Installation Manual

ManualsBrandsCURT ManualsAutomotiveCURT 13066 Black 2" Class 3 Trailer Hitch Receiver for 2010-2015 Hyundai Tucson, 2011-2015 Kia Sportage

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND

CURT Manufacturing Inc. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing Inc. may repair or replace

the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement

of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.

For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com

MAKE: STYLE:

MIN.

WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY

WEIGHT CARRYING:

INSTALLATION TIPS: INSTALLATION TIME:

INSTALLATION REQUIRES:

VEHICLE PHOTO:

HITCH ILLUSTRATION:

REPRESENTATIVE PHOTO

MAKE SURE YOUR HITCH MATCHES

LEVEL OF DIFFICULTY:

EASY

MODERATE

HARD

THE INSTALL TIME LISTED IS FOR PROFESSIONAL

INSTALLERS. IF YOU ARE HESITANT TO UNDERTAKE

THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED

CURT INSTALLER FOR ADDITIONAL ASSISTANCE.

1. BEFORE YOU BEGIN INSTALLATION, READ ALL

INSTRUCTIONS THOROUGHLY.

2. TO EASE INSTALLATION, 2 PEOPLE MAY BE

REQUIRED.

3. USING PROPER TOOLS WILL GREATLY IMPROVE

THE QUALITY OF THE INSTALL AND REDUCE THE

TIME REQUIRED.

4. NEED HELP OR HAVE SOME QUESTIONS?

CALL TECHNICAL SUPPORT AT 800.798.0813

Safety glasses should be

worn at all times while

installing this product

YEARS: SEE APPL.

HYUNDAI / KIA

MODEL:

2010 TUCSON / 2011 SPORTAGE (EXCLUDING SX)

CROSSOVER

3,500

350

TRAILER WEIGHT:

TONGUE WEIGHT:

13066 INSTALLATION INSTRUCTIONS

LBS.

3/25/2011

WARNING:

WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER

(WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT

WWW.CURTMFG.COM FOR FURTHER INFORMATION.

- NO DRILLING REQUIRED

TORQUE

WRENCH

RATCHET

WIRE PIPE

BRUSH

SOCKET

17mm

SOCKET

EXTENSION

- MAY REQUIRE WELDNUT

CLEANING

Summary of content (4 pages)

PAGE 1
3066 MAKE: HYUNDAI / KIA YEARS: SEE APPL. Safety glasses should be worn at all times while installing this product . INSTALLATION INSTRUCTIONS MODEL: 2010 TUCSON / 2011 SPORTAGE (EXCLUDING SX) STYLE: CROSSOVER WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY WEIGHT CARRYING: INSTALLATION TIME: TRAILER WEIGHT: TONGUE WEIGHT: 15 MIN. THE INSTALL TIME LISTED IS FOR PROFESSIONAL INSTALLERS.
PAGE 2
INSTALLATION WALKTHROUGH: Parts List PART NUMBER 1. Locate weldnuts in frame rails. ITEM QTY 1 4 M10 - 1.25 x 30 HEX BOLT 2 4 3/8" CONICAL TOOTHED WASHER DESCRIPTION TUCSON / SPORTAGE TUCSON SPORTAGE TUCON / SPORTAGE 2 2. Raise hitch into position aligning holes in side plates with weldnuts and secure using M10-1.25 x 30mm bolts and 3/8" conical toothed washers. Note: For ease of installation, raise passenger side first then driver side. 1 For more information log onto www.curtmfg.
PAGE 3
INSTALLATION WALKTHROUGH: 3. Torque all M10 fasteners to 37 ft-lbs. INSTALLATION IS NOW COMPLETE For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.
PAGE 4
13066 HYUNDAI TUCSON / KIA SPORTAGE EXCLUDING SX 3/25/2011 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 3,500 LBS. TRAILER WEIGHT & 350 LBS. TONGUE WEIGHT. ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.