Installation Guide

1/4" SPACER PLATE
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
1/2" FISHWIRE1_2 FISHWIRE11
.250 x 1.00 x 2.50" SQUARE HOLE SPACERCM-SP1022
NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ
20-0006283
HHCS,1/2-13 UNC,4,GRD8,YZ
10-1040764
WASHER,FLAT,1/2,YZ
30-0013365
BOLT,CAR,1/2-13 UNC,1-1/2,GRD8,YZ
10-1028726
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
6,000 600
10,000 1,000
03-06 DODGE & FREIGHTLINER SPRINTER VAN
8/6/2020
13250
90
40
45
HITCH WEIGHT:
LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
75886
1) Remove (2) existing bumper bolts from each side of the frame.(For step bumper models only.)
2) Remove undercoating from mounting surfaces as needed.
3) For step bumper models, break off corner of 1/4" spacer plates as shown. Position spacer plates on the inside of frame
rails. Raise hitch into position, using existing frame holes, install the 1/2" x 4" hex bolts, flatwashers, and flange nuts.
(Note: Do not break off spacer corner for non-step bumper models.)
4) Reinstall the bumper bracket fasteners removed in step 1.
5) Using hitch as a template, drill (2) 9/16" holes through frame as shown. Enlarge existing holes in bottom of
frame rails to 1 1/8".
6) Fishwire 1/2" carriage bolts and spacers through enlarged holes and secure with flange nuts.
7) Torque all 1/2" fasteners to 110 lb-ft and all M12 fasteners to 79 lb-ft (bumper bracket fasteners).
FRAME RAIL
FRAME RAIL
DRILLED HOLE
DRILLED HOLE
ENLARGED HOLE
(BOTH FRAME RAILS)
2
3
3
5
4
EXISTING
BUMPER
BOLT
EXISTING
FASTENERS
EXISTING
BUMPER
BOLT
EXISTING
FASTENERS
BREAK OFF CORNER ON
STEP BUMPER MODELS
-DRILLING REQUIRED
-BUMPER BRACKET
MODIFICATION REQUIRED
SPACERS MOUNT ON
INSIDE OF FRAME RAILS
14
6
- WILL NOT FIT 140" DUAL WHEEL SPRINTER MODEL
- 118" WHEEL BASE VEHICLES NEED TO HAVE SPARE RELOCATED AND EXHAUST HANGER MODIFIED.
- ALL 158" WHEEL BASE VEHICLES MUST HAVE STEP BUMPER SUPPORT BRACE REMOVED FROM THE
PASSENGER SIDE STEP BUMPER BRACKET.
WILL NOT FIT 140" DUAL WHEEL SPRINTER MODEL