PR711FL User’s Manual U s e r ’ s M a n u a l PR711FL 1
PR711FL User’s Manual Table of Contents 1. Safety Instructions 3 2. Recommendation for Optimum Performance 3. Introduction 4. Installation 6 7 5. Controls and Adjustments 6. Trouble Shooting 7. Energy Declaration 8. Specification 14 18 19 9.
PR711FL User’s Manual Safety Instructions FCC Statement This equipment has been tested to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PR711FL User’s Manual 2. Do not place the monitor or other heavy objects on the power cord. A damaged power cord can cause fires or electrical shock. 3. Keep the monitor away from high-capacity transformers, electric motors and other strong magnetic fields. 4. Do not connect to any voltage or frequency beyond the range specified on the back of the monitor. Please follow all warnings and instructions marked on the product. 5.
PR711FL User’s Manual Recommendation for Optimum Performance Your monitor will provide the best results if you follow these recommendations: 1. Do not use your monitor against a bright background or where sunlight or other light sources will shine directly on the screen. 2. Place the monitor just below eye level (10° -15°) for optimum viewing. 3. Set the monitor brightness level to match the ambient room light. 4.
PR711FL User’s Manual Introduction The monitor is a multiple frequency high-resolution color monitor for IBM compatible PC's or Macintosh and workstation systems. The monitor is equipped with microprocessor based intelligence and multiple frequency scanning capability, allowing it to provide maximum compatibility for various system platforms. The monitor uses the latest screen technology including a 0.24mm AG FD Trinitron® CRT to display crisp text and vivid color graphics.
PR711FL User’s Manual Installation Unpacking Your color monitor package should contain the following items: Color monitor with tilt/swivel base (with Signal cable) Power cord User's Guide / Driver CD System Setup 1. Turn off the system and all attached peripherals. 2. Carefully turn the monitor upside down.
PR711FL User’s Manual Remove the Tilt/Swivel Base 1. Squeeze and hold the latches. 2. Pull the tilt/swivel base to the rear of the monitor and lift to remove the base. Installing the Tilt/Swivel Base 1. Align the base with the slots on the bottom of the monitor and insert the tilt/swivel base into the slots. 2. Push the tilt/swivel base firmly toward the front of the monitor until the latches click into the locked position.
PR711FL User’s Manual Controls and Adjustments Once installation is complete, refer to this section for useful tips on how to use your monitor controls and make adjustments to match your personal preferences. The following indicators, controls and adjustments, including On-Screen Displays (OSD), are accessible from the front of your monitor: Front Panel Controls 1. Power Switch To turn the monitor on or off. 2. Power LED Indicator As long as the monitor is powered, this indicator is lit.
PR711FL User’s Manual 4. Up " " button To adjust the selected OSD function or the contrast directly. 5. Down " " button To adjust the selected OSD function or the brightness directly. 6. "ESC" button To close the OSD manual and to escape function. How to Make On-Screen Display (OSD) Adjustments On-Screen Displays are called up from the front panel controls as noted above. Adjustments are made with " " , " " , " " and "ESC" control switches.
PR711FL User’s Manual A. Status To display existing timing data of resolution and frequency. B. Picture a. Press " " or " " to select Vertical and Horizontal position, Vertical and Horizontal size. b. Press " " to process. c. Press " " or " " to preferred picture. C. Geometry a. Press " " or " " to select Side-pin, Balance, b. Press " " to process. c. Press " " or " " to preferred picture. 11 Keystone, Parallel, Rotate and Corner.
PR711FL User’s Manual D. Color a. Press " " or " " to select various white color temperature standard. b. In User item, presses " " to confirm action color adjustment. c. Press " " or " " to select Red, Green and Blue then press "Enter" to process. d. Press " " or " " increase or decrease density. E. Advanced a. Press " " or " " to select Moire, Converge or b. Press " " to proceed. c. Press " " or " " to preferred picture. E-1. Moire Press " " or " " to reduce Moire. 12 Degauss.
