FRM220 Hardware Installation
CTC Union Technologies Co., Ltd. Far Eastern Vienna Technology Center (Neihu Technology Park) 8F, No. 60 Zhouzi St. Neihu District Taipei 114 Taiwan Tel: +886-2-26591021 Fax: +886-2-27991355 Email: info@ctcu.com URL: http://www.ctcu.com FRM220 Hardware Installation Manual Fiber In-band Managed Media Platform Rack, 20 Slot, 2U Version 1.0 Dec. 2008 (Release) Version 1.1 July 8, 2009 (Update, added card introductions) Version 1.11 July 20, 2009 (Update, add management quick start) Version 1.
Legal The information in this publication has been carefully checked and is believed to be entirely accurate at the time of publication. CTC Union Technologies assumes no responsibility, however, for possible errors or omissions, or for any consequences resulting from the use of the information contained herein.
Table of Contents Chapter 1 Introduction.................................................................................................................................................................. 7 1.0 Introduction.......................................................................................................................................................................... 7 1.1 Functional Description ...........................................................................................
Table of Contents ii
Chapter 1 Introduction Chapter 1 Introduction 1.0 Introduction Thank you for choosing the FRM220 Platform Fiber Media Converter Rack. If you would like to skip right to the installation of the Converter Chassis, proceed to Chapters 2. This manual is used to explain the hardware installation procedures for the FRM220, and present its capabilities and specifications. This manual is divided into 2 Sections, the Introduction and Installation, plus the Appendix.
Chapter 1 Introduction 1.5 Chassis Specifications Environment Temperature Humidity -10 - 50°C Ambient (14-122°F) 5-95% non condensing Alarm relay contact ratings 125VAC 1A 110VDC 0.
Chapter 1 Introduction 1.7 Line card options The FRM220 is capable of supporting a variety of in-band managed or non-managed line card types which may be mixed and matched in any slot of the rack. See below for a brief of the linecards at the time of this printing. Please refer to the latest version of FRM220 NMC User Manual for details of all the line card options for the FRM220. 1.7.
Chapter 1 Introduction 1.7.2 FRM220-10/100iS-2 Dual Channel In-band managed 10/100 Fiber Media Converter The FRM-10/100iS-2 (in-band converter) is a Dual Channel (2 converters in 1 card) In-band Managed (OAM) Fiber Ethernet media converter (MC) that supports 10Base-T or 100Base-TX and converts to 100Base-FX (fiber). The UTP side supports auto-negotiation or forced settings for speed and duplex by setting as well as auto-MDIX.
Chapter 1 Introduction 1.7.3 FRM220-10/100i-2E In-band managed 10/100 Fiber Media Converter The FRM-10/100i-2E (in-band converter) is an In-band Managed (OAM) Fiber Ethernet media converter (MC) that supports 2 Ethernet channels of 10Base-T or 100Base-TX and converts to 100Base-FX (fiber). The UTP ports support auto-negotiation or forced settings for speed and duplex by setting as well as auto-MDIX.
Chapter 1 Introduction 1.7.4 FRM220-10/100A(S) 802.3ah In-band managed 10/100 Fiber Media Converter This IEEE802.3ah OAM compliant copper to fiber Fast Ethernet solution is designed to make conversion between 10/100Base-TX and 100Base-FX with SC or ST connector. With SNMP agent and GUI Web-based management in the FRM220, the Network administrator can monitor, configure and control the activity of each 802.3ah series line card. This 802.
Chapter 1 Introduction 1.7.5 FRM220-1000EA(S) 802.3ah In-band managed Gigabit Fiber Media Converter This IEEE802.3ah OAM compliant copper to fiber Gigabit Ethernet solution is designed to make conversion between 10/100/1000Base-TX and 1000Base-SX/LX with SFP-LC connector. With SNMP agent and GUI Webbased management in the FRM220, the Network administrator can monitor, configure and control the activity of each 802.3ah series line card. This 802.
