Installation Manual

ManualsBrandsCURT ManualsAutomotiveCURT 13079 Black 2" Class 3 Trailer Hitch Receiver for 2011-2019 Outlander, 2011-2018 Mitsubishi RVR

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND

CURT Manufacturing Inc. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing Inc. may repair or replace

the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement

of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.

For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com

MAKE: STYLE:

MIN.

WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY

WEIGHT CARRYING:

INSTALLATION TIPS: INSTALLATION TIME:

INSTALLATION REQUIRES:

VEHICLE PHOTO:

HITCH ILLUSTRATION:

REPRESENTATIVE PHOTO

MAKE SURE YOUR HITCH MATCHES

LEVEL OF DIFFICULTY:

EASY

MODERATE

HARD

THE INSTALL TIME LISTED IS FOR PROFESSIONAL

INSTALLERS. IF YOU ARE HESITANT TO UNDERTAKE

THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED

CURT INSTALLER FOR ADDITIONAL ASSISTANCE.

1. BEFORE YOU BEGIN INSTALLATION, READ ALL

INSTRUCTIONS THOROUGHLY.

2. TO EASE INSTALLATION, 2 PEOPLE MAY BE

REQUIRED.

3. USING PROPER TOOLS WILL GREATLY IMPROVE

THE QUALITY OF THE INSTALL AND REDUCE THE

TIME REQUIRED.

4. NEED HELP OR HAVE SOME QUESTIONS?

CALL TECHNICAL SUPPORT AT 800.798.0813

Safety glasses should be

worn at all times while

installing this product

YEARS:

2011 MITSUBISHI MODEL: OUTLANDER SPORT CROSSOVER

3,500

350

TRAILER WEIGHT:

TONGUE WEIGHT:

13079 INSTALLATION INSTRUCTIONS

LBS.

3/07/2011

WARNING:

WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER

(WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT

WWW.CURTMFG.COM FOR FURTHER INFORMATION.

TORQUE

WRENCH

SOCKET

EXTENSION

RATCHET

SOCKET

14mm

17mm

3/4"

PART REMOVAL

- NO DRILLING REQUIRED

- TOW LOOP REMOVAL

- MAY NEED WELDNUT

CLEANING

Summary of content (4 pages)

PAGE 1
3079 YEARS: 2011 Safety glasses should be worn at all times while installing this product . INSTALLATION INSTRUCTIONS MAKE: MITSUBISHI MODEL: OUTLANDER SPORT STYLE: CROSSOVER WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY WEIGHT CARRYING: INSTALLATION TIME: TRAILER WEIGHT: TONGUE WEIGHT: 15 MIN. THE INSTALL TIME LISTED IS FOR PROFESSIONAL INSTALLERS.
PAGE 2
INSTALLATION WALKTHROUGH: 1. Remove (3) bolts and tow loop from the passenger side frame rail. Return bolts and tow loop to owner Parts List ITEM QTY PART NUMBER DESCRIPTION 1 2 M10 - 1.25 x 25 HEX BOLT 2 2 3/8" CONICAL TOOTHED WASHER 3 4 HFN 1213 HEX FLANGE NUT 4 4 1/2-13 x 4 1/2 CARRIAGE BOLT 5 2 CM-13079-SP .250" SPACER PLATE 4 5 3 2 1 2. Insert 1/2-13 x 4 1/2" carriage bolts and CM-12048-SP spacers through the existing holes in the side of the frame rails.
PAGE 3
INSTALLATION WALKTHROUGH: 3. Raise the hitch into position and slide the bolts in the side of the frame rails through the holes in the hitch. Loosely secure hitch with 1/2" hex flange nuts. Note: The carriage bolts should sit flat on the spacers. Note: For ease of installation raise the driver side into position first, then raise the passenger side 5. Torque all 10mm hardware to 40 ft-lbs. Torque all 1/2" hardware to 75 ft-lbs. 4.
PAGE 4
13079 MITSUBISHI OUTLANDER SPORT 3/07/2011 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 3,500 LBS. TRAILER WEIGHT & 350 LBS. TONGUE WEIGHT. ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.