Owners manual

ManualsBrandsCurt ManualsAutomotiveCURT 60664 600 Series Install Kit Gooseneck Hitch Fits 04-19 Titan

Curt Manufacturing Inc., warrants this product to be free of defects in material or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

Curt Manufacturing Inc., may repair or replace the product, at their option,when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of

this product voids the warrant. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specificaly excludes liability for incidental or

consequential loss or damage.

60664

INSTALLATION STEPS

WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE.

ALL MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE

BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.

FRONT OF TRUCK

FIGURE 1

REAR OF TRUCK

FIGURE 2

BEFORE INSTALLING

An overhead lifting device, such as chain falls, engine hoist, or cable come-a-long, can be used to lift the center section of the

hitch in place. Lower a loop of rope or chain through the 4" hole in the truck bed floor and attach it to the round hitch receiver

tube in the center section. Use the lifting device to raise the center section until the round hitch receiver tube that protrudes

from the center section fits in the 4" hole in the truck bed floor. Maintaining upward pressure may facilitate fastening the cross-

member to the center section, especially if the truck bed floor has been distorted downward from heavy use. If you use an

overhead-lifting device, it should be disconnected before squaring the center section across the frame, installing the sideplates

and torquing fasteners.

1) A) Lower and remove spare tire.

B) Remove the heat shield under the bed floor by removing the six screws with a 10 MM wrench.

C) The fuel valve canister must be lowered during the installation to allow the handle and bolts to be installed. First remove

the 3 small bolts that hold the canister bracket to the truck using a 10 MM wrench. Next, using a small screwdriver re-

move the vent hose from the bed cross member. Then slide the canister toward the center of the truck far enough to

allow the end toward the frame to be pulled downward. Then slide the canister back toward the frame to allow the com-

plete canister to drop down about 4-5 inches this will be enough room to complete the installation. After installation is

complete, bolt the canister back to the brackets, and cable tie the vent hose to the rear cross arm.

D) The inner fender guards toward the front of both rear fender wells will need to be removed to allow the installation of the

hitch side plates. This is done by removing two screws and sliding the guard toward the tire. These guards will be re-

attached after full hitch installation.

2) Mark the location for the hole in the truck bed. Measure from the tail gate end of the truck bed, by hooking a tape measure

over the back of the truck box and marking the correct location.(NOTE: DO NOT MEASURE FROM EDGE OF TAILGATE)

Next, mark the center between the wheel wells. This marks the center point for the 4" hole. This hole location is critical for

the correct installation of this hitch. Measure, mark, and saw carefully. This location will put the ball 4"-6" in front of the axle.

Short Bed Installation 46 1/2"

Long Bed Installation 46 1/2"

04-CURRENT NISSAN TITAN

LONG AND SHORT BED

PAGE 1

12/28/2012

**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!**

22.25

0.5

BED CROSS MEMBER

FLANGE

TOP OF

FRAME

SHOWN WITH C-620

INSTALLED

(NOT INCLUDED WITH SUBKIT)

FRONT CROSS ARM

DRIVER SIDE PLATE

PASSENGER SIDE PLATE

INSERT INTO EXISTING HOLE

ON INSIDE OF TRUCK FRAME

REAR

CROSS ARM

1" BED FLOOR FLANGE IN

PASSENGER SIDE WHEEL WELL

10" CABLE TIE

WARNING!! ON TWO WHEEL DRIVE TRUCKS A CLEARANCE CHECK MUST BE PERFORMED WHEN TRUCK IS LOADED

AND UNLOADED TO VERIFY THE INVERTED BALL WILL NOT INTERFERE WITH THE TOP OF THE DIFFERENTIAL

Summary of content (3 pages)

PAGE 1
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 12/28/2012 04-CURRENT NISSAN TITAN LONG AND SHORT BED 60664 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 2
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 04-CURRENT NISSAN TITAN LONG AND SHORT BED 60664 NOTE: If truck has a plastic bed liner, you may drill through both, but it is more difficult to accurately locate the midpoint between the wheel wells, and to keep the bed liner from moving while cuttingthe hole. Make a 4" hole at this location using a 4" hole saw, or by making a 4" circle and cutting it out with a saber saw equipped with a metal cutting blade.
PAGE 3
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** CAB TO TRAILER CLEARANCE **REMOVAL OF REAR WINDOW ACCESSORIES MAY BE REQUIRED.** COUPLER OVERHANG TRAILER 4 in (W) 96 in COUPLER ***GENERALLY, TAPERED NOSE TRAILERS ADHERE TO THE FOLLOWING DESIGNS:*** 8 FT. WIDE TRAILERS TAPER TO 6 FT. AT THE COUPLER. 7 FT. WIDE TRAILERS TAPER TO 5 FT. AT THE COUPLER.