Chapter 1 Introduction 1.7.6 FRM220-1000EDS Managed Gigabit Fiber Media Converter The FRM220-1000EDS is a 4-port switch or dual channel (two in one) copper to fiber Gigabit Ethernet solution designed to make conversion between 10/100/1000Base-TX and 1000Base-SX/LX with SFP transceivers. With SNMP and Web-based management in the FRM220, the Network administrator can monitor, configure and control the activity of each card in the chassis.
Chapter 1 Introduction 1.7.7 FRM220-E1/T1 In-band managed G.703 E1/T1(DS1) Fiber Modem The FRM220-E1/T1 is a fiber modem transport for G.703 E1 or T1(DS1) transmission. The BNC model (E1 only) provides unbalanced 75 Ohm coaxial connections while the RJ-45 model provides balanced 100/120 Ohm connections over twisted pair wiring.
Chapter 1 Introduction 1.7.8 FRM220-Data In-band managed V.35, X.21, RS-530/449/232 Fiber Modem The FRM220-DATA is a fiber modem for high-speed (up to 8.192Mbps) synchronous or low speed synchronous and asynchronous data transmissions (V.35, RS-232, RS-530, X.21 or RS-449) over fiber optical media. When the FRM220-DATA card is placed in the FRM220 rack with SNMP management, in-band management allows viewing the card and remote modem's status, type, version, fiber link status, data link status and alarms.
Chapter 1 Introduction 1.7.9 FRM220-Serial/485 In-band managed RS-485/422/232 Fiber Modem The FRM220-Serial/485 provides an Asynchronous Fiber Modem solution to extend RS-485 or RS-232 transmission distance up to 2km over multimode fiber or up to 120km over single mode fiber. The modem is equipped with multiple interface circuits for connection to RS-232 or RS-485/422 (2 or 4 wire, full or half duplex).
Chapter 1 Introduction 1.7.10 FRM220-FXO/FXS In-band managed POTS (Voice) over Fiber Modem FRM220-FXO/FXS POTS phone line converter extender is used to connect PSTN voice signals to distant Plain Old Telephone (POTS) devices. FRM220-FXO/FXS provides a fiber media transport for POTS transmission and features an RJ-11C for copper connection. A pair of FRM220-FXO/FXS is required to implement an end to end system.
Chapter 1 Introduction 1.7.11 FRM220-155MS SM/MM, MM/SM converter / repeater The FRM220-155MS is a fiber to fiber optical media converter and repeater that allows data rates up to 155Mbps. FRM220-155MS supports 2R regeneration, which consists of re-amplification and reshaping. This converter is compatible with fiber interfaces such as 100Mbps Fast Ethernet, 155Mbps STM1 and OC3.
Chapter 1 Introduction 1.7.12 FRM220-2.7G-2S, 2.7Gbps 3R Fiber Transponder The FRM220-2.7G-2S is an optical 3R regeneration device, which provides re-amplification, reshaping and retiming. The transponder card converts a data signal to the correct wavelength for transmission on a specific channel by supporting SFP optics on both line side and client side interfaces. When the FRM220-2.
Chapter 1 Introduction 1.7.13 FRM220-2.7G-3S 3R Transponder with Protection The FRM220-2.7G-3S is an optical 3R regeneration device, which provides re-amplification, reshaping and retiming and offers fiber protection. The transponder card converts a data signal to the correct wavelength for transmission on a specific channel by supporting SFP optics on line side to Primary or Secondary interfaces. When the FRM220-2.
Chapter 1 Introduction 1.7.14 FRM220-10G-xx 10Gbps 3R Fiber Transponder The FRM220-10G-xx is a series of managed 10G fiber to fiber 3R repeater/transponders. Based on a number of 10 Gigabit Fiber standards, these transponders support XFP to XFP (XX), SFP+ to XFP (SX), or SFP+ to SFP+ (SS) fiber connections. The transponders are protocol transparent, providing 3R regeneration between these different optical module types.
