Datasheet

ManualsBrandsCRYDOM ManualsContactorsDR2220D20U

DR22 Series

DC Output DIN Rail Mount SSRs

• Output ratings up to 30 Amps at 200 VDC

• Integral heat sink eliminates the need for complex thermal calculations

• DBC substrate for superior thermal performance

• LED input status indicator

• IP20 touch-safe housing

• 1kHz Maximum PWM Frequency

• 3750 VAC optical isolation

• C-UL-US approved

PRODUCT SELECTION

Control Voltage 20A

4-32 VDC DR2220D20U

30A

DR2220D30U

AVAILABLE OPTIONS

Required for valid part number

Operating Voltage

20: 1-200 VDC

Control Voltage

D: 4-32 VDC

Series

DR22 20 D

Rated Load Current

20: 20 Amps

30: 30 Amps

Terminal Layout

U: Relay Configuration

OUTPUT SPECIFICATIONS

(1)

Description 30A

Absolute Maximum Rating [VDC] 200

Recommended Operating Voltage [VDC] 1-150

Maximum Off-State Leakage Current @ Rated Voltage [mA] 0.2

Load Current, DC General Use UL508 @ 40°C [ADC] 30

Minimum Load Current [mA]

(2) 5

Maximum Surge Current [ADC] (10ms) 86

Maximum On-State Voltage Drop @ Rated Current [VDC] 0.480

Maximum On-State Resistance [RDS-ON][Ohms] 0.016

Maximum Pulse Width Modulation Frequency [Hz]

(3) 900

20A

200

1-150

0.1

Load Current, DC Motor Starting UL508 FLA @ 40°C [ADC] 5.4

4.1

0.680

0.034

1000

Motor Rating UL 508 [HP (kW)]: 120 VDC 1/2 (0.37)

1/3 (0.25)

INPUT SPECIFICATIONS

(1)

Description

Control Voltage Range

Maximum Reverse Voltage

Minimum Turn-On Voltage (4)

Must Turn-Off Voltage

Minimum Input Current (for on-state)

Maximum Input Current

Nominal Input Impedance

Maximum Turn-On Time [µsec]

Maximum Turn-Off Time [µsec]

DC Control

4-32 VDC

-32 VDC

4 VDC

1 VDC

11 mA

15 mA

Current Regulated

100

Datasheet

DIN Rail Mount

Do not forget to visit us at: www.crydom.com

Summary of content (6 pages)

PAGE 1
DIN Rail Mount Datasheet DR22 Series DC Output DIN Rail Mount SSRs • Output ratings up to 30 Amps at 200 VDC • Integral heat sink eliminates the need for complex thermal calculations • DBC substrate for superior thermal performance • LED input status indicator • IP20 touch-safe housing • 1kHz Maximum PWM Frequency • 3750 VAC optical isolation • C-UL-US approved PRODUCT SELECTION Control Voltage 4-32 VDC 20A 30A DR2220D20U DR2220D30U AVAILABLE OPTIONS Series DR22 Operating Voltage 20: 1-200 VDC 20
PAGE 2
DIN Rail Mount Datasheet GENERAL SPECIFICATIONS (1) Description Parameters Dielectric Strength, Input to Output (50/60Hz) Dielectric Strength, Input/Output to Case (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Housing Material Heat Sink Material Din Rail Clip Material Hardware Finish Input Terminal Screw Torque Range (in-lb/Nm) Load Terminal Screw Torque Range (in-lb/Nm) Humidity
PAGE 3
DIN Rail Mount Datasheet THERMAL DERATE INFORMATION DR2220D20U Single unit (5) DR2220D30U Single unit (5) Multiple units 15 10 5 0 Multiple units 30 Load Current (Amps) Load Current (Amps) 20 20 30 40 50 60 Ambient Temperature (ºC) 70 25 20 15 10 5 0 80 20 30 40 50 60 Ambient Temperature (ºC) 70 80 EQUIVALENT CIRCUIT BLOCK DIAGRAMS/WIRING DIAGRAM Load can be wired in position A or B inductive loads must be diode suppressed.
PAGE 4
DIN Rail Mount Datasheet ACCESSORIES Recommended Accessories ID Marker CNLB CNLN CNL2 AGENCY APPROVALS, CONFORMANCES AND EMC E116949 Certification in accordance with: Certification in accordance with: United States Standard for Industrial Control Equipment - UL 508 and Canadian Standard Association for Industrial Control Equipment – C22.2 No. 14.
PAGE 5
DIN Rail Mount Datasheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo.
PAGE 6
DIN Rail Mount Datasheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.