Owners manual

ManualsBrandsCurt ManualsAutomotiveCURT 15510 Class V Multi-Fit Receiver Hitch

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT

***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***

HITCH WEIGHT: LBS.

INSTALL TIME: MINUTES

INSTALL NOTES:

INSTALLATION STEPS

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS

ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of

this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or

consequential loss or damage.

15,000 1,500

16,000 1,600

6/14/2012

15510

Parts List

DESCRIPTIONPART NUMBERQTYITEM

.250 x 1.50 x 3.00" SQUARE HOLE SPACERCM-SP421

HEX FLANGE NUTHFN 121362

CARRIAGE BOLT1/2-13 x 1 3/463

.250 x 1.50 x 2.00" SQUARE HOLE SPACERCM-SP164

CARRIAGE BOLT7/16-14 x 1 1/48

HEX FLANGE NUT7/16-1486

DRIVER SIDE FRAME RAIL

PASSENGER SIDE

FRAME RAIL

RECEIVER TUBE

ASSEMBLY

1. Bolt receiver tube assembly to driver and passenger side plates with 7/16" carriage bolts and hex flange nuts.

Side plate flanges should point outwards for 37 1/2" frames and inwards for 34" frames.

2. Loosen spare tire bracket to allow room for positioning the hitch. Position hitch so that the rivet head in the

frame rails are located just forward of the rear most side plate flange.

3. Using hitch as a template drill (6) 1/2" holes through frame rails

4. Slide the CM-SP4 spacer in between the hitch side plate and frame rail as shown.

5. Install 1/2" carriage bolts, CM-SP1 spacers and hex flange nuts as shown.

6. Retighten spare tire bracket. Torque 1/2" hardware to 110 lb-ft and 7/16" to 70 lb-ft.

1967-1999 FORD PICKUP, FULL SIZE, OLD BODY STYLE

1999 FORD F-450 CAB & CHASSIS, 2WD ONLY

- DRILLING REQUIRED

SIDE PLATE

LOCATE RIVET HEAD

FORWARD OF THIS

FLANGE BOTH SIDES

SIDE PLATE FLANGES

POINT OUTWARDS FOR 37 1/2" FRAMES

POINT INWARDS FOR 34" FRAMES

(SHOWN POINTING OUTWARDS)

Summary of content (3 pages)

PAGE 1
967-1999 FORD PICKUP, FULL SIZE, OLD BODY STYLE 1999 FORD F-450 CAB & CHASSIS, 2WD ONLY 15510 6/14/2012 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 15,000 LBS. TRAILER WEIGHT & 1,500 LBS. TONGUE WEIGHT. GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: 16,000 LBS. TRAILER WEIGHT & 1,600 LBS. TONGUE WEIGHT ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** Parts List ITEM QTY PART NUMBER DESCRIPTION 1 2 CM-SP4 .250 x 1.50 x 3.
PAGE 2
DODGE PICKUP, FULL SIZE 15510 6/14/2012 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 15,000 LBS. TRAILER WEIGHT & 1,500 LBS. TONGUE WEIGHT. GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: 16,000 LBS. TRAILER WEIGHT & 1,600 LBS. TONGUE WEIGHT ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** Parts List ITEM 1 QTY 2 PART NUMBER CM-SP4 DESCRIPTION .250 x 1.50 x 3.
PAGE 3
1962-1987 CHEVROLET/GMC PICKUP, FULL SIZE, NOT SHORT BOX 1988-1999 CHEVROLET/GMC LONG AND SHORT CAB & CHASSIS, WITH 34" FRAME 15510 6/14/2012 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 15,000 LBS. TRAILER WEIGHT & 1,500 LBS. TONGUE WEIGHT. GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: 16,000 LBS. TRAILER WEIGHT & 1,600 LBS. TONGUE WEIGHT ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.