Chapter 1 Introduction 1.7.15 FRM220-MD40/80 CWDM Mux/DeMux The FRM220-MD40 is 4 channels MUX / DEMUX, modular design card for CWDM wavelengths including 1510nm, 1530nm, 1550nm, 1570nm. The FRM220-MD40-UP02 is 4 channels MUX / DEMUX, modular design card for CWDM wavelengths including 1470nm, 1490nm, 1590nm, 1610nm and two upgrade ports for CWDM wavelength ranges of 1503nm ~ 1577nm and 1260nm ~ 1457nm.
Chapter 1 Introduction 1.7.16 FRM220-iMUX Inverse Multiplexer Blades The FRM220A-nE1/ET100 are 5, 8 or 16 E1 port inverse multiplexer cards with built-in Bridge for the FRM220/220A Series Platform Media Converter Rack. The multiplexers support bundling Unframed E1s using GFP-F (Generic Framing Procedure-Framed). The clock source may be selected internally or recovered from any one of the received E1 signals. The Ethernet port utilizes a single RJ-45 connector or SFP for optical fiber, depending on model.
Chapter 1 Introduction 1.7.17 FRM220-Eoe1 Ethernet over E1 Converter The FRM220A-Eoe1 is a single port G.703/704 Fractional E1 DSU/CSU card with built-in HDLC Bridge for the FRM220/220A Series Platform Media Converter Rack. The converter supports Unframed, PCM31, and PCM30 framing modes. The clock source may be selected internally or recovered from received E1 signal. The Ethernet port utilizes a single RJ-45 connector.
Chapter 1 Introduction 1.7.18 FRM220-E1/Data DSU/CSU Converter Card The FRM220-E1/Data is a single port G.703/704 Fractional E1 DSU/CSU card for the FRM220/220A Series Platform Media Converter Rack. The converter supports Unframed, PCM31, PCM31+CRC4, PCM30, and PCM30+CRC4 framing modes. The clock source may be selected internally, recovered from received E1 signal, externally from the Data port or transparent. The Data port interface utilizes a single Hi-Density 26pin connector.
Chapter 1 Introduction 1.7.19 FRM220-FTEC E1/T1 Cross Rate Converter Card The FRM220-FTEC is a T1 (US Standard) /E1 (European Standard) converter and timeslot cross connect which enables conversion between one T1 signal and one E1 signal. T1 and E1 signals with framing employ u-Law and A-Law compander encoding principles respectively and encode those analog (voice) signals into 64kbits digital data. The T1 interface supports D4(SF) or ESF frame formats with B8ZS or AMI line code.
Chapter 1 Introduction 1.7.20 FRM220-1000TS GbE to Gigabit Fiber Converter Card The FRM220-1000T(S) is a 1000Base copper to fiber converter which transparently supports any protocol or packet size. This slide in fiber media converter is available in two different models that work stand-alone or as line cards for placement in the FRM220 Platform Media Converter chassis. The FRM220-1000T uses a fixed optical transceiver while the FRM220-1000TS features an standard SFP socket.
Chapter 1 Introduction 1.7.21 FRM220-4G 2R 4.25G Transponder Card FRM220-4G-2S is a multi-rate, 28M to 4.25G 2R optical repeater device. The "2R" consists of Re-amplification and Re-shaping. The transponder card converts a data signal to the correct wavelength for transmission on a specific channel by supporting SFP optics on both line side and client side interfaces.
Chapter 1 Introduction 1.7.22 FRM220-Serial/FDC RS-485/RS-232 Fiber Ring Converter Card The FRM220-Serial/FDC provides a dual fiber connection converter solution to extend asynchronous RS-485 or RS-232 transmission distance up to 2km over multimode fiber or up to 120km over single mode fiber. The dual fiber inputs allow connecting multiple devices in a cascade or "daisy chain" fashion as well as creating ring architecture for fiber redundancy.
Chapter 1 Introduction 1.7.23 FRM220-FOM04 4xE1/T1 +100M Ethernet Fiber Optical Multiplexer Card FRM220-FOM04 is a modular design for 4xE1/T1 + Fast Ethernet multi-service to dual strand fiber PDH multiplexer. FRM220-FOM04 provides E1/T1 transmission transparently and pure 100Mbps Fast Ethernet simultaneously. The fiber optic line is based on the SFP technology that allows the flexible use of Multimode or Single mode lines and enables the support of different wavelengths and distances.
