Twin Oaks Dual Function Grill ASSEMBLY INSTRUCTIONS Model GAS0356AS / GAS0356ASO
ASSEMBLY INSTRUCTIONS: READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.
14 16 17 13 18 22 19 20 25 21 23 15 29 28 26 30 31 11 27 8 10 12 1 7 32 2 33 4 3 6 5 9 24 2
Step 1 • Remove 2 screws • Attach FRONT PANELS 1 and 2 • Tighten 2 screws 1 2 Step 2 • Loosen 6 screws 3-4 turns on FRONT LEGS 3 and 4 1 2 • Do not remove screws • Attach FRONT PANELS 1 and 2 using keyholes • Tighten 6 screws 4 3 NOTE: Before tightening keyhole screws, make sure panels are aligned.
Step 3 • Loosen 6 screws 3-4 turns on FRONT LEGS 3 and 4 • Do not remove screws • Attach RIGHT SIDE FRONT PANEL 5 and LEFT SIDE FRONT PANEL 6 • Tighten 6 screws on RIGHT SIDE FRONT PANEL 5 and LEFT SIDE FRONT PANEL 6 1 2 6 4 3 5 Step 4 • Loosen 2 screws • Attach LEFT SIDE PANEL 7 • Tighten 2 screws on LEFT SIDE PANEL 7 1 6 5 2 3 4 7 4
Step 5 • Loosen 2 screws 1 • Attach CART BRACE 8 8 5 • Tighten 2 screws on CART BRACE 8 • Remove 4 screws 2 6 4 3 7 Remove 2 screws Remove 2 screws Step 6 • Attach CART BASE 9 • Tighten 4 screws (Removed from Step 5) 8 1 6 5 2 4 3 7 9 5
Step 7 11 • Loosen 9 screws on REAR LEGS 10 and 12 • Attach BACK PANEL 11 to REAR LEGS 10 and 12 10 12 • Tighten 5 screws • Remove 4 screws Remove 2 screws Remove 2 screws Step 8 9 • Attach CART BASE 9 to rear legs • Tighten 4 screws (Removed from Step 7) 10 12 11 6
Step 9 • Attach LEFT SIDE PANEL 6 and CART BRACE 8 • Tighten 4 screws Tighten 4 screws 7 8 Step 10 • Lock CASTERS 24 • Attach CASTERS 24 to legs 24 unlocked locked 7 CASTERS
Step 11 • Loosen 2 screws • Install TANK BLOCK BAR 33 • Tighten screws 33 Step 12 • 32 ACCESSORY HOOKS Attach ACCESSORY HOOKS 32 to LEFT SIDE PANEL 7 with wing nuts 7 8
Step 13 • Loosen 5 screws • Remove 2 screws Remove 2 screws Loosen 5 screws Step 14 • Loosen 1 screw • Remove 2 screws Loosen 1 screw 9 Remove 2 screws
Step 15 13 CART BRACKETS • Set GRILL BODY 13 on cart • Make sure screw drops into rear cart brackets • Push GRILL BODY 13 to back of cart • Install 2 screws in FRONT BRACKETS (Removed from Step 13 and Step 14) • Tighten 4 screws on cart brackets (2 screws left over will be used in future steps) CART BRACKETS Step 16 14 • Install HOOD HANDLES 14 (Wing nuts, bezels and washers are pre-installed on handles) 10
Step 17 • Loosen 2 screws • Attach RIGHT SIDE CONTROL PANEL 20 to RIGHT SIDE TABLE 18 using keyholes • Tighten 2 screws • Remove 2 screws and washer Remove screw and washer Loosen screws 20 18 Step 18 • Attach RIGHT SIDE TABLE 18 to GRILL BODY 13 using keyholes • Do not tighten screws at this time • Install and tighten 2 screws (Removed from Step 13 and Step 17) 18 13 Install screws 11 Remove screw
Step 19 Install screw and washer • Install screw and washer (Removed from Step 17) • Make sure control panels are aligned • Tighten 5 screws from Step 18 and Step 19 Align Panels Step 20 Loosen 2 screws A • Remove WING NUT and SIDE BURNER • Loosen 2 screws from SIDE BURNER VALVE A • Install SIDE BURNER VALVE using keyholes in RIGHT SIDE CONTROL PANEL 20 and tighten screws B • Install SIDE BURNER and make sure BURNER VENTURI fits over VALVE NOZZLE C • Tighten WING NUT C C WING NUT B 20
Step 21 • Attach ELECTRODE WIRE to IGNITOR Step 22 • Attach CONTROL KNOB 15 15 13
Step 23 • Loosen 2 screws from LEFT SIDE CONTROL PANEL 19 • Remove 1 screw 19 Remove screw Step 24 • 19 Attach LEFT SIDE CONTROL PANEL 19 to PELLET HOPPER using keyholes 14
Step 25 • Install and tighten 2 screws (Removed from Step 14 and Step 23) Step 26 • Remove 4 screws and washers from AUGER HOUSING 31 • Loosen 1 screw Loosen screw 31 Remove 4 screws 15
Step 27 31 • Install AUGER HOUSING 31 using keyhole in firebox and slots in pellet hopper bracket • Tighten 5 screws and washers in firebox Step 28 • Remove 2 screws • Attach CORD WRAP 26 using 2 screws 26 16
Step 29a • Connect wiring for Controller and Pellet Sensor • These wires can only be connected one way • Make sure the connectors are lined up properly before tightening Step 29b • Once connected, twist to tighten Step 29c • 17 Secure wiring with cord clip.
Step 30 • Install SIDE BURNER GRATE 17 17 Step 31 • Attach HEAT BAFFLE 27 27 18
Step 32 • Install HEAT PLATE 28 on welded brackets 28 Step 33 • Install HEAT TENTS 29 above each burner 29 19
Step 34 • 25 Install COOKING GRATES 25 25 Step 35 • 22 Install WARMING RACKS 22 22 20
Step 36 • Install ASH CATCHER 23 23 Step 37 • Install GREASE TRAY 30 and GREASE CUP 21 through back of grill 30 21 21
Step 38 • Store GRIDDLE 34 on ACCESSORY HOOKS 32 34 22
Model GAS0356AS / GAS0356AS0 Assembled OM0356AS/ASO 1019 ©2019 The Boltz Group LLC Carrollton, Texas 75006 U.S.A.
