Datasheet

ManualsBrandsCRYDOM ManualsContactorsDR2260D30U

DR22 Series

AC Output DIN Rail Mount SSRs

• Output ratings up to 35 Amps at 600 VAC

• Built-in overvoltage protection

• Relay or Contactor configuration

• Integral heat sink eliminates the need for complex thermal calculations

• DBC substrate for superior thermal performance

• "Elevator" screw option to allow the use of ring or lug type terminals

• IP20 touch-safe housing

• AC or DC control

• C-UL-US and TUV approved

PRODUCT SELECTION

Control Voltage 20A

90-280 VAC/VDC DR2260A20x

4-32 VDC DR2260D20x

30A

DR2260A30x

DR2260D30x

35A

DR2260A35x

DR2260D35x

AVAILABLE OPTIONS

Required for valid part number

For options only and not required for valid part number

Operating Voltage

60: 48-600 VAC

Switching Type

Blank: Zero Voltage Turn-On

R: Instantaneous Turn-On

(Motor Rating Certified)

Control Voltage (1)

A: 90-280 VAC/VDC

D: 4-32 VDC

Series

DR22 60 A R

Rated Load Current

20: 20 Amps

30: 30 Amps

35: 35 Amps [High I

Terminal Layout

U: Relay Configuration

V: Contactor Configuration

(std. screw)

W: Contactor Configuration

(elevator screw)

Input Connector

Blank: Screw Terminal

J: Spring Terminal

(V and W suffixes only)

20 J

OUTPUT SPECIFICATIONS

(2)

Description 30A

Operating Voltage (47-440Hz) [VRMS] 48-600

Transient Overvoltage [Vpk]

(3) 1200

Maximum Off-State Leakage Current @ Rated Voltage [mA

RMS] 1

Minimum Off-State dV/dt @ Maximum Rated Voltage [V/μsec] 500

Load Current, General Use UL508/LC A IEC62314 @ 40°C [A

RMS] 30

Minimum Load Current [mA

RMS] 100

Maximum 1 Cycle Surge Current (50/60Hz) [Apk] 716/750

Maximum On-State Voltage Drop @ Rated Current [Vpk] 1.35

Maximum 1/2 Cycle I² t for Fusing (50/60Hz) [A² sec] 2563/2343

35A20A

48-600 48-600

1200 1200

1 1

500 500

20 35

Load Current, Motor Starting UL508 FLA/LC B IEC62314 @ 40°C [ARMS] 14/7.6

8.5/4.8 26/14

100 150

286/300 1290/1350

1.35 1.3

409/375 8320/7593

Minimum Power Factor (at Maximum Load)

(4) 0.5

0.5 0.5

Motor Rating UL 508/IEC62314 [HP (kW)]: 120 VAC 1 (0.74)

0.5 (0.37) 2 (1.5)

Motor Rating UL 508/IEC62314 [HP (kW)]: 240 VAC 3 (2.2)

1.5 (1.1) 5 (3.73)

Motor Rating UL 508/IEC62314 [HP (kW)]: 480 VAC 5 (3.7)

3 (2.24) 10 (7.4)

INPUT SPECIFICATIONS

(2)

Description DR2260Axxx

Control Voltage Range 90-280 VAC/VDC

Maximum Reverse Voltage -

Minimum Turn-On Voltage 90 VAC/VDC

Must Turn-Off Voltage 5 VAC/VDC

Minimum Input Current (for on-state) 6 mA

Maximum Input Current 10 mA

Nominal Input Impedance Current Limited

Maximum Turn-On Time [msec] 20

Maximum Turn-Off Time [msec] 30

DR2260Dxxx

4-32 VDC

-32 VDC

4 VDC

1 VDC

10 mA

15 mA

Current Limited

1/2 Cycle

(5) (6)

(7)

Datasheet

DIN Rail Mount

Do not forget to visit us at: www.crydom.com

Summary of content (8 pages)

PAGE 1
DIN Rail Mount Datasheet DR22 Series AC Output DIN Rail Mount SSRs • Output ratings up to 35 Amps at 600 VAC • Built-in overvoltage protection • Relay or Contactor configuration • Integral heat sink eliminates the need for complex thermal calculations • DBC substrate for superior thermal performance • "Elevator" screw option to allow the use of ring or lug type terminals • IP20 touch-safe housing • AC or DC control • C-UL-US and TUV approved PRODUCT SELECTION Control Voltage 90-280 VAC/VDC 4-32 VDC 20A
PAGE 2
DIN Rail Mount Datasheet GENERAL SPECIFICATIONS (2) Description Parameters Dielectric Strength, Input to Output (50/60Hz) Dielectric Strength, Input/Output to Case (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range (8) Ambient Storage Temperature Range Short Circuit Current Rating (9) Weight (typical) Housing Material Heat Sink Material Din Rail Clip Material Hardware Finish Input Terminal Screw Torque Range (in-lb/Nm) Load Terminal Sc
PAGE 3
DIN Rail Mount Datasheet THERMAL DERATE INFORMATION (8) DR2260x20x Single unit (12) DR2260x30x Single unit (12) Multiple units 15 10 5 0 20 30 40 50 60 Ambient Temperature (ºC) 70 30 35 25 30 20 15 10 5 0 80 Single unit (12) Load Current (Amps) Load Current (Amps) Load Current (Amps) 20 DR2260x35x Multiple units 20 30 40 50 60 Ambient Temperature (ºC) 70 EQUIVALENT CIRCUIT BLOCK DIAGRAMS/WIRING DIAGRAM DC Control +3/A1 OUTPUT DC V - 1/L1 INPUT + Trigger Circuit 2/T1 -4
PAGE 4
DIN Rail Mount Datasheet MECHANICAL SPECIFICATIONS Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] Contactor Configuration 1.87 [47.5] Input Connector 1/L1 2.85 [72.3] +3/A1 1.88 [47.8] -4/A2 3.62 [91.9] 3.54 [90] Screw Terminal Spring Terminal 2/T1 1.19 [30.2] 0.89 [22.5] 4.59 [116.5] Protective Earth Connection Relay Configuration 0.39 [9.9] +3/A1 INPUT -4/A2 3.00 [76.2] 3.67 [93.2] 1.88 [47.8] 1/L1 OUTPUT 3.
PAGE 5
DIN Rail Mount Datasheet ACCESSORIES Recommended Accessories New Accessories! Connectors Part number: CP201, CP202 Connectors ID Marker Lug Terminal CP201 CNLB TRM0 CP202 CNLN TRM6 Pluggable input connectors, 2 position, with screw terminals (CP201) or spring type terminals (CP202). Compatible with Contactor Configuration NOVA22 SSRs. Lug Terminal CNL2 Part number: TRM0 Copper wire lug for AWG 6 (13.3 mm²) to AWG 0 (53.5 mm²) wire size.
PAGE 6
DIN Rail Mount Datasheet GENERAL NOTES (1) Control voltage 18-52 VAC/VDC is available upon request. (2) All parameters at 25°C unless otherwise specified. (3) Output will self trigger between 900-1200 Vpk, not suitable for capacitive loads. (4) High inductive loads requires nominal control voltage; AC input models only. (5) Increase minimum voltage by 1 V for operations from -20 to -40°C. (6) For ambient temperatures above 40°C the maximum control voltage must not exceed 250 VAC/VDC.
PAGE 7
DIN Rail Mount Datasheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo.
PAGE 8
DIN Rail Mount Datasheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.