Service Manual
ISB, ISBe and QSB (Common Rail [...] Crankcase Blowby, Measure
Section 14 - Engine Testing - Group 14 Page 14-53
To buy Cummins Parts and Service Manuals, Training Guides, or Tools go to our website at https://store.cummins.com
Piston or piston rings are worn or damaged.
• Use the following procedure in the C Series Engines Troubleshooting
and Repair Manual, Bulletin 3666003. Refer to Procedure 001-043 in
Section 1.
• Use the following procedure in the B3.9, B4.5, B4.5 RGT, and B5.9
Service Manual, Bulletin 3666087. Refer to Procedure 001-043 in
Section 1.
• Use the following procedure in the ISB and QSB5.9-44 Engines
Troubleshooting and Repair Manual, Bulletin 3666193. Refer to
Procedure 001-043 in Section 1.
• Use the following procedure in the ISBe, ISB, and QSB (Common Rail
Fuel System) Service Manual, Bulletin 4021271. Refer to Procedure
001-043 in Section 1.
• Use the following procedure in the Industrial QSB3.9-30, QSB4.5-30,
and QSB5.9-30 Series Engines Troubleshooting and Repair Manual,
Bulletin 4021398. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISC, ISCe, QSC8.3, ISL, ISLe3,
ISLe4 and QSL9 Engines Troubleshooting and Repair Manual, Bulletin
4021418. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISC and ISL CM2150 Service
Manual, Bulletin 4021569. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISB CM2100 and CM2150 Service
Manual, Bulletin 4021578. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISBe and ISDe CM2150 Service
Manual, Bulletin 4021597. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISLe CM2150 Service Manual,
Bulletin 4021630. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISL G CM2180 Service Manual,
Bulletin 4021649. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISF3.8 CM2220, ISF3.8 CM2220 AN
and ISF3.8 CM2220 IAN Service Manual, Bulletin 4021704. Refer to
Procedure 001-043 in Section 1.
• Use the following procedure in the ISB4.5, ISB6.7, ISD4.5 and ISD6.7
CM2150 SN Service Manual, Bulletin 4022188. Refer to Procedure
001-043 in Section 1.
• Use the following procedure in the ISF2.8 CM2220, ISF2.8 CM2220 E,
ISF2.8 CM2220 AN and ISF2.8 CM2220 IAN Service Manual, Bulletin
4022178. Refer to Procedure 001-043 in Section 1.Refer to Procedure
001-043 in Section 1.
• Use the following procedure in the ISB6.7 Service Manual, Bulletin
4022254. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISB6.7 CM2350 B101 Service
Manual, Bulletin 2883567. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISB4.5 CM2350 B104 Service
Manual, Bulletin 4332646. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISB6.7 CM2350 B103 Service
Manual, Bulletin 4332641. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the QSB6.7 CM2350 B105 Service
Manual, Bulletin 4332778. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the QSL9 CM2350 L102 Service Manual,
Bulletin 4332796. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISF3.8 CM2220 F110 Service
Manual, Bulletin 4358480. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the ISL9 CM2350 L101 Service Manual,
Bulletin 4310787. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the QSL9 M CM2250 L106 Service
Manual, Bulletin 4358343. Refer to Procedure 001-043 in Section 1.
• Use the following procedure in the QSB6.7 CM2350 B112 Service
Manual, Bulletin 4358498. Refer to Procedure 001-043 in Section 1.