Chapter 2 Installation Chapter 2 Installation 2.1 Introduction The Installation chapter will cover the physical installation of the FRM220, Rack Mount In-Band Managed Series Fiber Converter Platform Chassis, the electrical connections, interface connections and cabling requirements. A brief overview of the functional components such as main unit and management options will also be outlined in this chapter.
Chapter 2 Installation 2.3.2 Fan Units Removal/Replacement Figure 2-2 Removal/Replacement of FRM220 Fan Units 2.3.3 Line Card Conversion, Stand-alone/Rack The FRM220 Media Converter Line Card may be mounted in the FRM220-CH20 chassis or serve as a standalone unit. When installing in the FRM220-CH01 single slot chassis or FRM220-CH02 dual slot chassis, the outer cover holds the line card. The unit then serves as a stand-alone media converter that can be linked to a line card in the FRM220 chassis.
Chapter 2 Installation 2.4 Electrical Installation With an AC power module, AC power is supplied to the FRM220 through a standard IEC C14 3-prong receptacle, located on the rear of the module. Any national power cord with IEC C13 line plug may be used to connect AC power to the power module. With a DC module, DC -48V is connected to the terminal block located on the rear of the module, observing the proper polarity.
Chapter 2 Installation 2.6 Chassis Cascade The FRM220 chassis may be cascaded in such a manner that only one single IP address is required to manage up to 10 chassis in a single location. The connection diagram is shown below. Each chassis is assigned a unique ID starting at zero for the master chassis and incrementing for each cascaded chassis, up to an ID of nine. The "out" of the parent chassis connects to the "in" of the slave using any standard UTP cable with RJ-45 connectors.
Chapter 2 Installation 2.7 Power Modules Removal/Replacement The Power Supply Modules in the FRM220 are available in two versions, one AC and one DC type. The universal AC version supports input voltages of 100 to 240 (±10% @ ambient temperature) volts at frequencies of 47 to 63 Hertz. The DC version supports either a standard 36 to 60VDC input voltage. Only one power supply module is required to power a completely full rack.
Chapter 2 Installation 2.8 Installation 2.6.1 Line Card Installation The Line Cards for the FRM220 are Fiber Media Converter Cards which slide into the FRM220 chassis, and interface with the pack panel "main board". The back panel provides a connection to the converter cards for power and serial control. The media converter cards are designed to be "hot" swappable, meaning the FRM220 chassis need not be powered off in order to remove or replace a card.
Chapter 3 Management Quick Start Chapter 3. Management Quick Start 3.1 Introduction The information here is only a brief introduction to the management interfaces and methodologies for managing the FRM220. For in-depth use of the management features of the FRM220, please refer to the FRM220 Network Manager Controller User Manual. 3.
Chapter 3 Management Quick Start 3.3.3 TCP/IP Setup From the main menu, use the 'L' key to enter the 'SNMP System Configuration Setup' menu. An example menu is displayed below. 1 2 3 4 5 **************************************** *** CTC UNION TECHNOLOGIES CO., LTD. *** *** FRM220 NMC VER. 2.12 *** **************************************** << SNMP System Configuration Setup of Chassis 0 >> Model = FRM220 S/N = 000000 Target MAC Address = 00:02:ab:06:20:20 <1>: Target IP : 59.125.162.
Chapter 3 Management Quick Start 3.4 Telnet Terminal Use either a Windows® command window or Telnet client application and connect to the FRM220 NMC using the assigned management IP address. The following is an example of a Telnet screen. It is exactly the same as a local serial console screen, only it can be accessed remotely. 3.5 Web Based Manager The FRM220 NMC supports web based management.
Chapter 3 Management Quick Start 3.6 Element Management System (EMS) The objective of an Element Management System is to provide four major functions for telecommunication operators: - Fault Management (FM) - Performance Management (PM) - Configuration Management (CM) - Security Management (SM) CTC Union's EMS is a proprietary management system designed to provision, monitor and maintain multiple equipments designed by CTC Union.
