2 Channel Video Range 700m 5GHz Frequency Ultra Low Latency IP CVW Beamlink-Duo Streaming 2TX-to-1RX Wireless HD Video Transmission System Full HD RX RX High Definition Double RX User Manual EU Environmental Protection This user manual applies to: Waste electrical products should not be disposed of with household waste. Transmitter:7060 Receiver:3062 Please recycle where facilities exist. Check with you local authority or retailer User Manual V1.0 for recycling advice. 2019.01.
Thank you for choosing CVW's professional wireless HD audio and video transmission product. Read the following precautions carefully before using this product: Contents About the User Manual 01 Product Features 01 * Do not use this product for a long time in the sun or dusty place. * Be sure to use this product within the temperature and humidity ranges. * Do not operate the product under vibration or strong magnetic fields.
About the User Manual This Manual details the product specifications, instructions for use, precautions, and troubleshooting. Read the Manual carefully before using the product. If you have any questions or difficulties in using this product, contact the company or the seller in time. Product Features BeamLink Duo is a set of 2TX-to-1RX full-HD audio and video wireless transmission system.
Structure & Interface Transmitter Key Operation Function TX: 7060 SONY NPF Battery dock Antenna Interface Hold the “LNA on/off” button for 3 seconds to switch the mode. OLED Display LNA ON/OFF Operation High-gain and low-gain mode switching WPS/RTSP OLED with “L” letter means low-gain mode. OLED without “L” letter means high-gain mode. Reset Network status warning light Description Line-of-sight scenarios: TX-to-RX <200m/656ft: L(low-gain) mode is recommended.
RX: 3062 Receiver Key Operation Function Antenna Interface Frequency channel switching Operation Description Short press the “CH/WPS” button about 1S After the receiver switches the frequency channel about 1S , the OLED display of the receiver and transmitter will display the new frequency channel about 1S number after switching. RS232/422 Tally in Hold the “LNA on/off” button for 3 seconds to switch the mode.
Product Installation For transmitter 1. Please install all the antennas on the transmitter and make them in a fan shape as shown in the picture. Distance>1m Transmitter at a height of around 1.5 to 2 meters above floor. 3. Please connect the transmitter and camera with SDI or HDMI cable. 2. Please fix the transmitter via the screw at the bottom or the V-mount at the back, that the distance between each transmitter is more than 1 meter. 07 HDMI Input HDMI and place it at a height of around 1.
B: Vertical placement Receiver Installation A: Horizontal placement 1. Please install all the antennas on the receiver, and make them in a fan shape as shown in the picture. Place the receiver at a height of around 1.5 to 2 meters above floor. install the affiliated metal stand 3. Please connect the receiver and video switch console or monitor with SDI or HDMI cable. 00:00:00 HDMI 09 SDI Out SDI Out SDI metal stand before placing the receiver in vertical position.
4. The receiver can be powered by both the V-mount battery and DC-IN port via Product Application the affiliated power adapter. If the mentioned two types of power supply are connected at the same time, the lithium battery is prioritized in power supplying, and the battery will switch to the power adapter for power supplying automatically after the battery power is exhausted. Point-to-Point mode In point-to-point mode, the 2 channel video sources are sent to the 2 channel transmitters via HDMI or SDI.
OLED Display Description Streaming mode In streaming mode, the 2 channel video sources are sent to the 2 channel transmitters via HDMI or SDI. The receiver will receive the RTSP protocol network signals from the 2 channel transmitters and send them to the embedded switch console for display through the network port. You can connect to the WiFi at the receiver via your mobile phone or tablet, and watch it through the player on the mobile phone or tablet.
Functional Instructions RX:3062 Tally function Insert the Tally light into the transmitter’s Tally output interface first, Frequency point then connect the switch console to the receiver’s Tally input interface, and then control the Tally light of the two transmitters through the switch CH2 WPS L console. When the receiver is triggered by a low-level current, the transmitter’s Tally light is on.
Streaming Function Tally light input interface: R595 Tally1 When using the functions in streaming mode, the transmitter needs to switch to streaming mode. At this time, the word “RTSP” is displayed on the transmitter’s OLED display, the SDI and HDMI at the receiver have no video output, and the image is transmitted to the streaming media software through the LAN port of the receiver for decoding display. The streaming mode depends on software decoding. Comply with lots of streaming media software.
Open internet browser, and enter transmitter’s encoder or receiver’s decoder IP address in the address bar to enter the parameter settings page. All transmitter’s encoder and receiver’s decoders need to be configured one by one, please refer to the following configuration case. Transmitter Encoder Case (transmitter 2): IP ETHADDR Transmitter IP address(192.168.1.111~112). Do not change the IP, otherwise the wireless connection will be shut down. 192.168.1.
Wireless Transmission Module Upgrading Each transmitter has one wireless transmission module, and the software upgrading needs to be implemented on each transmitter. Receiver also has one wireless transmission module, and the software upgrading needs to be implemented on it accordingly. First, connect the computer to the LAN port of the receiver; Then enter the device’s WiFi IP (wireless transmission module IP) in the address bar to enter the login page: 1.
Product Specifications Select the “Upgrade” option in the “System” column. ITEM TX:7060 RX:3062 5190MHZ, 5230MHZ , 5755MHZ , 5795MHZ Frequency Optional:5270MHZ , 5310MHZ , 5510MHZ , 5550MHZ , 5590MHZ, 5630MHZ, 5670MHZ Antenna 4*4 MIMO 5dBi External antenna Modulation mode OFDM Transmission Power 17dBm EVM ≤- 28dB Receiving Sensitivity ≤- 70dBm Bandwidth 40MHz Wireless 802.
Trouble Shooting Trouble Precautions Solutions Lift the transmitter and receiver as high as possible, to 1.
3. When using the device, be sure to install the antenna before turning on the power. Failure to do so may result in damage to the device. 4. When used, the surrounding environment will affect the quality of wireless transmission. Poor operating environment may cause image sound disorder, such as picture pause, noise, etc. Therefore, pay attention to the following: Walls, large metal plates, and appliances can affect wireless transmission. Try to avoid using in these environments.