Owners manual

Parts List
DESCRIPTIONPART NUMBERQTYITEM
HEX FLANGE NUTHFN 121361
HEX NUT
3/8 - 16
32
HEX BOLT3/8 - 16 x 1 1/413
WASHER3/8"
14
CONICAL TOOTHED WASHER3/8"
65
U-BOLT3_8-16 x 1.75 x 2.5016
HEX NUTM8-1.2517
HEX BOLTM8-1.25 x 3518
HEX BOLTM8 - 1.25 x 2019
CARRIAGE BOLT1/2-13 x 1 3/4610
PLATE .250" A-36 H.R. (COMMERCIAL QUALITY)CM-12101-MP111
INSTALLATION TEMPLATE (NOT SHOWN)CM-12101-TMP
112
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY AUXILIARY STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT:
LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
3500 350
39
45
10/15/2012
12101
90
36170
1) Remove two fasteners that attach the passenger's side bumper bracket to the frame rail end cap. Return fasteners to vehicle owner.
Remove the existing driver's side inboard frame rail end cap bolts and replace it with fastener shown. Remove spare tire cover and pull
the trunk carpeting back to expose the driver's side of the trunk pan.
2) Cut along dotted lines of template. Place template inside trunk on driver's side of spare tire well. Template should be positioned so that the
arrows line up with the center of ribs in the trunk pan. Tape template in place once the arrows are lined up.
3) Center punch three places as specified on the template. Remove template and drill three 1/8" holes through trunk at punched locations.
4) Lift the hitch into position & loosely fasten M8 & 3/8" fasteners provided through passenger side end cap. (Note: If necessary enlarge
existing holes in vehicle end cap for 3/8" fastener.)
5) Check the alignment of the 1/8" drilled holes in the trunk pan. Make adjustments as necessary and enlarge holes to 1/2".
6) Using the hitch as a template mark the passenger side frame rail for drilling. Remove the hitch and drill two 1/2" holes thruough the
passenger side frame rail. Install the 3/8" U-bolt in the previously drilled holes.
7) Reinstall hitch being careful not to knock the U-bolt into the frame rail. Loosely install the 3/8" conical washers, and nuts & M8 fasteners
provided.
8) Position reinforcement plate inside trunk , aligning the notch with the sealed drain hole and making sure the holes in the plate line up with
the holes enlarged in step 5.
9) Install 1/2" carriage bolts down thru reinforcment plate, trunk pan, into hitch and fasten with flange nuts.
10) Using reinforcement plate as a template, drill three 1/2" holes through the trunk pan. Install remaining 1/2" carriage bolts and fasten with
flange nuts. Notes: (1) It may be necessary to lower exhaust to tighten 1/2" fasteners. (2) Seal all holes drilled in vehicle
to prevent entry of exhaust fumes into trunk.
11) Torque 1/2" fastners to 110 lb.-ft., 3/8" U-Bolt fasteners to 44 lb.-ft., other 3/8" fastners to 45 lb.-ft., M8 fastners to 13 lb.-ft. Reinstall
carpeting and spare tire cover in trunk.
93-97 DODGE INTREPID, 93-97 CHRYSLER CONCORDE,
94-97 CHRYSLER LHS, 94-96 CHRYSLER NEW YORKER, 93-97 EAGLE VISION
Used to replace existing
end cap bolt to allow clearence
for bolt in reinforcement plate
*New Yorker & LHS have a
frame extension. Hitch is
not to be installed in that area .
1
5
9
2
3
8
4
U-BOLT INSTALLATION
Drill holes in frame rail
as specified, using hitch
as a template.
Attach to frame
rail end cap
6
7
10
11
DESIGNED FOR USE WITH
BALLMOUNT #D221 / 45521