Installation Guide

ManualsBrandsCURT ManualsOtherCustom Wiring 4-Way Flat Output Select Hyundai Entourage Kia Sedona Seltos

56442-INS-RA

•

04/23/2020

•

PAGE 1

Wiring Location Guide*

for SUVs and Vans (S)

S1 Behind driver side taillight housing

S2 Behind passenger side taillight housing

S1 S2

* Representative vehicle shown

INSTALLATION MANUAL

Tools Required

Ratchet Flathead screwdriver

Socket, 10mm Utility knife

Socket extension Wire crimper

Electrical tape Wire stripper

Phillips screwdriver Panel removal tool

Wiring Location(s)

P1 and P2, S1 and S2

Level of Difﬁculty

Easy

Product Photo

Hardware Photo

WARNING

Do not exceed product rating or tow vehicle lamp load rating, whichever is lower.

The battery connection must be fuse-protected, 10-amp max. Exceeding

the product rating can cause loss of warranty, overheating and potential fire.

Product Registration and Warranty

CURT stands behind our products with industry-leading warranties. To get copies of the product

warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys

Maintenance

Periodic inspection of all wires and connections should be performed

to ensure there is no visible damage or loose connections.

Electrical Ratings

Signal circuits 3.0-amps per side

Tail / Running Circuits 6.0-amps total

Check vehicle owner's manual or contact

the vehicle manufacturer for more information.

Wiring Location Guide*

for Passenger Cars (P)

P1 Behind driver side taillight

housing, outside of trunk

P2 Behind passenger side taillight

housing, outside of trunk

P1 P2

* Representative vehicle shown

NOTICE

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

All steps must be followed to ensure the product will function properly. Once installed,

test for proper function by using a test light or connecting a properly wired trailer.

Summary of content (10 pages)

PAGE 1
INSTALLATION MANUAL WARNING Level of Difficulty Do not exceed product rating or tow vehicle lamp load rating, whichever is lower. The battery connection must be fuse-protected, 10-amp max. Exceeding the product rating can cause loss of warranty, overheating and potential fire. Easy Electrical Ratings Signal circuits Tail / Running Circuits 3.0-amps per side 6.0-amps total Product Photo Check vehicle owner's manual or contact the vehicle manufacturer for more information.
PAGE 2
Step 1A: Hyundai Entourage & Kia Sedona Locate the vehicle's battery and disconnect the negative battery terminal. Be sure to fasten this wire down and away from the battery while completing the insulation process. WARNING Do not to lay tools on the positive (+) battery terminal. This can cause a short in the system, sparks and / or electrical shocks. Step 2A: Hyundai Entourage & Kia Sedona Open the vehicle hatch.
PAGE 3
Step 2B: Hyundai Tucson Open the vehicle hatch. Using the trim removal tool to release a small tab in the taillight trim cover. Set the cover aside. Use a 10mm socket to remove the taillight fasteners securing the taillight in place. Step 3B: Hyundai Tucson Pull the taillight straight back. Separate the connectors from the taillight housing taking care not to damage the locking tabs. Set the taillight aside. Use the trim panel removal tool to remove the two push fasteners in the bumper cover.
PAGE 4
Step 5B: Hyundai Tucson From the driver side, attach the custom wiring end with yellow wire to the fishwire and pull the harness up between the body and the bumper cover. Note: You may need to flex the bumper cover to get the housings through the opening. Insert the custom wiring end with yellow wire between the separated connectors. Make sure the connectors are fully inserted with locking tabs in place.
PAGE 5
Step 1C: Hyundai Veloster Locate the vehicle's battery and disconnect the negative battery terminal. Be sure to fasten this wire down and away from the battery while completing the insulation process. WARNING Do not to lay tools on the positive (+) battery terminal. This can cause a short in the system, sparks and / or electrical shocks. Step 2C: Hyundai Veloster Open the vehicle trunk. Starting on the driver side, use a flathead screwdriver to open the access covers for the taillight mounting screws.
PAGE 6
Step 5C: Hyundai Veloster Attach the custom wiring end with the green wire and 4-flat to the fishwire and pull the harness down inside the bumper to the under body of the vehicle. From under the vehicle route over to the center of the vehicle. Secure any loose wires with the provided cable ties. Continue routing the wiring to the passenger side of the vehicle and up to the taillight. Insert the custom wiring end with green wire between the separated connectors.
PAGE 7
Step 1D: Kia Seltos Locate the vehicle's battery and disconnect the negative battery terminal. Be sure to fasten this wire down and away from the battery while completing the insulation process. WARNING Do not to lay tools on the positive (+) battery terminal. This can cause a short in the system, sparks and / or electrical shocks. Step 2D: Kia Seltos Open the vehicle hatch. Starting on the driver side, use a Philips screwdriver to remove the two screws securing the taillight.
PAGE 8
Step 4D: Kia Seltos Route the 4-flat along the backside of the bumper to the center of the vehicle and mount it close to the trailer hitch. Route the green wire along the backside of the bumper to the passenger side. Use a trim removal tool to remove the two push fasteners. This will allow you to locate the fishwire. Secure any loose wires with the provided cable ties. Locate a flat spot between the body of the vehicle and the bumper cover just below the taillight.
PAGE 9
Step 3E: Kia Soul Use a Philips screwdriver to remove the push fastener in the bumper cover. This allows for more room while fishwiring the custom wiring housing up to the taillight. Route the fishwire down between the body and bumper cover. From underneath of the vehicle locate the connector with the yellow wire. Pull the harness up to the taillight and insert the custom wiring end with yellow wire between the separated connectors. Make sure the connectors are fully inserted with locking tabs in place.
PAGE 10
POWERED CONVERTER LEAD INSTRUCTION SHEET FICHE DE CONSIGNES DU CONVERTISSEUR D'ALIMENTATION HOJA DE INSTRUCCIONES DEL CONDUCTOR DEL ADAPTADOR ALIMENTADO POR BATERÍA NOTICE AVIS / AVISO WARNING AVERTISSEMENT / ADVERTENCIA Illustrations are for reference only. Battery location may differ depending on the vehicle. To avoid personal injury or property damage, check for miscellaneous items that may be behind or under any surface before drilling. Les images ne sont fournies qu'à des fins de référence.