Owners manual

ManualsBrandsCurt ManualsAutomotiveCURT 16300 Fifth Wheel Custom Bracket Kit Fits 04-11 F-150

Parts List

DESCRIPTION

PART NUMBER

QTY

ITEM

FISHWIRE TOOL1/2"11

.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP682

HEX NUT1/2-13183

LOCK WASHER1/2"184

.313" x 1.00 x 2.00" U-SHAPE SPACERCM-SP13610

FW, 12, ZPFW12106

CARRIAGE BOLT1/2 - 13 x 2"107

FLAT WASHER SPECIAL

M1228

FLAT WASHER SPECIAL

1/2"29

CARRIAGE BOLT1/2-13 x 1 1/2810

.375" PASSENGER SIDE PLATECM-16300-PS211

.375" DRIVER SIDE PLATECM-16300-DS212

Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of

this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or

consequential loss or damage.

16300 FORD '04 AND NEWER F-150

3/19/2013

Fig. 1

BRACKET INSTALLATION

HARDWARE

RAIL INSTALLATION

HARDWARE

Summary of content (4 pages)

PAGE 1
6300 FORD '04 AND NEWER F-150 3/19/2013 Parts List ITEM 1 QTY 1 PART NUMBER 1/2" DESCRIPTION FISHWIRE TOOL 2 8 CM-SP6 .250 x 1.00 x 3.00" SQUARE HOLE SPACER 3 18 1/2-13 HEX NUT 4 18 1/2" LOCK WASHER 5 10 CM-SP136 .313" x 1.00 x 2.00" U-SHAPE SPACER 6 10 FW12 FW, 12, ZP 7 10 1/2 - 13 x 2" CARRIAGE BOLT 8 2 M12 FLAT WASHER SPECIAL 9 2 1/2" FLAT WASHER SPECIAL 10 8 1/2-13 x 1 1/2 CARRIAGE BOLT 11 2 CM-16300-PS .375" PASSENGER SIDE PLATE 12 2 CM-16300-DS .
PAGE 2
GENERAL INST RUCTIONS FOR M OUNTING RAIL IN ST ALLAT ION TO O LS 3/16” drill 3/4” Socket & Open End W rench 17/32” drill 100 lb-ft T orque W rench 1” drill (Some Dodge application only) “C” Clamps 1. T he following instructions should be used to mount the 5 th wheel. Care and attention to detail will ensure a quality installation. Check parts against parts list to become familiar with parts in kit. (See Fig. 1) 2.
PAGE 3
10. Drill two holes in frame for each bracket. Select the holes which will give the greatest spread between bolts. Install eight 1/2”-13x1-1/2” carriage bolts and spacers. Note: On vehicles with heavy duty suspensions, check for interference with bolts where brackets are mounted to frame. If interference with suspension spring results, cut bolt flush to nut outboard of frame or use weld option. WARNING: DO NOT lubricate threads. It may cause bolt failure. CAUTION: Check for obstructions before drilling.
PAGE 4
FORD '04 AND NEWER F-150 CAUTION! READ INSTRUCTIONS OF RAIL SYSTEM BEFORE STARTING INSTALLATION. FAILURE TO DO SO COULD RESULT IN SIGNIFICANT VEHICLE DAMAGE! IMPORTANT NOTES FOR THIS INSTALLATION: 1. Do not drill through both walls of frame. Drill only through wall of frame to which bracket is mounted. 4. When brackets are in place one of the front 2 holes should line up with a hole in the frame. A hole will need to be drilled in the frame at the rearward bracket hole. 5.