dimensions ( 1.04mm ) 0.041in (REF) 64.27mm ±0.13 2.530in ±0.005 4.85mm 0.191in 167.52mm ±0.13 6.595in ±0.005 11.65mm 0.459in DIA SLOT THRU 3.65mm 0.144 in 53.90mm 2.122in 68.77mm ±0.13 2.707in ±0.005 8.25mm 0.325in (3 PLCS) 1.90mm ±0.06 0.075in ±0.002 DIA SLOT THRU 12.15mm 0.478in 49.65mm 1.955in 8.53mm 0.336in 14.49mm 0.570in (MAX) 39.15mm 1.541in 15.00mm 0.591in 57.15mm 2.250in 1.04mm 0.
PAGE 19
P420m HHHL PCIe NAND SSD Revision History Revision History Rev. O – 08/14 • Updated custom drivers status. Rev. N – 07/14 • Changed documentation status Rev. M – 07/14 • Updated custom drivers list Rev. L – 03/14 • Updated Compliance section Rev. K – 02/14 • Updated Compliance section Rev. J – 01/14 • Updated 12V power range Rev. I – 01/14 • Updated custom drivers list Rev.
PAGE 20
P420m HHHL PCIe NAND SSD Revision History Rev. C – 7/13 • Updated note 3 in Performance Specifications section Rev. B – 6/13 • Updated performance and latency specifications Rev. A – 6/13 • Initial release; Preliminary status 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-4000 www.micron.com/products/support Sales inquiries: 800-932-4992 Micron and the Micron logo are trademarks of Micron Technology, Inc. All other trademarks are the property of their respective owners.