Installation Guide

ManualsBrandsCURT ManualsOtherClass 3 Trailer Hitch for Mitsubishi Outlander

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND

CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC. may repair or replace

the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement

of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.

For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com

MAKE: STYLE:

WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY

WEIGHT CARRYING:

INSTALLATION TIPS:

INSTALLATION REQUIRES:

VEHICLE PHOTO:

HITCH ILLUSTRATION:

REPRESENTATIVE PHOTO

MAKE SURE YOUR HITCH MATCHES

LEVEL OF DIFFICULTY:

MODERATE

EASY MODERATE CHALLENGING

1. BEFORE YOU BEGIN INSTALLATION, READ ALL

INSTRUCTIONS THOROUGHLY.

2. TO EASE INSTALLATION, 2 PEOPLE MAY BE

REQUIRED.

3. USING PROPER TOOLS WILL GREATLY IMPROVE

THE QUALITY OF THE INSTALL AND REDUCE THE

TIME REQUIRED.

4. NEED HELP OR HAVE SOME QUESTIONS?

CALL TECHNICAL SUPPORT AT 877.287.8634

Safety glasses should be

worn at all times while

installing this product

YEARS:

2014-CURRENT MITSUBISHI MODEL: OUTLANDER SUV

4,000

600

TRAILER WEIGHT:

TONGUE WEIGHT:

13163 INSTALLATION INSTRUCTIONS

LBS.

7/29/2019

WEIGHT DISTRIBUTION:

TRAILER WEIGHT:

TONGUE WEIGHT:

4,000

600

LBS.

MIN.

PRO INSTALL TIME:

NOVICE INSTALL TIME:

IF YOU ARE HESITANT TO UNDERTAKE

THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED

CURT INSTALLER FOR ADDITIONAL ASSISTANCE.

PART REMOVAL

- NO DRILLING

- FISHWIRE HARDWARE

- REMOVE TOW LOOP

- LOWER EXHAUST

- CLEAN WELDNUTS

RATCHET

TORQUE

WRENCH

SAFETY

GLASSES

SOCKET

12mm

14mm

17mm

3/4"

SOCKET

EXTENSION

SCREW

DRIVER

Summary of content (5 pages)

PAGE 1
3163 YEARS: 2014-CURRENT Safety glasses should be worn at all times while installing this product . INSTALLATION INSTRUCTIONS MAKE: MITSUBISHI MODEL: OUTLANDER STYLE: SUV WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY WEIGHT CARRYING: PRO INSTALL TIME: NOVICE INSTALL TIME: TRAILER WEIGHT: TONGUE WEIGHT: 30 MIN. 60 MIN. IF YOU ARE HESITANT TO UNDERTAKE THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
PAGE 2
INSTALLATION WALKTHROUGH: 1. Remove (3) bolts and tow loop from the driver side frame rail. Return bolts and tow loop to owner. Parts List ITEM QTY PART NUMBER DESCRIPTION 1 2 10-10282 BOLT, CAR,7/16-14 UNC,1-1/2,GRD8,YZ 2 4 10-10297 BOLT, CAR,1/2-13 UNC,4-1/2,GRD8,YZ 3 2 10-10298 HHCS,M10x1.25,35,CL10.9,YZ 4 4 20-00062 NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ 5 2 20-00103 NUT, SER-FLANGE,7/16-14 UNC,GRD8,YZ 6 2 30-00163 WASHER, S-CON,7/16,YZ 7 2 CM-SP2 .250 x .88 x 2.
PAGE 3
INSTALLATION WALKTHROUGH: 3. Raise the hitch into position and align the bottom tabs of the hitch with the center weldnuts in the frame rails. Loosely secure the hitch to the bottom of the frame rails with M10 hex bolts and 7/16" conical toothed washers. Note: On the end of the passenger side frame rail you may need to back out the inner bumper bolt to allow the hitch to be fully raised. If weldnuts do not exist fishwire 7/16" carriage bolts and spacers into the frame rails as shown. 5.
PAGE 4
13163 MITSUBISHI OUTLANDER 7/29/2019 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 4,000 LBS. TRAILER WEIGHT & 600 LBS. TONGUE WEIGHT. GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: 4,000 LBS. TRAILER WEIGHT & 600 LBS. TONGUE WEIGHT ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.
PAGE 5
13163 MITSUBISHI OUTLANDER GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 4,000 LBS. TRAILER WEIGHT & 600 LBS. TONGUE WEIGHT. GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: 4,000 LBS. TRAILER WEIGHT & 600 LBS. TONGUE WEIGHT ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634 FRAME RAIL REAR FASCIA HITCH SHOWN IN PROPER POSITION INSTALLATION STEPS 1.