Installation Guide

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
5,000 500
60
30
ADJUSTABLE RV HITCH
8/13/2020
13704
65
Scan
for more
information
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ20-0006241
1/2" x 30" FISHWIRE1_2 x 30 FISHWIRE12
WASHER,FLAT,5/8,YZ
30-0013143
NUT,SER-FLANGE,5/8-11 UNC,GRD8,YZ
20-0010544
.250 x 1.50 x 2.00" SQUARE HOLE SPACERCM-SP1
45
HHCS,5/8-11 UNC,1-1/2,GRD8
10-1003846
BOLT,CAR,1/2-13 UNC,1-1/2,GRD8,YZ10-102874
7
- DRILLING REQUIRED
- FISHWIRE HARDWARE
- FRAME WIDTH: 22" TO 68.5"
1. Slide the left and right frame brackets onto the main body tube as shown.
2.
Position and clamp side brackets to the bottom of frame so the receiver tube with the ballmount is centered on vehicle. Be sure to
provide adequate coupler clearance.
3. Using side brackets as a template, drill two holes into frame using a 9/16 drill bit each side.
4.
Install 1/2" carriage bolts and spacers through drilled holes in frame and side brackets. If access holes are not present, bolts and
spacers may need to be fishwired into frame and/or bumper may need to be loosened for bolt and spacer installation. Loosely
install 1/2" flange nuts and remove clamps.
5. Center the main body on vehicle and clamp at both ends to prevent movement while drilling. Drill 11/16 diameter holes through
walls of cross tube using the two holes perside (total of four) in the side plate bracket tubes as templates. Install 5/8" hex bolts
and flat washer into holes. From inside main body tube, place flange nut onto 5/8 hex bolt and remove clamps.
6. Main body tube may be trimmed flush with outside of side plate bracket. (Note: If trimmed flush, coat bare metal with paint to
prevent corrosion.)
7. Torque 1/2" hardware to 110 lb-ft, and 5/8" hardware to 210 lb-ft.
6
3
4
7
5
1
2
TOOLS REQUIRED
RATCHET
3/4" SOCKET
11/16" SOCKET
11/16" WRENCH
DRILL
9/16" DRILL BIT
11/16" DRILL BIT
TORQUE WRENCH

Summary of content (1 pages)