Installation Guide

Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
HEX BOLT
M10 - 1.25 x 2521
CONICAL TOOTHED WASHER3/8"22
NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ20-0006243
BOLT, CAR,1/2-13 UNC,4-1/2,GRD8,YZ
10-1029744
.250" SPACER PLATECM-12048-SP25
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
WARNING: ALL NON-TRAILER (WHEEL-LESS) LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
WARNING: ** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY **
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
3,500 350
28
15
MITSUBISHI OUTLANDER SPORT/RVR
12/11/2019
12048
30
Scan
for more
information
- NO DRILLING REQUIRED
- TOW LOOP REMOVAL
- TRIMMING REQ ON 2020 MY
3
5
4
1
2
1. Remove (3) bolts and tow loop from the passenger side frame rail. Return bolts and tow loop to owner.
2. Insert 1/2-13 X 4 1/2" carriage bolts and CM-12048-SP spacers through the existing holes in the side of the frame rails, as shown.
After bolts are inserted push them back so the end is flush with the inside of the frame rails. Note: On the driver side you will have
to reach between the bumper cover and rear wheel well to access the holes in the side of the frame rail. Temporary lowering of the
charcoal canister on the driver side will ease installation.
3. Note: On 2020 or newer model years, fascia trimming may be required. Using a dremel tool or aviation shears, trim the fascia as shown in
the trim diagram on both driver and passenger side of vehicle.
4. Raise the hitch into position and slide the bolts in the side of the frame rails through the holes in the hitch. Loosely secure hitch with
1/2" hex flange nut. Note: The carriage bolts should sit flat on the spacers. Note: For ease of installation raise the driver side into
position first, then raise the passenger side.
5. Align the bottom tabs of the hitch with the weldnuts in the frame rails and secure with M10-1.25 x 25mm bolts and 3/8" conical
toothed washers.
6. Reinstall charcoal canister removed in step 2.
7. Torque all 10mm hardware to 48 ft-lbs.
Torque all 1/2" hardware to 110 ft-lbs.
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
EXISTING TOW
LOOP BOLTS
EXISTING WELDNUT
(BOTH SIDES)
EXISTING TOW
LOOP BOLT
EXISTING
TOW LOOP
EURO MOUNT OPTION AVAILABLE
#45571 (1-7/8" BALL) #45572 (2" BALL)
DESIGNED FOR USE WITH
BALLMOUNT #45501
1
CHG TO GRADE 8 TORQUE SPECS
10/5/2012 AJP
REVISION HISTORY
REV DESCRIPTION DATE APPROVED
TOOLS REQUIRED
TORQUE WRENCH
RATCHET
14mm SOCKET
17mm SOCKET
19mm SOCKET
3/4" SOCKET
6" EXTENSION
AVIATION SHEAR
ROTARY TOOL
TRIM DIAGRAM
1.50
.25