Installation & Assembly

ManualsBrandsCuisinart ManualsHanging Pot RacksOctagonal Hanging Rack

Brushed Stainless Steel

Octagonal Hanging Cookware Rack

Model CRC-29B

Beautifully display Cuisinart

Cookware and keep

it within easy reach. This Cuisinart

Brushed

Stainless Cookware Rack eliminates the need to

bend down to stack and store cookware in

cupboards. The solid brushed stainless rack is

easy to install and is designed to last a lifetime.

Enclosed you will ﬁnd everything needed for the proper assembly and use of your cookware rack. Two people make

assembly and installation easier. The parts and hardware included are:

(1) Octagonal Base (3) Hanger Arms (5) Grid (7) Ceiling Screw Hooks

(2) Pot Hooks (4) Allen Head Bolts (6) Nuts with lock washers (8) Allen Head Wrench

ASSEMBLY and INSTALLATION INSTRUCTIONS

Please proceed carefully, using the following instructions to assure this rack is assembled properly for safe installation and

use, and without damage to the ﬁnish. Haste in assembly could result in needless scratching or marring of the stainless

steel ﬁnish.

1. Unwrap rack base and grid from plastic covering. Notice that each hanger arm has one hole on one

end and two different sized holes at the other end. The end with one hole is the end that attaches to the

octagonal base. Notice also that two of the hanger arms have a threaded hole at the end with two holes.

2. Join the two hanger arms with the unthreaded holes to the two hanger arms with the threaded holes

by placing an allen head bolt through the unthreaded hole to the threaded hole in each set. Leave the

screw loose (diagram A).

3. Place the octagonal base on a ﬂat surface. Next attach the arm sets to the base by placing them directly

over the mounting holes on the base. (Make sure that the allen head bolts at the top of the arm sets are both

showing from the same side of the rack.) Attach the four remaining allen head bolts going from the out-

side of the hanger arms to the inside of the base. Make sure that the arm sets are at right angles to the base,

and then tighten all the screws using the allen head wrench provided. Thread the two nuts onto the ends of the joined

hanger arms and tighten.

4. Place the grid on the octagonal base resting on the allen head bolts. Assembly is now complete and your cookware rack

is ready to hang.

5. Your rack must be anchored into the solid wood of ceiling joists or beams – to install otherwise is improper.

Plasterboard or wall fasteners will not work and should not be used. Carefully measure the area where the rack is to

be hung. The ceiling screw hooks should be 16" apart.

6. Install your ceiling screw hooks. Your local hardware store can advise you if special hardware is needed for your

particular kitchen.

7. Hang your pot hooks from the interior grid only. Do not hang them from the perimeter or the cut portion of the grid.

Distribute cookware evenly.

8. Use a low-abrasive product to clean your cookware rack. A periodic cleaning will restore the stainless steel to its

original brilliance.

WARNING It is important that your cookware rack be assembled and installed according to the above directions. If the

unit is assembled and or installed incorrectly, it could become unstable, collapse and possibly cause injury. Cuisinart is not

responsible for any damages due to improper assembly or installation.

WARNING:

PLEASE READ ALL INSTRUCTIONS

BEFORE ASSEMBLING AND INSTALLING

YOUR NEW COOKWARE RACK

Rack Size: 31½" Length x 15½" Width x 19" Height

Diagram A

Pot Hook

Nut

Grid

Ceiling Hook

Base

Allen Head Bolt

Hanger

Arm

OVER PLEASE

Summary of content (2 pages)

PAGE 1
5 2 Pot Hook Brushed Stainless Steel Octagonal Hanging Cookware Rack Model CRC-29B Beautifully display Cuisinart® Cookware and keep it within easy reach. This Cuisinart® Brushed Stainless Cookware Rack eliminates the need to bend down to stack and store cookware in cupboards. The solid brushed stainless rack is easy to install and is designed to last a lifetime.
PAGE 2
Lifetime Warranty Your Cuisinart® Cookware Rack is warranted to be free of defects in material and workmanship under normal home use from the date of original purchase throughout the original purchaser’s lifetime. If your cookware rack should prove to be defective within your lifetime, we will repair it (or, if we think it necessary, replace it) without charge to you, except for shipping and handling.