COLOR MONITOR Model No : CTL 5fln USER S GUIDE S/N:9978623807A CTL
IMPORTANT SAFEGUARDS 1. Read all of these instructions. 2. Save these instructions for later use. 3. Unplug this monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use attachments not recommended by the monitor manufacturer as they may cause hazards. 5. Do not use this monitor near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool, etc. 6.
The power cord is used as a main disconnect device. Disconnect the power cord before servicing. The outlet must be installed near the monitor and must be easily accessible. As an ENERGY STAR Partner, Computer Technology Link, Inc., has determined that this product meets the Energy Star guidelines for energy efficiency.
CONTENTS Introduction Product Features Setup INTRODUCTION 1 2 3 Installing the Tilt/Swivel Stand 3 Connecting the D-Sub Signal Cable 4 Connecting to Your Macintosh Computer 4 Connecting the Power Cord 4 Power Management System 5 DDC for Plug & Play 5 Operation & Adjustment 6 Specifications 10 Factory Preset Timings 11 Troubleshooting 12 Description for D-sub Connector 13 This manual explains how to correctly install, operate and get the best performance from your monitor.
SETUP PRODUCT FEATURES INSTALLING THE TILT/SWIVEL STAND • The convenient and user-friendly on-screen display allows for easy and accurate adjustments of horizontal and vertical screen size and position, geometry and screen color. • The monitor supports a safe working environment in strict compliance with the MPR standard for low emissions(TCO 1995 is optional). • The monitor complies with the VESA Display Data Channel(DDC) specification for Plug & Play compatibility.
CONNECTING THE D-SUB SIGNAL CABLE 1. Turn off the computer and monitor. 2. Connect the 15 pin D-sub connector to the output port of the video card in your computer. 3. Tighten the screws of connector. CONNECTING TO YOUR MACINTOSH COMPUTER POWER MANAGEMENT SYSTEM If you use the monitor with a computer which complies with the power saving program, you can set the monitor to go blank when the system has remained unused for a period of time.
OPERATION & ADJUSTMENT 1. OSD(On-Screen Display) Menu 1 EXIT + ADJUST SELECT MENU Adjust the contrast of image, the difference : Launch OSD(On-Screen Display) Menus : Select the next function : Select the previous function : Increase the value of any selected function : Decrease the value of any selected function : Exit OSD Menus & Launch OSD Menus, when no OSD MENU EXIT - + between light and dark areas on the screen. Range : 0 -100 % + Adjust the brightness of the entire display.
2. OSD (On-Screen Display) Menu 2 - + Adjust the position of the display horizontally 3. OSD (On-Screen Display) Menu 3 - (left or right). 50% + 50% PINCUSHION Adjust the left and right margins for more convex or more concave margins. Image turns to by . Image turns to by . HORIZONTAL POSITION - + Adjust the display width (horizontal size). + Adjust the trapezoid of the screen by moving the lines inward or outward. Image turns to by . Image turns to by .
SPECIFICATIONS Picture Tube Video Scan Frequency Type : 15-inch, Flat Square Tube type (14-inch, viewing area) Dot Pitch : 0.28mm, MPR II Face Treatment : Non-glare / Anti-static Input Signal : R.G.B. Analog Amp. Bandwidth : 85 MHz Input Sync : TTL, separate negative / positive Horizontal : 30 - 69 KHz Vertical : 50 - 120 Hz Tilt/Swivel Range Tilt : 5 forward, 10 backward Swivel : 45 leftward, rightward Dimension 368(W) 394(D) 382(H) mm (set with stand) Weight(net/gross) 12.5 / 14.2 Kg 27.6 / 31.
TROUBLESHOOTING DESCRIPTION FOR D-SUB CONNECTOR Symptom No picture. Check Check if POWER SWITCH and COMPUTER POWER SWITCH are in the on position. Check if the signal cable is correctly connected to the video card. Check if the pins of D-sub connector are not bent. Check if the computer is in the power saving mode. Check if POWER SWITCH is in the on position. POWER LED is not lit. Check if the power cord is correctly connected. Image is unstable.