4 Channel Video Range 500m 5GHz Frequency Ultra Low Latency IP CVW Beamlink-Quad Streaming 4TX-to-1RX Wireless HD Video Transmission System Full HD RX RX High Definition Double RX User Manual EU Environmental Protection This uesr manual applies to: Waste electrical products should not be disposed of with household waste. Transmitter:7060 Receiver:3060 Please recycle where facilities exist. Check with you local authority or retailer User Manual V1.0 for recycling advice. 2018.11.
Thank you for choosing CVW's professional wireless HD audio and video transmission product. Read the following precautions carefully before using this product: 目录 About the User Manual 01 * Do not use this product for a long time in the sun or dusty place. Product Features 01 * Be sure to use this product within the temperature and humidity ranges. Brief introduction 01 * Do not operate the product under vibration or strong magnetic fields.
About the User Manual This Manual details the product specifications, instructions for use, precautions, and troubleshooting. Read the Manual carefully before using the product. If you have any questions or difficulties in using this product, contact the company or the seller in time. Product Features BeamLink Quad is a set of 4TX-to-1RX full-HD audio and video wireless transmission system.
Structure & Interface Transmitter Key Operation Function TX: 7060 Operation SONY NPF Battery dock Antenna Interface OLED Display LNA ON/OFF High-gain and low-gain mode switching Press the “LNA ON/OFF” button for about 3s WPS/RTSP Reset Network status warning light Description “L” (low-gain) mode: Applicable for close-range(<200m/656ft & LOS) and strong interference environments, with strong anti-interference ability.
RX: 3060 Receiver Key Operation Function Antenna Interface Frequency channel switching Operation Description Short press the “CH/WPS” button about 1S After the receiver switches the frequency channel about 1S , the OLED display of the receiver and transmitter will display the new frequency channel about 1S number after switching.
Product Installation For transmitter 1. Please install all the antennas on the transmitter and make them in a fan shape as shown in the picture. Distance>1m Distance>1m Distance>1m Transmitter at a height of around 1.5 to 2 meters above floor. 3. Please connect the transmitter and camera with SDI or HDMI cable. 2. Please fix the transmitter via the screw at the bottom or the V-mount at the back, that the distance between each transmitter is more than 1 meter.
B: Vertical placement Receiver Installation A: Horizontal placement 1. Please install all the antennas on the receiver, and make them in a fan shape as shown in the picture. Place the receiver at a height of around 1.5 to 2 meters above floor. install the affiliated metal stand 3. Please connect the receiver and video switch console or monitor with SDI or/and HDMI cable.
4. The receiver can be powered by both the V-mount battery and DC-IN port via Product Application the affiliated power adapter. If the mentioned two types of power supply are connected at the same time, the lithium battery is prioritized in power supplying, and the battery will switch to the power adapter for power supplying automatically after the battery power is exhausted.
OLED Display Description Streaming mode In streaming mode, the four channel video sources are transmitted to the four transmitters via HDMI or SDI respectively. The receiver will receive the four RTSP streamings from the four transmitters and send them to the switch console through the LAN port. You can also connect the receiver with mobile devices such as your mobile phone, tablet and PC via WiFi, and watch the live video on the mobile phone, tablet and PC .
Functional Instructions RX:3060 Tally function Insert the Tally light into the transmitter’s Tally output interface first, CH2 WPS L 1 the transmitter’s Tally light is on. 4 Icon Transmitter ID Frequency Channel Signal Icon Video Gain State WPS 15 Tally interface of the transmitter and receiver: The transmitter’s Tally VIDEO Signal Icon interface is a DB9 female. VIDEO Tally light output interface: Video VIDEO CH* X Signal bar J16 Status Content Numbers 1~4 interface is a standard φ3.
Streaming Function DB9_FEMALE J15 5 9 4 8 3 7 2 6 1 GP8 GP7 GP6 GP5 GP4 GP3 GP2 GP1 When using the functions in streaming mode, the transmitter needs to switch to streaming mode. At this time, the word “RTSP” is displayed on the transmitter’s OLED display, the SDI and HDMI at the receiver have no video output, and the image is transmitted to the streaming media software through the LAN port of the receiver for decoding display. The streaming mode depends on software decoding.
Open internet browser, and enter transmitter’s encoder or receiver’s decoder IP address in the address bar to enter the parameter settings page. All transmitter’s encoder and receiver’s decoders need to be configured one by one, please refer to the following configuration case. Transmitter Encoder Case (transmitter 2): IP ETHADDR Transmitter IP address(192.168.1.111~114). Do not change the IP, otherwise the wireless connection will be shut down. 192.168.1.
Wireless Transmission Module Upgrading Each transmitter has one wireless transmission module, and the software upgrading needs to be implemented on each transmitter. Receiver also has one wireless transmission module, and the software upgrading needs to be implemented on it accordingly. First, connect the computer to the LAN port of the receiver; Then enter the device’s WiFi IP (wireless transmission module IP) in the address bar to enter the login page: 1.
Product Specifications Select the “Upgrade” option in the “System” column. ITEM TX:7060 RX:3060 5190MHZ, 5230MHZ , 5755MHZ , 5795MHZ Frequency Optional：5270MHZ , 5310MHZ , 5510MHZ , 5550MHZ , 5590MHZ, 5630MHZ, 5670MHZ Antenna 4*4 MIMO 5dBi External antenna Modulation mode OFDM Transmission Power 17dBm EVM ≤- 28dB Receiving Sensitivity ≤- 70dBm Bandwidth 40MHz Wireless 802.
Trouble Shooting Trouble Precautions Solutions Lift the transmitter and receiver as high as possible, to 1.
3. When using the device, be sure to install the antenna before turning on the power. Failure to do so may result in damage to the device. 4. When used, the surrounding environment will affect the quality of wireless transmission. Poor operating environment may cause image sound disorder, such as picture pause, noise, etc. Therefore, pay attention to the following: Walls, large metal plates, and appliances can affect wireless transmission. Try to avoid using in these environments.
