Safety Data Sheet

ManualsBrandsCubitron ManualsDisc Sanders3M Disc Sander Air-Powered, 1 HP, 5 Inch, 12,000 RPM

Rev. 2/19/2015

SANDER INSTRUCTION MANUAL

101 mm (4 in.)–127 mm (5 in.)

12,000 RPM

Important Safety Information

Please read, understand and follow all safety information contained in these instructions prior to the use of this tool.

Retain these instructions for future reference.

Intended Use

This pneumatic tool is intended for use in industrial locations, and used only by skilled, trained professionals in accordance with the instructions in this manual. This

pneumatic tool is designed to be used with disc pads, and appropriate abrasive for sanding metals, wood, stone, plastics and other materials. It should only be used

for such sanding applications and within its marked capacity and ratings. Only accessories specically recommended by 3M should be used with this tool. Use in any

other manner or with other accessories could lead to unsafe operating conditions.

Do not use disc pads that have a Max RPM less than the tool Max RPM rating.

Summary of device labels containing safety information

Marking Description

WARNING: Refer to Instruction Manual

Direction of Rotation

90 psi / .62 Mpa / 6.2 Bars Max Maximum Pneumatic Inlet Pressure

12,000 RPM Maximum Rotational Speed

Use accessories rated at tool RPM or higher Accessories Safety Note

Prolonged vibration may cause injury Vibration Safety Note

Explanation of Signal Word Consequences

W WARNING: Indicates a potentially hazardous situation which, if not avoided, may result in death or serious injury and/or property damage.

W CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or property damage.

W WARNING

To reduce the risks associated with impact from abrasive product or tool breakup, sharp edges, hazardous pressure, rupture, vibration and noise:

• Read, understand and follow the safety information contained in these instructions prior to the use of this tool. Retain these instructions for future reference.

• Only personnel who are properly trained should be allowed to service this tool.

• Practice safety requirements. Work alert, have proper attire, and do not operate tools under the inuence of alcohol or drugs.

• Operators and other personnel must always wear protection for eyes, ears, and respiratory protection when in the work area or while operating this

product. Follow your employer’s safety policy for PPE’s and/or ANSI Z87.1 or local/national standards for eyewear and other personal protective equipment

requirements.

• Wear leather apron or other protective apparel, taking into consideration the type of work being done.

• Never exceed marked maximum input pressure (90psi / .62Mpa / 6.2Bars).

• Proper eye protection must be worn at all times.

• Tool is not to be operated in the presence of bystanders.

• If you notice any abnormal noise or vibration when operating the product, immediately discontinue its use and inspect for worn or damaged abrasive

product or accessories. Correct or replace the suspect component. If abnormal noise or vibration still exists, return the tool to 3M for repair or replacement.

Refer to warranty instructions.

Original Instructions

Summary of content (14 pages)

