User`s guide

21-0381E v4.7.4
Welcome Report Control Admin
Sys Config Tech-Ref
215
+ Re-enter the same area, or;
+ Re-enter the facility from 'outside', and/or;
+ (Optional): Enter other areas;
…Unless
they are recorded as exiting first--i.e., each
person must use their card/token at every reader they
encounter (that is set to "Detect Antipassback"). Tip:
This helps to protect against unauthorized card usage.
Note
: Antipassback-controlled areas typically require
an exit reader on each door.
Antipassback operation can be customized on an
area-by-area basis. For details, refer to
"Antipassback" under "Areas and Related Settings".
The antipassback status can be reset for a specific
user, or for all users in a specific area (to allow their
next entry or exit regardless of their previous APB
status). For details, refer to "Resetting Users'
Antipassback Status", and/or "Resetting the
Antipassback Status for Users in a Specific Area" in
the Control & Status Chapter.
[Card Action]
- Card Action: This is an optional feature that
sets a reader to enable (enrol) or disable
(invalidate) a selected type of cards when
accepted by the reader. You can select whether
or not the door will also unlock, and other
parameters (to follow.)
Blue Text: With a card-enrolment reader (i.e., "Enable
Cards"), you can set whether expired and/or
"Enrolment Pending" cards will be affected (Also see:
'Related Settings', after "Option"--to follow / below).
The present selection for this will be shown in blue
text. Application Tip
: 'Expired' cards also includes
cards that had been previously enabled for a set
period of time.
Access vs. Card Action vs. Denied
: Valid cards that
are not affected by the 'Card Action' will simply be
granted access (i.e., the reader will operate like any
other reader). This includes cards that are already
valid (enrolment reader), and cards other than the
selected 'Card Type'. Cards that are NOT authorized
for this reader at this time (per user authorities), will be
denied access, and the card-action will NOT occur.
- Card Type: The type of cards to be affected by
an 'enable' or 'disable' card-action.
Never: Normal operation (same as selecting "No
Card Action");
Escort-Required Users
: Users with "Visitor (Escort
Required)" authority (although an escort will not be
needed for cards being enabled/disabled);
Tip: To enforce the 'escort' requirement for visitors at
an enrolment station, ensure "Unlock Door..." is NOT
selected. The visitor can 'badge' once to enable the
card initially, and then the visitor and escort can use
their cards to gain entry as usual.
Temporary Users
: All cards that are set with an
expiry date;
All Users
: All cards presented at this reader (with
authority for its area).
- Unlock Door on Card Action: Whether or not
the door will unlock (plus the associated 'access
granted' message).
Note: This setting applies only as part of a 'card
action' taking place (i.e., the door always unlocks for
cards simply being granted access).
- Duration: This determines how long the
enabled cards can be used (from the moment
they are activated).
End of Today (Schedule 50): This allows enabling
cards for the present day only--while schedule #50 is
active ("in window"). If schedule #50 has no times set
for the present weekday/date, the action will not occur.
Note: Schedule #50 must be set up:
Ref
: (My Account) Schedules
 Schedules for User Access and Area Automation
- Option: For 'disable' commands, "Duration"
changes to "Option":
Permanent: The cards will be disabled, and NOT set
as "Pending Enrolment" (they can be re-enabled only
if the account is set to "Ignore Pending Enrolment".
(See 'Related Settings', to follow / below.
Pending Enrolment
: The cards will be set to allow
future re-enrolment.
(Permanent or Pending Enrolment) : Auxiliary
Output: Each time a card is disabled, the auxiliary
relay will be triggered. This can be used for a turnstile
card-capture application. Note: The aux. relay must
be set to "Door Opener" mode. The relay duration is
set in the same screen.
Locator (to follow / below)
:
Aux In/Out, Auxiliary Output Relay.
Related Settings
:
 Account Information, Setup, Card Action
(Ignore Pending Enrolment).
See
: Account-Wide Panel Settings.
 Users, Validation, Pending Enrolment, and
Invalid On.
See
: Users (Entrants/Panel Users).
 Authorities, Profile 1-4, Access, Visitor
(Escort Required)
See
: Authorities for Users / Entrants.