Owner manual

ManualsBrandsCTEK ManualsPower suppliersLITHIUM XS

EN • 3

RESET

12V/5A

LiFe60

CONGRATULATIONS

To the purchase of your new professional switch mode battery charger. This charger is

included in a series of professional chargers from CTEK SWEDEN AB and represents the

latest technology in battery charging. The LITHIUM XS charger model is designed for

Lithium-ion batteries using LiFePO

technology only. Please check with the battery manufac-

turer for details. Do not use the LITHIUM XS charger for any other battery technology.

CTEK COMFORT CONNECT – eyelet M6

CTEK COMFORT CONNECT

MAINS CABLE

CTEK COMFORT CONNECT – clamp

CHARGE CABLE

SUPPLY PLUG*

* Supply plugs may differ to suit your wall socket.

ERROR LAMP

FULLY CHARGEDREADY TO USE

POWER LAMP

HOW TO CHARGE

1. Connect the charger to the battery.

2. Connect the charger to the wall socket.

3. Follow the 8-step display through the charging process.

The battery is ready to start the engine when STEP 3 is lit.

The battery is fully charged when STEP 7 is lit.

4. Stop charging at any time by disconnecting the mains cable from the wall socket.

RESET-BUTTON

MANUAL

BATTERIES WITH "UNDER VOLTAGE PROTECTION"

Some Lithium-ion batteries have an on-board UVP (under voltage protection) that

disconnects the battery to avoid it becoming too deeply discharged. This prohibits the

CTEK charger from detecting that there’s a battery connected. To bypass this, the bat-

tery charger needs to open the UVP. By pressing the RESET-button for 10 seconds, the

charger opens the UVP. During this process, the charging STEP 7 is lit. Once the UVP has

been opened and the battery is ready to be charged, the charger automatically starts the

charging cycle.

Summary of content (6 pages)

PAGE 1
MANUAL To the purchase of your new professional switch mode battery charger. This charger is included in a series of professional chargers from CTEK SWEDEN AB and represents the latest technology in battery charging. The LITHIUM XS charger model is designed for Lithium-ion batteries using LiFePO4 technology only. Please check with the battery manufacturer for details. Do not use the LITHIUM XS charger for any other battery technology. SUPPLY PLUG* MAINS CABLE HOW TO CHARGE 1.
PAGE 2
ERROR LAMP CONNECT AND DISCONNECT THE CHARGER TO A BATTERY If the error lamp is lit, check the following: INFO If the battery clamps are incorrectly connected, the reverse polarity protection will ensure that the battery and charger are not damaged. 1. Is the chargers positive lead connected to the battery´s positive pole? 2. Is the charger connected to a 12V LiFePO 4 battery? 3. H as charging been interrupted in STEP 1 or 4? Restart the charger by pressing the RESET-button.
PAGE 3
CHARGING PROGRAM BULK ABSORPTION ANALYSE COMPLETION MAXIMIZATION FLOAT PULSE 11 2 3 4 5 6 7 8 CURRENT (A) EN VOLTAGE (V) ACCEPT 5A until 11.0V Limit: Max 30s Increasing voltage to 13.8V 5A Max 10h Declining current 13.8V Max 30h Checks if voltage drops to 12V 3minutes STEP 1 ACCEPT Tests if the battery can accept charge. This step prevents that charging proceeds with a defect battery. STEP 2 BULK Charging with maximum current until approximately 90% battery capacity.
PAGE 4
SAFETY TECHNICAL SPECIFICATIONS Model number 1081 Rated Voltage AC Charging voltage 220–240VAC, 50–60Hz 13.8/14.4 VDC Charging current 5A max Current, mains 0.
PAGE 5
CTEK SWEDEN AB, issues this limited warranty to the original purchaser of this product. This limited warranty is not transferable. The warranty applies to manufacturing faults and material defects for 5 years from the date of purchase. The customer must return the product together with the receipt of purchase to the point of purchase. This warranty is void if the battery charger has been opened, handled carelessly or repaired by anyone other than CTEK SWEDEN AB or its authorised representatives.
PAGE 6
8 • EN