Installation Instructions

ManualsBrandsCurrent Lighting Solutions ManualsElectrical EquipmentDaintree Wireless Wall Dimmer

Product Overview

The Daintree® Wireless Wall Dimmer is a battery-powered wall switch for use in a Daintree Networked or Daintree EZ

Connect application. The WWD2-4IW device installs into an existing junction box to replace the existing wall-mounted

switch with a wireless solution that enables dimming and on/off commands to be delivered to the luminaires in its

commissioned space. The communication with the Daintree system utilizes a secure and reliable wireless connection

which helps minimize installation costs and complexity.

Summary of content (8 pages)

PAGE 1
Product Overview The Daintree® Wireless Wall Dimmer is a battery-powered wall switch for use in a Daintree Networked or Daintree EZ Connect application. The WWD2-4IW device installs into an existing junction box to replace the existing wall-mounted switch with a wireless solution that enables dimming and on/off commands to be delivered to the luminaires in its commissioned space.
PAGE 2
Daintree® Networked Wireless Wall Dimmer (WWD2-4IW) Installation Guide Installation of Back Housing onto Junction Box 1 4 Disconnect power to the junction box Reconnect wires (previously connected to wall switch) with wire nuts. 2 5 Remove the junction box cover plate For proper installation into a dual gang junction box, the tabs between adjacent back housings must be removed. Carefully observe the correct orientation (the UP arrow should be in the upper right corner on each back housing).
PAGE 3
Daintree® Networked Wireless Wall Dimmer (WWD2-4IW) Installation Guide Installation 1 4 Use a standard screwdriver to remove the devices from the back housing Install the main body of the device into the back housing. 2 Separate the battery cover from the device. Pull the plastic insulation strip out of the battery compartment. Put the battery cover back on the device. 5 Install the faceplate onto the device. Note: Device supports the use of other standard faceplates on the market.
PAGE 4
Daintree® Networked Wireless Wall Dimmer (WWD2-4IW) Installation Guide Personality Change 1 Hold the reset button and 2nd button for 5sec to change the personality to dual zone mode. 2 Hold the reset button and 4th button for 5sec to change the personality to scene mode. 2 Remove the individual buttons and replace with the new set of buttons.
PAGE 5
Daintree® Networked Wireless Wall Dimmer (WWD2-4IW) Installation Guide Battery Replacement 1 4 The device’s LED flashing every 30 seconds indicates that the batteries need to be replaced. Install the main body of the device into the back housing. 2 Remove the device from the back housing. 5 Install the faceplate onto the device. The device will rejoin its network automatically. Product Dimensions 5 3 Separate the battery cover from the device. Replace the batteries with AAA batteries.
PAGE 6
Daintree® Networked Wireless Wall Dimmer (WWD2-4IW) Installation Guide Product Operation Button Functionality First Button Short press Double short press Hold Lights ON at previous level Lights ON at 100% output Turn ON and dim up Second Button Lights OFF Lights ON at the lowest output Dim down when lights ON Short press Double short press Hold Third Button Lights ON at previous level Lights ON at 100% output Turn ON and dim up Short press Double short press Hold Forth Button Short press Double
PAGE 7
Daintree® Networked Wireless Wall Dimmer (WWD2-4IW) Installation Guide Technical Data Product Specifications Dimensions 114mm H x 70mm W x 36mm D Weight 130g Power Supply (4) AAA1.
PAGE 8
Daintree® Networked Wireless Wall Dimmer (WWD2-4IW) Installation Guide Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Information Product Name: Wireless Wall Dimmer Model No: WWD2-4IW Supplier’s Name: Current Lighting Solutions, LLC Supplier’s Website: www.gecurrent.com Supplier’s Address (USA): Cleveland, Ohio Supplier’s Phone: 1-866-855-8629 This device complies with part 15 of the FCC Rules.