Installation Guide

Parts List
ITEM QTY PART NUMBER DESCRIPTION
1 4 HFN 1213 HEX FLANGE NUT
2 2 CM-SP16 .250 x 1.50 x 2.00" ROUND HOLE SPACER
3 4 1/2-13 x 1 1/4 HEX BOLT
4 2 1/2" CONICAL TOOTHED WASHER
5 1 1_2 FISHWIRE 1/2" FISHWIRE
6 2 1/2-13 HANDLE NUT
7 2 CM-SP3 .250 x 1.25 x 2.00" SQUARE HOLE SPACER
8 2 1/2-13 x 1 1/2 CARRIAGE BOLT
UNDERCARRIAGE DEFLECTOR
NOTCH PATTERN
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
GROSS LOAD CAPACITY WHEN USED AS A STRAIGHT LINE PULL: 9,000 LBS. MAX. LINE PULL.
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY. ***
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
3,500 350
JEEP WRANGLER UNLIMITED
11/6/2018
31432
90
20
45
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
Scan
for more
information
6
7
8
1
3
4
FRONT FRAME RAIL ASSM.
BOTTOM OF BUMPER
B
A
B
C
C
1) Remove undercarriage deflector from vehicle by removing six plastic screw fasteners.
(Tip: To remove fasteners squeeze pointed tip and unscrew using phillips screw driver.)
2) Raise hitch into position and align holes in frame with holes in hitch. NOTE: For additional access remove the
(2) plastic fasteners securing the plastic cover on the top of the bumper. If equipped with brake booster pump
remove the forward most bolt and rotate out of the way.
3) Fasten hitch to bottom of bumper using supplied hardware and hand tighten.
4) Fishwire 1/2" carriage bolts and spacers through bottom hole of frame rails and secure. Some models may
require hole enlargement on the driver side frame rail.
5) Install remaining hardware as shown.
6) Torque all 1/2" hardware to 110 lb-ft. Reinstall brake booster pump and plastic fasteners if removed in Step 2.
7) (Optional - if reinstalling undercarriage deflector on vehicle, notch as shown to allow clearance
for corresponding hitch components.)
- NO DRILLING REQUIRED
- DEFLECTOR TRIMMING OPTIONAL
- HOLE ENLARGEMENT MAY BE
REQUIRED
C
C
B
B
1
2
3
WILL NOT WORK WITH OPTIONAL BUMPERS
SOME MODELS MAY REQUIRE HOLE ENLARGEMENT
5
A