User guide

VPS-2300 User Guide
2 Familiarizing with Crystalio
2.3 – Remote Control
A remote control is supplied with your Crystalio for
your direct access to the commonly used functions.
Note: Insert batteries to remote control before using.
1 Power ON & OFF buttons
Press ON to switch your Crystalio
on and press OFF to switch to
standby mode.
!!Caution: When Crystalio is
switched off, please wait for at
least 10 seconds before switching
it on again.
2 Video Settings buttons
Use these buttons to configure
the appearance of the video being
displayed. Parameters available
for customization including
BRIGHTness, CONTRAST,
COLOR saturation, RGB
OFFSET, RGB GAIN, and HUE.
Refer to Section 5.4 for details.
3 Aspect Ratio buttons
To switch to the common aspect
ratio settings directly including
4:3, 16:9, 2.35:1, and SCREEN.
Refer to Section 5.3 for details.
4 Input Select buttons
To select the active video source
directly including SDI 1, Video,
Component, and DVI etc. Refer to
Section 5.2 for details.
5 Navigation buttons
6 ENTER button
ENTER button acts the same as
the SETUP / OK button on the
front panel. It is used to enter the
menu setup mode and to select
item or confirm setting.
7 ESC button
ESCape button acts the same as the CANCEL
button on the front panel. It is used to exit and go
back one level of the menu setup
8 LCD ON / LCD ACTIVE / LCD OFF buttons
To control the backlight of LCD display on the
front panel. Refer to Section 5.5 for details.
9 AR STORE PROFILE button
Use this to memorize Aspect Ratio profiles.
10 AR PROFILE buttons
To recall stored Aspect Ratio profiles. Refer to
Section 5.7 for details.
11 USER STORE PROFILE button
To store user-defined video
profiles.
12 VIDEO USER PROFILE buttons
To recall stored user profiles. Refer
to Section 5.8 for details.
13 POSITION CUSTOM CENTRE
Use this together with the
Navigation buttons to control the
position of displayed image. Refer
to Section 5.5 for details.
14 LED ACTIVE / LED OFF buttons
To switch on and off the LED
indicators on the front panel.
15 PIXEL MAGIC 1:1 button
To activate Pixel Magic System.
Refer to Section 5.9 for details.
16 ZOOM buttons
To scale displayed image so that it
makes the image perfectly fit the
display device. These include
ZOOM, BEST FIT, ZOOM IN,
ZOOM OUT, FULL WIDTH, &
FULL HEIGHT. Refer to Section
5.5 for details.
17 Deinterlace buttons
Use these to select deinterlace
method including AUTO, VIDEO,
NTSC@30 ON, 2:2 EVEN, and 2:2
ODD. Refer to Section 5.5 for
details.
18 NLS button
Use this to switch on and off Non-Linear
Stretching. Refer to Section 5.5 for details.
16:9 GAINOFFSET HUE
2.35:1 SDI 2SDI 1 SDI 3
SCREEN
COMPONENT1
VIDEO
COMPONENT2
HDTV SVIDEO 1DVI SVIDEO 2
ENTER
L
CD
ACT
IVE
LCD
ON
E
SC
LC
D
OF
F
STORE PROFILE
AR USER CUSTOM CENTER
POSITION
LED ACTIVE PIXEL MAGIC 1:1 LED OFF
FULL WIDTH FULL HEIGHT
ZOOM
Z OOM IN
ZO OM OUT
BEST FIT
AR PROF ILE
12
43
56
VIDEO USER PROFILE
2:2 EVEN NTSC30 ON VIDEO AUTO
2:2 ODD NLS
1 2 43
OFF ON
4:3 BRIGHT CONTRAST COLOR
1
2
3
4
8
6
5
7
9
11
13
14
15
18
16
10
12
17