User`s guide

214 Guardall Director V4.74 User's Guide 21-0381E v4.7.4
Card/PIN: "Card or PIN" means "Card-Only, or User-
ID+PIN". With "Card+PIN", the card must be
presented (does not allow UID+PIN).
Manual Disarming
: For an armed area that is NOT set
to 'Auto Disarm on Valid Token', the user will also
have to access the alarm system and disarm the area.
For details on the "Auto-Disarm" feature, refer to
"Areas and Related Settings".
Reader Mode
- Schedule, and In / Out of schedule: These
settings specify whether one user can enter,
or if a second valid user (or designated
'escort') will be required to enter their
Card/PIN as well. If scheduled, different entry
requirements can be selected for when the
schedule is active versus outside of the
chosen schedule.
Toggle Lock/Unlock (all vs. authorized) V4.4:
Causes the door to toggle from locked to unlocked (or
vice-versa) when a card is accepted at this reader.
"All" means it will work for any valid card. "Authorized"
means this will work only for users with 'Door Control'
authority.
With "Dual Custody
", two different users must present
their card and/or PIN (and neither of them can be set
as "Visitor--Escort Required").
When set to "Escort
", a valid 'escort' can also enter on
their own by presenting their card/PIN twice. If visitor
cards (set to require an escort) are presented, visitor
escort processing will take over (e.g., with visitor
processing, you can set the type of cards escorts can
use). Users are defined as escorts (escort privilege)
through their authority assignments.
Related Topics
:
 Authorities, Profile 1-4, Access, Escort
Privilege, and
Visitor (Escort Required). See: Authorities for
Users / Entrants.
 Type of Cards that can Escort Visitors
: Under
"Account-Wide Panel Settings", look for "Setup",
then "Escort-Required Mode".
 Dual custody is also supported pertaining to the
disarming of an area. For details, refer to "Areas
and Related Settings".
Lockout
- Schedule / Mode: These settings specify
whether all users are to be denied entry either
while a selected schedule is active, or outside
of the chosen schedule. Tip: To disable this
feature, select "None" for the schedule.
Users with 'Master Override' authority can enter while
a 'lockout' is in effect. For details refer to the "Master
Override" setting under "Authorities for
Users/Entrants".
Miscellaneous
- Arming Station: Select this to identify an
"arming station".
An arming station includes a Wiegand reader with
keypad, and supports additional functions for arming
and disarming areas, adjusting the area closing time
(worklate), etc. For details, refer to the User's Guide
for your xL system (panel/LCD keypad).
Note: Arming-station wiring differs from other readers
(ensure the proper installation instructions have been
followed).
- Enable Class Checking:
Selected (): This selection is required if user-
access to this reader is to be controlled based on time
of day and/or door class. See [Class Map] to
follow/below. Not Selected
: Provides 24-hr
access/egress to all valid cards regardless of the
users' assigned schedule and door class authorities.
[Class Map]
- Schedule, In / Out of schedule, and Class
A/B/C: These settings allow restricting
access to only the users with specific door-
class authority, and/or optionally blocking
after-hours access to this specific reader
(except users with 'Master Override'
authority). If scheduled, a different set of
door-class requirements can be selected for
when the schedule is active versus outside of
the chosen schedule.
To block after-hours access to this reader, select "Out
of Schedule" None. To remove class restrictions at
this reader (without bypassing each user's assigned
schedule), select A, B, C for both "In Schedule"
and "Out of Schedule".
Related Settings
:
 User's door-class authorities and scheduling are set
under: Authorities, Profile 1-4, Door
Class. See: Authorities for Users / Entrants.
- Group Number: Similar to 'Door Class'.
Each reader can be assigned a value here.
Users can enter only if their assigned
authority supports this group number.
-------------------------
- Log APB Violation Only: This will cause
APB violations to be recorded, while allowing
the person to enter.
- Detect Antipassback: This enables /
disables the Antipassback feature for this
reader.
Antipassback (APB): A feature that blocks individual
cards from being used to: