Installation Guide

ManualsBrandsCURT ManualsAutomotiveCURT 17500 TruTrack Black Trunnion Bar Weight Distribution Hitch with Integrated Sway Control (10,000 lbs. GTW, 2" Shank)

CURTMFG.COM

•

PRODUCT SUPPORT: 877.287.8634

•

17500-INS-RD

•

12/08/2021

•

ECN8701

•

PAGE 1

Product Registration and Warranty

CURT stands behind our products with

industry-leading warranties. To get copies

of the product warranties, register your

purchase or provide feedback, visit:

warranty.curtgroup.com/surveys

Max Capacity Without Spring Bars

Gross trailer weight (GTW) 10,000 lbs.

Tongue weight (TW) 1,000 lbs.

When spring bars are not used, the weight

rating is dependent upon the trailer ball

manufacturer's weight ratings. Do not exceed

the maximum weight rating of the trailer ball.

Max Capacity With Spring Bars

Gross trailer weight 8,000 - 10,000 lbs.

Tongue weight 800 - 1,000 lbs.

The tongue weight rating of the spring bars

represents the capacity of a pair of bars, not

an individual bar. Always use a pair of spring

bars and be sure they are rated the same.

INSTALLATION MANUAL

17500

Tools Required

Ratchet Socket set

Torque wrench Tape measure

Level of Difficulty

Moderate

Installation difficulty levels are based on time

and effort involved and may vary depending on

the installer level of expertise, condition of the

vehicle and proper tools and equipment.

NOTICE

Visit www.curtmfg.com for a full-color copy of this

instruction manual, as well as helpful videos, guides and much more!

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

Some states require a clear view of license plates.

Remove trailer ball when not in use if it restricts view.

This product complies with regulation V-5, C.S.A. Standard D-264 and safety

requirements for connecting devices and towing systems of the State of New York.

Periodic inspection of your product should be performed

to ensure all hardware and / or components remain secure.

To help prevent damage to the product or vehicle, refer to the specified

torque specifications when securing hardware during the installation process.

WARNING

Never exceed the vehicle manufacturer's recommended towing capacity.

The loaded ball height should never be greater than the uncoupled ball height. Front wheel overload

and loss of rear wheel traction can result and can lead to unstable handling. It can reduce

braking ability and create a tendency to jackknife when turning and braking at the same time.

If the loaded trailer ball height is greater than the uncoupled height, reduce take-up

on the spring bar, remeasure and adjust until the proper height is obtained.

Product Photo

Maintenance

Keep the socket-mounted ends of the spring bars and the lock pins

in the head assembly free from dirt and well lubricated. Excessive wear

in this area may indicate an overload or inadequate lubrication.

Keep the head assembly exterior clean. Do not allow dirt

or stones to lodge between the spring bars and the head.

Keep hitch parts painted to prevent rust and maintain good appearance. Do not paint over labels.

Keep lift brackets clean and lubricated to ensure ease of operation.

Parts List

Item Qty Description

1 1 Hitch head

2 1 Adjustable shank

3 2 Spring trunnion bar

4 2 Spring bar support bracket

5 1 Snap-up handle

6 2 Head tilt spacer

7 1 Hex bolt, 3/4"-10 x 5"

8 2 Nylock nut, 3/4"-10

9 1 Hex bolt, 3/4"-10 x 4"

10 2 Wire lock lynch pin

11 1 Hitch pin & clip, 5/8"

Summary of content (6 pages)

PAGE 1
INSTALLATION MANUAL Level of Difficulty 17500 WARNING Moderate Installation difficulty levels are based on time and effort involved and may vary depending on the installer level of expertise, condition of the vehicle and proper tools and equipment. Never exceed the vehicle manufacturer's recommended towing capacity. The loaded ball height should never be greater than the uncoupled ball height. Front wheel overload and loss of rear wheel traction can result and can lead to unstable handling.
PAGE 2
SPRING BAR WIDTH ADJUSTMENT Step 1 - Determine your spring bar width setting Step 3 - Install the sockets back into the head TruTrack™ Once the cam block has been adjusted, lightly coat the balls with grease and set into the ball sockets. Flip the socket upside down and position it so the balls are resting in the cam block recesses. is designed to work in two neutral spring bar settings to fit most A-frame trailers. The spring bars can easily be repositioned in the 30° or 70° position (+/-5°).
PAGE 3
ASSEMBLY & INSTALLATION Parts List Item 1 2 3 4 5 6 7 8 9 10 11 Qty 1 1 2 2 1 2 1 2 1 2 1 Description Hitch head Adjustable shank Spring trunnion bar Spring bar support bracket Snap-up handle Head tilt spacer Hex bolt, 3/4"-10 x 5" Nylock nut, 3/4"-10 Hex bolt, 3/4"-10 x 4" Wire lock lynch pin Hitch pin & clip, 5/8" 8 4 6 3 1 5 10 2 7 9 11 Step 1 - Measure the trailer coupler height Step 2 - Measure the towing vehicle Line up the tow vehicle and trailer on level pavement, in a straight position.
PAGE 4
Step 4 - Install the shank, hitch head and ball Step 8 - Install the spring bars Insert the adjustable shank (#2) into the receiver tube on the tow vehicle and secure with the provided hitch pin & clip (#11). Note: To obtain the proper ball height on high-ground-clearance vehicles, the shank may be inverted as shown below. If the shank is used in the inverted position, check for adequate ground clearance. Secure the two spring bars (#3) with the wire lock lynch pins (#10).
PAGE 5
Step 12 Step 15 Slide the L-support in between the two captive support brackets as shown. Set the bracket height closest to the spring bar position set with the jack in Step 9. Install the second carriage bolt in the first hole directly below the trailer A-frame. Pry the spring bar onto the L-bracket by rotating the lift bar to vertical. With the spring bar supported by the L-bracket, remove the lift handle. Secure the spring bar by installing the retainer clip and cotter pin.
PAGE 6
Before You Tow Final Installed Image - Representative Photo (#17501 shown) Check all connections listed below prior to towing: - Hitch pin & clip (securing shank to receiver) Head to shank fasteners Trailer ball nut Coupler latch Spring bar support brackets Safety chains Lights and turn signals Braking system (including breakaway switch) Apply grease to the locations shown below prior to each use to ensure quiet and trouble-free operation.