PLEASE DO NOT RETURN THIS SCOOTER TO THE STORE. For questions or assistance on assembly, contact Currie Technologies® Customer Service toll free at Contents Customer Service.................................................................................3 Technical Information..........................................................................4 (800) 377-4532 Scooter Components...........................................................................5 Scooter Assembly..............................
PUSH TO START Scooter Components “Top cap” 1. Flip the power switch ON. The switch will glow. 2. Push scooter to kick-start motor 3. Put your foot on the deck and GO!!! Handlebar Brake lever Scooter must be moving forward at about 2mph (3 km/h) before motor will activate Throttle Steering mast Technical Information Minimum Rider Age 8 years old Maximum Rider Weight 150 lb. (68 kg) Maximum Speed* 10 mph (16 kph) Maximum range* 5 miles (8 km) Battery 24V 4.
If your scooter’s handlebar is welded to the steering mast, please skip this page and proceed to step 3 Assembling your Ez3 NANO 1. Slide the steering mast onto the scooter frame. Make sure the silver locking pin engages, then close the quick release securely to hold the mast in place. See the next section of this manual for more information on properly tightening quick release clamps. 2. Remove the two bolts holding the top cap onto the steering mast.
3. Before riding for the first time, you should check the tightness of all nuts and bolts on the scooter. Most important are the front wheel axle nuts, any nuts or bolts around the rear brake, the motor, and the rear wheel. Make sure the brake levers and throttle are secure on the handlebars; if they can be twisted out of alignment, their mounting bolts need to be tightened. 4.
Properly adjusting the steering mast quick release clamp On the EZ3Nano, the steering mast is clamped in place by the force of the quick release cam lever pushing against one side of the clamp and pulling the tension adjusting nut, by way of the skewer, against the other. The amount of clamping force is controlled by the tension adjusting nut.
Scooter Use Safety Guidelines Before riding your scooter for the first time, you should fully charge the battery. This may take up to 8 hours. See the section of this manual on battery charging for more information. Turn the scooter on by flipping the power switch on the deck. Limitations of Safety and Warning Notices This owner’s manual includes important safety guidelines and maintenance instructions.
Never operate this product without proper training or instructions. A child under 8 years old should never operate this product. Rider age does not necessarily mean that they are qualified to operate this product. A parent should never allow this product to be used by an individual not having the ability, coordination, maturity, skills and strength to operate it safely and in a controlled manner. Maximum rider weight is 150 lbs (68 kg); never exceed it.
Battery care Proper maintenance of batteries will maximize their lifespan and capacity. Currie Technologies® warranties your new batteries from the date of purchase only if properly cared for—refer to the limited warranty for details. Currie uses SLA (Sealed Lead Acid) batteries in the EZ3Nano scooter. This is a very user-friendly type of battery when cared for properly. Care • Always be sure to turn the bike/scooter power switch to “OFF” after each use.
Battery FAQ Battery charging Q: Do I need to “break-in” my batteries? A: Yes, it is recommended that you perform a “break-in” cycle consisting of ~ three discharge/charge cycles to allow your batteries to reach optimum performance. This involves three complete discharges and three complete recharges. After this initial “break-in” cycle the batteries will have maximum possible performance and less line voltage fluctuations under load.
Brake adjustment Maintenance Regularly checking your scooter and performing maintenance will greatly extend its useful life, and ensure the scooter remains safe to ride. Before each ride, make sure that... ...the steering mast quick release is tight, and the handlebar cannot turn away from the wheels. ...the front wheel axle nuts are tight. ...the front and rear wheels are not cracked or damaged. ...the rear brake operates normally. ...
Replacing the brake cable: 2 Lever barrel adjuster 3 If the brake lever on your scooter becomes stiff and difficult to operate, the brake cable may have become rusted or dirty inside its housing. You can easily replace the brake cable to get back to “like new” performance. The EZ3Nano uses a standard bicycle brake cable and cable housing that can be purchased inexpensively at any bike shop.
After owning the scooter for a while, the brake lever becomes stiff and difficult to operate • See instructions on page 22 for help cleaning or replacing your brake cable. Troubleshooting Scooter will not function • Charge battery for the full recommended time (6-8 hours) • Check connections to the scooter controller, located under the deck near the battery. Scooter suddenly stops working during use • Check fuse, located near the charger port (see diagram on page 5).
Warranties are limited to replacement of parts and/or products determined by Currie, at its sole discretion, to be defective. In cases where multiple components are missing, you may be redirected to the retailer for assistance. Currie will not be responsible for labor costs or repairs. LIMITED WARRANTY EZIP ELECTRIC SCOOTERS Purchased within the United States Currie Tech Corp.
Addt’l SAFETY INSTRUCTIONS ! WARNING »» »» »» »» »» »» These instructions update the owner’s manual to ASTM F2642 standard. Failure to read, understand and follow the instructions in this manual may lead to serious injury or even death. Do not allow hands, feet, hair, body parts, clothing, or similar articles to come in contact with moving parts, wheels or drivetrain, while the motor is running. Make sure that the areas that the scooter is to be used in is safe and suitable for safe operation.
9453 Owensmouth Ave. Chatsworth, CA 91311 Phone: +1 800.377.4532 Fax: +1 818.734.8199 www.CurrieTech.