PAGE 1
SANDER INSTRUCTION MANUAL 101 mm (4 in.)–127 mm (5 in.) 12,000 RPM Important Safety Information Please read, understand and follow all safety information contained in these instructions prior to the use of this tool. Retain these instructions for future reference. Intended Use This pneumatic tool is intended for use in industrial locations, and used only by skilled, trained professionals in accordance with the instructions in this manual.
PAGE 2
W WARNING • • • • • Never operate this tool without all guards or safety features in place and in proper working order. Make sure the tool is disconnected from its air source before servicing, inspecting, maintaining, cleaning, and before changing abrasive product. Only use abrasive disc pads and other accessories supplied by 3M. Never use this tool with bonded abrasive products, such as grinding wheels, that require a guard.
PAGE 3
Parts Page PARTS LIST FOR 3M PN 28408, 12000 RPM, 4"–5" SANDER 19 20 22 23 18 USE 3M TL62 THREADLOCKER TO 15-20 FT-LB 9 USE 3M TL62 THREADLOCKER TO 90-130 IN-LB 10 11 17 8 14 13 6 5 4 3 15 16 12 4 LUBRICATE GEARS FUCHS RENOLIT A X S2 OR EQUAL 21 33 34 32 7 2 USE 3M TL62 THREADLOCKER TO 20-25 FT-LB 30 28 29 38 37 41 42 31 25 26 27 24 35 36 40 39 1 INSTALL WITH BEVEL FACING OUT Fig.
PAGE 4
Parts Page PARTS LIST FOR 3M PN 28622, 12,000 RPM, 5" SANDER USE 3M TL62 THREADLOCKER TO 90-130 IN-LB FILL WITH COUPLING GREASE USE 3M TL62 THREADLOCKER TO 90-130 IN-LB 9 USE 3M TL62 THREADLOCKER TO 20-30 FT-LB 4 10 11 11 8 12 13 7 LUBRICATE FUCHS RENOLIT A X S2 OR EQUAL 3 2 16 21 17 27 29 28 23 24 41 51 39 33 32 31 30 USE 3M TL62 THREADLOCKER TO 30-40 FT-LB 26 25 5 4 22 19 18 14 11 6 15 20 34 35 40 43 44 42 48 46 47 45 50 49 USE 3M TL62 THREADLOCKER TO 20-25 FT-LB 38 36
PAGE 5
Product Configuration/Specifications: Model Number Disc Size mm (in.) Speed RPM Net Wt. kg. (lb.) Height mm (in.) Length mm (in.) *Noise Level dBA Pressure (Power) **Vibration Level m/s2 (ft/s2) **Uncertainty K m/s2 28408 102–127 (4–5) 12,000 1.05 (0.48) 114 (4.5) 216 (8.5) 83.8 (95.4) 7.4 (24.3) 0.04 28622 102–127 (4–5) 12,000 1.83 (0.83) 119 (4.7) 292 (11.5) 86.0 (94.6)† 5.7 (18.7)† 0.05† Noise and Vibration values are derived from testing of mechanically identical tools.
PAGE 6
Safety Precautions 1. Read all instructions before using this tool. All operators must be fully trained in its use and aware of these safety rules. 2. The tool RPM should be checked on a regular basis to ensure proper operating speed. 3. Make sure the tool is disconnected from the air supply. Attach the 3M™ Disc Pad to the sander adaptor using the wrenches supplied with the tool. Select a suitable abrasive and secure it to the disc pad. 4. Always wear required safety equipment when using this tool. 5.
PAGE 7
Product Use: All statements, technical information and recommendations contained in this document are based upon tests or experience that 3M believes are reliable. However, many factors beyond 3M’s control can affect the use and performance of a 3M product in a particular application, including the conditions under which the 3M product is used and the time and environmental conditions in which the product is expected to perform.
PAGE 8
MANUAL DE INSTRUÇÃO DE LIXADEIRA 101 mm (4 pol.)–127 mm (5 pol.) 12.000 RPM Informações de Segurança Importantes Leia, compreenda e siga todas as informações de segurança contidas nestas instruções antes de utilizar esta ferramenta. Guarde estas instruções para referência futura. Uso Pretendido Esta ferramenta pneumática é feita para uso em locais industriais e para ser usada por profissionais capacitados e treinados, de acordo com as instruções neste manual.
PAGE 9
W AVISO • • • • • Nunca opere esta ferramenta sem todas as guarnições ou elementos de segurança colocados e em condição operacional adequada. Assegure que a ferramenta esteja desconectada de sua fonte de ar antes do reparo, inspeção, manutenção, limpeza e antes de trocar o produto abrasivo. Use apenas suportes de disco abrasivos e outros acessórios fornecidos pela 3M. Nunca use esta ferramenta com produtos abrasivos colados, tais como discos abrasivos, que exigem uma proteção.
PAGE 10
Página de peças LISTA DE PECAS PARA LIXADEIRA PN 28408, 12000 RPM, 4"–5" 19 20 USAR ROSCA 3M TL62 PARA 15-20 FT-LB 22 23 18 9 USAR ROSCA 3M TL62 PARA 90-130 IN-LB LUBRIFICAR ENGRENAGEM COM “FUCHS RENOLIT A X S2” OU SIMILAR 21 10 4 6 5 4 3 11 17 8 13 14 15 16 12 33 32 7 31 25 26 27 24 2 38 37 41 42 USAR ROSCA 3M TL62 PARA 20-25 FT-LB 30 28 29 34 35 36 40 39 1 INSTALE CON EL BISEL HACIA AFUERA Fig.
PAGE 11
Página de peças LISTA DE PEÇAS PARA LIXADEIRA PN 28622, 12000 RPM, 5" 20 USAR ROSCA 3M TL62 PARA 90-130 IN-LB PREENCHER COM GRAXA 17 USAR ROSCA 3M TL62 PARA 90-130 IN-LB 9 USAR ROSCA 3M TL62 PARA 20-30 FT-LB 4 10 11 11 8 12 13 7 3 2 21 16 27 29 28 23 24 41 51 39 33 32 31 30 USAR ROSCA 3M TL62 PARA 30-40 FT-LB 26 25 5 4 LUBRIFICAR ENGRENAGEM COM “FUCHS RENOLIT A X S2” OU SIMILAR 19 18 14 11 6 15 22 43 44 42 40 34 35 48 46 47 45 50 49 USAR ROSCA 3M TL62 PARA 20-25 FT-LB 38 36
PAGE 12
Configuração/Especificação do Produto Número do modelo Tamanho do disco mm (pol.) Velocidade de RPM Peso líquido do produto kg. (lb.) Altura mm (pol.) Comprimento mm (pol.) *Nível de ruído dBA Pressão (Potência) **Nível de vibração m/s² (ft/s²) **Incerteza K m/s² 28408 102–127 (4–5) 12,000 1.05 (0.48) 114 (4.5) 216 (8.5) 83.8 (95.4) 7.4 (24.3) 0.04 28622 102–127 (4–5) 12,000 1.83 (0.83) 119 (4.7) 292 (11.5) 86.0 (94.6)† 5.7 (18.7)† 0.
PAGE 13
Precauções de Segurança 1. Leia todas as instruções antes de usar esta ferramenta. Todos os operadores devem estar plenamente treinados em seu uso e cientes destas regras de segurança. 2. O RPM da ferramenta deve ser verificado regularmente para garantir a velocidade operacional correta. 3. Certifique-se de que a ferramenta esteja desconectada do suprimento de ar. Anexe o suporte de disco da 3M™ ao adaptador da lixadeira utilizando as chaves fornecidas com a ferramenta.
PAGE 14
Uso do produto: Todas as instruções, informações técnicas e recomendações contidas neste documento se baseiam em testes ou experiência que a 3M acredita serem confiáveis. No entanto, vários fatores além do controle da 3M podem afetar o uso e o desempenho de um produto 3M em uma aplicação específica, incluindo as condições sob as quais o produto 3M é usado e as condições de tempo e ambientais nas quais o produto deve funcionar.