Datasheet

ManualsBrandsCRYDOM ManualsContactorsDRH3P60A18

DRH Series

• Ratings up to 18 & 20 Amps at 600VAC

• Fits standard 35mm DIN Rail

• Integrated over-temperature protection

• Alarm output in case of over-temperature

• Multicolor LED with input status and alarm indicator

• AC or DC control

• Zero Voltage (resistive loads) or instantaneous (inductive loads) turn-on output

• C-UL-US Listed,

IEC Rated, CE & RoHS Compliant, Horsepower Rated

• Built-in Overvoltage Protection

• Fan controlled through thermistor and microprocessor to optimize fan operation

PRODUCT SELECTION

Control Voltage 18A

90-280 VAC/VDC DRH3P60A18

4-32 VDC DRH3P60D18

20A

DRH3P60A20

DRH3P60D20

AVAILABLE OPTIONS

Required for valid part number

For options only and not required for valid part number

Function

3P: Contactor

Switching Type

Blank: Zero Voltage Turn-On

R: Instantaneous Turn-On

Operating Voltage

60: 48-600 VAC

Series

DRH 3P 60 R

Control Voltage

A: 90-280 VAC/VDC

D: 4-32 VDC

Rated Load Current

18: 18 Amps (3 Controlled legs)

20: 20 Amps (2 Controlled legs)

OUTPUT SPECIFICATIONS

(1)

Description

Operating Voltage (47-63Hz) [VRMS]

Transient Overvoltage [Vpk]

(2)

Maximum Off-State Leakage Current @ Rated Voltage [mARMS]

Minimum Off-State dV/dt @ Maximum Rated Voltage [V/μsec]

Load Current, General Use UL508/IEC62314 @ 40°C [A

RMS] (3)

Minimum Load Current [A

RMS]

Maximum Surge Current [Apk] 1Cycle 60Hz

Maximum Surge Current [Apk] 1Cycle 50Hz

Maximum I²t for Fusing (8.33 msec) [A²sec]

20A18A

48-600 48-600

1200 1200

3 3

500 500

18 20

Load Current, Motor Starting UL508 FLA/IEC62314 @ 40°C [ARMS] (3)

7.6 7.6

0.15 0.15

750 750

716 716

2330 2330

Maximum I²t for Fusing (10 msec) [A²sec]

2560 2560

Maximum On-State Voltage Drop @ Rated Current [Vpk]

1.35 per channel 1.35 per channel

Minimum Power Factor (with Maximum Load)

0.5 0.5

Motor Rating UL 508/ IEC60947-4-2 [HP/kW] :240 VAC

2/1.5 2/1.5

Motor Rating UL 508/ IEC60947-4-2 [HP/kW] :380 VAC

3/2.2 3/2.2

Motor Rating UL 508/ IEC60947-4-2 [HP/kW] :480 VAC

5/3.7 5/3.7

INPUT SPECIFICATIONS

(1)

Description DRH3P60Ax

Control Voltage Range 90-280 VAC/VDC

Minimum Turn-On Voltage 90 VAC/VDC

Must Turn-Off Voltage 10 VAC

Minimum Input Current (for on-state) 1 mA

Maximum Input Current 3 mA

Nominal Input Impedance [Ohms] 100k

Maximum Turn-On Time [msec] 30

Maximum Turn-Off Time [msec] 40

DRH3P60Dx

4-32 VDC

4 VDC

1 VDC

2 mA

17 mA

1 Cycle

(4)

Do not forget to visit us at: www.crydom.com

Datasheet

DIN Rail Mount

Summary of content (8 pages)

PAGE 1
DIN Rail Mount Datasheet DRH Series • Ratings up to 18 & 20 Amps at 600VAC • Fits standard 35mm DIN Rail • Integrated over-temperature protection • Alarm output in case of over-temperature • Multicolor LED with input status and alarm indicator • AC or DC control • Zero Voltage (resistive loads) or instantaneous (inductive loads) turn-on output • C-UL-US Listed, IEC Rated, CE & RoHS Compliant, Horsepower Rated • Built-in Overvoltage Protection • Fan controlled through thermistor and microprocessor to optimi
PAGE 2
DIN Rail Mount Datasheet POWER SUPPLY SPECIFICATIONS (1) Description DRH3P60Dx Voltage Range Minimum Turn-On Voltage Must Turn-Off Voltage Maximum Source Current [mA] Maximun Start Up Time [msec] Maximun Shut Off Time [msec] ALARM OUTPUT DRH3P60Ax 90-265 VAC/VDC 90 VAC/VDC 5 VAC/VDC 40 50 500 8-32 VDC 8 VDC 3 VDC 125 20 40 (1) Description DRH3P60xxx Maximum Contact Switching Voltage [Volts] Contact Rated Current [A] Minimum Recommended Contact Load [mA] Static Contact Resistance (max. init.
PAGE 3
DIN Rail Mount Datasheet WIRING AND BLOCK DIAGRAM L1 L2 L3 48-600 VAC, 50-60Hz L1 L2 L3 T2 /> L2 L3 +A3 13 +A1 DRH3P60xxx IND. CONT. EQ. -A4 T1 CONTROL INPUT INPUT STATUS XXXX Motor Controller / AC-53a Application T1 /> L1 Alarm Output (0.
PAGE 4
DIN Rail Mount Datasheet SHORT CIRCUIT AND OVERLOAD PROTECTION FOR ALL DEVICES IEC standard 60947-4-1 make a distinction between two different types of protection, (called “coordination”), which are designated types “1” and "2". Any short-circuit that occurs is cleared safely by either type of coordination. The only difference between the 2 categories concerns the extent of the SSR damage caused by the short-circuit.
PAGE 5
DIN Rail Mount Datasheet STATUS CHART 1 2 3 4 5 6 50% 75% 100% 7 8 9 10 11 100% 75% 12 13 14 15 Control Input A1 Power Supply A3 Output Over Temperature Alarm Pre-alarm Alarm Output LED Color 2s 3s 0% 50% 3s 3s Fan Speed Step LED Color Description Blue 1, 15 Initial Condition 2, 14 Stand by condition. LED is blinking Blue. Fan is activated at full speed for 2 seconds after power is applied to A3 3 Green A1 is On, Output is activated, temperature rises.
PAGE 6
DIN Rail Mount Datasheet ACCESSORIES ID Marker ID Marker CNLB CNLN Package of 10 plastic strip comprising 10 individual markers which can be placed for easy identification during the use of multiple units. CNL2 AGENCY APPROVALS Certification in accordance with: United States Standard for Industrial Control Equipment - UL 508 and Canadian Standard Association for Industrial Control Equipment – C22.2 No. 14.
PAGE 7
DIN Rail Mount Datasheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo.
PAGE 8
DIN Rail Mount Datasheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.