MULTI XS 4003 Battery charger FI NO DK SE NL IT For lead-acid batteries 1.2–140Ah ES FR DE QUICK GUIDE EN ® Model 1035 User’s Manual and a guide to professional battery charging for starter/deep cycle batteries.
QUICK GUIDE MULTI XS 4003 For details – see manual V A Connect the red lead to the positive pole of the battery and the black lead to the negative pole. + – When you are sure the battery leads are correctly placed, connect the charger to the wall socket.
Mains voltage connected Error Battery size 1.2–14Ah A V Battery size 14–140Ah Ready to use Snowflake Battery size 14–140Ah Fully charged Recond Battery size 14–140Ah QUICK GUIDE Settings are made by pressing the “MODEbutton” and stepping forward one press at a time until the required mode is reached, the button is then released.
INTRODUCTION Congratulations on purchasing your new professional switch mode battery charger. This charger is included in a series of professional chargers from CTEK SWEDEN AB and represents the latest technology in battery charging. Please read this user´s manual and follow the instructions carefully. SAFETY • The charger is designed for charging 12V lead-acid batteries. Do not use the charger for any other purpose. • Battery acid is corrosive.
BATTERY TYPES AND SETTINGS EN The MULTI XS 4003 model offer several alternative settings to suit specific charging needs and required functionality. The following recommendations should only be regarded as guidelines. Please observe the battery manufacturer recommendations in the event of uncertainty. Settings are made by pressing the “MODE-button” and stepping forward one press at a time until the required mode is reached, the button is then released.
The table explains the various lamps: Mains voltage connected. If the mode is incorrect, the charger cuts the charging/voltage supply. The charger switches to error mode before starting in the following circumstances: If the battery has been connected with reverse polarity to the charger terminals. The charger’s analysis function has interrupted the charge. The charger has been in start mode for a time that exceeds max time.
If the battery leads are incorrectly connected, the reverse polarity protection will ensure that the battery and charger are not damaged. EN Start charging 1. When you are sure the battery leads are correctly placed, connect the charger to the wall socket. The charger will indicate that the mains voltage is connected. If the battery leads are incorrectly connected, the reverse polarity protection will ensure that the battery and charger are not damaged. The fault indicator lamp will be lit.
Analysis Tests the self-discharge. If the self discharge is too high, the charging is interrupted and error mode indicated. Recond Reconditioning of deeply discharged batteries. This step is used to restore deeply discharged open vented batteries. With increased charging voltage over a limited time, the voltage is allowed to rise so that the battery starts to emit gas. As a result you get a mix in the battery that is good both for its capacity and service life.
The charger is maintenance free. Please note that dismantling the charger is not permitted and will void the warranty. A defective mains cable has to be replaced by CTEK or by a representative authorised by CTEK. Keep your charger clean. Wipe it with a soft tissue and mild cleaning liquid. The charger must be disconnected for cleaning. EN MAINTENANCE EQUIPMENT The MULTI XS 4003 model is delivered with one battery lead with battery clamps and one battery lead with eyelet terminals.
PROGRAM DESCRIPTION Soft start Bulk Absorption Revives a sulphated battery Tests the state of the battery Main charge Top charge and minimal fluid loss Current (A) Voltage (V) Desulphation 10 YES 4A for max 8h until the voltage reaches 12.6V. 4A for max 20h. A combination of current limits and timers, max 10h. YES 0.8A for max 8h until the voltage reaches 12.6V. 0.8A for max 20h. A combination of current limits and timers, max 10h.
Recond Float Pulse Tests whether the battery can retain energy Reconditioning of deep discharged batteries Maintenance for maximum performance Maintenance for maximum service life Alerts the user if the voltage drops to 12V in 3 minutes. Max 15.8V and 1.5A for 4h for deep discharged batteries. Otherwise for 30 minutes (only in RECOND mode). Alerts the user if the voltage drops to 12V in 3 minutes. 13.6V with max 4A for max 10 days. EN Analysis Pulse starts at 12.9V, max voltage 14.4V. 13.
LIMITED WARRANTY CTEK SWEDEN AB, Rostugnsv. 3, SE-776 70 VIKMANSHYTTAN, SWEDEN issues this limited warranty to the original purchaser of this product. This limited warranty is not transferable. The warranty applies to manufacturing faults and material defects for 5 years from the date of purchase. The customer must return the product together with the receipt of purchase to the point of purchase.