PR711FL User’s Manual E-2. Converage a. Press " " or " " to select Horizontal or Vertical convergence adjustment. b. Press " " to proceed. Caution: 1. If moire reduction is overdone, picture quality, i.e. focus and vertical line stability will both be effected. 2. Proper adjustment is recommended for not effecting picture performance. F. Recall Press " " to confirm window. If this window appears, that means it cannot be preset.
PR711FL User’s Manual Confirm the Recall action by pressing the " " or cancel the action by pressing the "ESC". G. Language Press " " or " " to select the Language for OSD only. (2) Contrast/Brightness: When OSD is off, " " or " " will be adjust contrast or brightness.
PR711FL User’s Manual Trouble Shooting Notify your supervisor or contact your service personal when: • Power cords are frayed or damaged. • Liquid is spilled into the monitor. • The monitor does not operate normally when operating instructions are observed. • The monitor has been dropped or the cabinet has been damaged. Review this list of trouble-shooting tips before contacting an authorized service center. Problem Power Indicator (LED) is not lit.
PR711FL User’s Manual Signal Out of range. Readjust the signal based on spec. Reference "Scan Frequency". Display image is not centered or Refer to "Controls & Adjustments." You need to is too small or too large. adjust "Size" and "Position" of the image. Image is scrolling or is unstable Make sure the signal cable is connected securely to the video card or computer. Picture is fuzzy or color looks Adjust Contrast and Brightness controls. blotchy.
PR711FL User’s Manual Edges of display are curved Refer to "Controls and Adjustments." You need inward or outward. to adjust the "Side Pincushion." No Plug & Play. Verify that the host system is Plug & Play compatible. Check to see if Windows is installed, and the software key for the Data Display Channel (DDC) function is enabled. Determine if original manufacturer's detachable signal cable is being used (D-Sub-15 pin only). Our monitor is build-in FD Trinitron® CRT.
PR711FL User’s Manual Black fine vertical lines are Degaussing the screen. visible on the screen. Shock and vibration may cause the aperture grille misaligned, which results few fine black vertical lines across the screen Tap lightly (do not hit) the side of the monitor. If above mentioned remedies do not work, please do the following: 1.Display full white window or wallpaper background over the area where the black lines appears. 2.
PR711FL User’s Manual Energy Declaration This monitor is equipped with a function for saving energy, which supports the VESA Display Power Management Signaling (DPMS) standard. This means that the monitor must be connected to a computer, which also supports the VESA DPMS standard to fulfill the requirements of the NUTEK specification 803299/94/96. The time settings for switching to a power saving mode are adjusted from the system unit by software.
PR711FL User’s Manual Specification Color Picture Tube 43.1 cm / 17" (16" viewable screen size) diagonal measurement, 90 degree deflection, FD Trinitron® CRT, anti-glare, anti-reflection, anti-static, medium short persistence phosphor, dark bulb AG Pitch 0.24 mm, (at center) Input Signal Analog 0.7V peak to peak separate TTL Positive or Negative Scan Frequency Horizontal: 30 to 97 kHz automatically Vertical: 50 to 160 Hz automatically Max.
PR711FL User’s Manual Reference Information This color monitor supports multiple operating platforms such as IBM compatible and Macintosh family computers. This section provides you with detailed information on pin assignment of the D-Sub connector and the preset timing chart of the prevailing video standards.
PR711FL User’s Manual Preset Timing Chart Note: This monitor is equipped with a microprocessor which allows the user to set his own preferred mode(s) beyond those standard mode listed below. To reduce visual tiredness and eyestrain, it is recommended to choose the highest refresh modes available. Horizontal Resolution Format 640x480@60Hz VGA 31.5 60 720x400@70Hz VGA 31.5 70 800x600@75Hz VESA 46.9 75 800x600@85Hz VESA 53.7 85 832x624@75Hz MAC 49.
