Installation Guide

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY. ***
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM & FOR HELPFUL TOWING TIPS LOG ONTO WWW.HITCHINFO.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
6000 900
8000 900
TOYOTA TACOMA
5/1/2020
13264
40
34
20
HITCH WEIGHT:
LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
Scan
for more
information
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
1/2" x 30" FISHWIRE1_2 x 30 FISHWIRE21
HHCS,M12x1.25,40CL10.9,YZ
10-1027742
WASHER,S-CON,1/2,YZ
30-0014943
NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ
20-0006224
BOLT,CAR,1/2-13 UNC,1-3/4,GRD8,YZ
10-1027225
.250 x 1.25 x 3.00" SQUARE HOLE SPACERCM-SP1926
2
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
-NO DRILLING REQUIRED
-FISHWIRE HARDWARE
-CLEAN WELDNUTS
1. Fishwire (2) 1/2" carriage bolts and (2) CM-SP19 spacers through ends of bumper beam and out mounting
holes as shown. (See BUMPER BEAM FISHWIRE DIAGRAM)
2. Raise hitch into position between bumper mount plates and align slots in hitch with existing vehicle weldnuts in the
frame rails.
Install (4) M12-1.25 hex bolts and (4) 1/2" conical toothed washers into existing weldnuts, as shown.
3. Install (2) 1/2"-13 hex flange nuts on to carriage bolts.
4. Torque M12 fasteners to 86 lb-ft and 1/2" fasteners to 110 lb-ft.
BUMPER BEAM
5
4
1
6
3
TOOLS REQUIRED
RATCHET
TORQUE WRENCH
19mm SOCKET
3/4" SOCKET
10" SOCKET EXTENSION
BUMPER MOUNT PLATE
(BOTH SIDES)
EXISTING HOLES
BUMPER BEAM FISHWIRE DIAGRAM
BUMPER BEAM
MOUNTING HOLE
1. PUSH SPACER UP
2. PULL BOLT PARTIALLY
THROUGH SPACER
5
6
1
3. ROTATE BOLT AND SPACER
THROUGH MOUNTING HOLE

Summary of content (5 pages)