Owners manual

ManualsBrandsCurt ManualsAutomotiveCURT 60680 Double-Lock Gooseneck Hitch/Install Kit

Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of

this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or

consequential loss or damage.

CHEVY & GMC 2500 / 3500 SHORT AND LONG BED

10/7/2016

**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!**

60624 SUBKIT

PAGE 1 OF 4

WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL

MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE

BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB. ON TWO WHEEL DRIVE TRUCKS A CLEARANCE CHECK MUST BE PERFORMED

WHEN TRUCK IS LOADED AND UNLOADED TO VERIFY THE INVERTED BALL WILL NOT INTERFERE WITH THE TOP OF THE DIFFERENTIAL

SUBKIT WEIGHT:

LBS.

INSTALL TIME

PROFESSIONAL: MINUTES

NOVICE (DIY): MINUTES

INSTALL NOTES:

PERIODICALLY CHECK THIS GOOSENECK HITCH TO ENSURE THAT ALL FASTENERS

ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

Parts List

DESCRIPTION

PART NUMBER

QTY

ITEM

FRONT CROSS ARM60624-FCA1A

REAR CROSS ARM60624-RCA1

DRIVER SIDE PLATE60624-DS

PASSENGER SIDE PLATE60624-PS

Hardware

DESCRIPTION

PART NUMBER

QTY

ITEM

HEX BOLT1_2 - 13 x 1 1_2 HEX, GR861

CONICAL TOOTHED WASHER1/262

CARRIAGE BOLT1/2-13 x 1 1/2, GR843

.250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP121

HEX FLANGE NUTHFN 1213, GR8

CARRIAGE BOLT5/8-11 x 1 3_4, GR8

.250 x 1.25 x 2.50" SQUARE HOLE SPACERCM-SP9

HEX FLANGE NUT5/8-11, GR8

5/8" FISHWIRE5_8 FISHWIRE49

1/2" PUSHNUT BOLT RETAINER1/2 PNBR210

M16 - 2.00 x 35 HHCS GR8.8 YZM16 - 2.00 x 35 HHCS GR. 8.8411

HELICAL LOCK WASHER5_8 LOCK WASHER412

WASHER5_8 WASHER

- LOWER SPARE TIRE

- TRIM HEAT SHEILD

- NO MEASURING DRILL LOCATIONS

- NO DRILLING INTO FRAME

- NO LOWERING EXHAUST

ACCESS HOLE

(BOTH SIDES)

PASSENGER SIDE FRAME RAIL

DRIVER SIDE FRAME RAIL

DESIGNED FOR USE WITH

60611 CENTER SECTION

(NOT INCLUDED IN SUBKIT)

TOOLS REQUIRED

SAFETY GLASSES

EAR PROTECTION

ROTARY TOOL

CUT WHEEL (FOR SHEET METAL)

RATCHET

3" & 6" SOCKET EXTENSION

13mm, 24mm, 3/4" & 15/16" SOCKETS

3/4" END WRENCH

CRESCENT WRENCH

TORQUE WRENCH

Summary of content (7 pages)

PAGE 1
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 60624 SUBKIT CHEVY & GMC 2500 / 3500 SHORT AND LONG BED 10/7/2016 PAGE 1 OF 4 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 2
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 60624 SUBKIT CHEVY & GMC 2500 / 3500 SHORT AND LONG BED PAGE 2 OF 4 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 3
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 60624 SUBKIT CHEVY & GMC 2500 / 3500 SHORT AND LONG BED PAGE 3 OF 4 BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 4
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** CAB TO TRAILER CLEARANCE PAGE 4 OF 4 **REMOVAL OF REAR WINDOW ACCESSORIES MAY BE REQUIRED.** COUPLER OVERHANG TRAILER 4 in (W) 96 in COUPLER ***GENERALLY, TAPERED NOSE TRAILERS ADHERE TO THE FOLLOWING DESIGNS:*** 8 FT. WIDE TRAILERS TAPER TO 6 FT. AT THE COUPLER. 7 FT. WIDE TRAILERS TAPER TO 5 FT. AT THE COUPLER.
PAGE 5
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 60611 GOOSENECK HITCH 4/16/2014 PAGE 1 OF 3 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. SOME MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 6
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 60611 GOOSENECK HITCH PAGE 2 OF 3 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. SOME MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 7
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 60611 GOOSENECK HITCH PAGE 3 OF 3 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. SOME MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.