Installation Guide

ManualsBrandsCurt ManualsAutomotiveCURT 60700 Gooseneck Hitch

FIGURE 1

Parts List

DESCRIPTIONPART NUMBERQTYITEM

DRIVER SIDE PLATE60651-DS1A

PASSENGER SIDE PLATE60651-PS1B

DRIVER SIDE PLATE 260651-DS21C

PASSENGER SIDE PLATE 260651-PS21D

DRIVER SIDE FRONT WELDMENT60651-DSFWA1E

PASSENGER SIDE FRONT PLATE60651-PSF1F

DRIVER SIDE REAR PLATE60651-DSR1G

PASSENGER SIDE REAR PLATE60651-PSR1H

Hardware List

DESCRIPTIONPART NUMBERQTYITEM

HEX FLANGE NUT5/8-11161

HEX BOLT5_8 - 11 x 4 HEX42

WASHER5_8 WASHER

GRADE 8 HEX BOLT

9_16-12 x 1.584

CONICAL TOOTHED WASHER9/16" CONICAL WASHER

.313 x 1.50 x 3.00" 9/16" SQUARE HOLE SPACERCM-SP7486

CARRIAGE BOLT5/8-11 x 1 3_4, GR8127

U-BOLT SPRINGCM-C113-UBS48

FLAT WASHERM16 WASHER89

5/8" SQUARE U-BOLT60651-UB210

CENTER LOCK NUT5/8-18411

.300" U-SHAPED EDGINGCM-UE1112

BOLT RETAINER CLIP60651-BRC413

FORD SUPERDUTY GOOSENECK SUBKIT

6/14/2017

**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!**

60700 (60610 & 60651)

PAGE 1 OF 5

WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL

MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE

BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB. ON TWO WHEEL DRIVE TRUCKS A CLEARANCE CHECK MUST BE PERFORMED

WHEN TRUCK IS LOADED AND UNLOADED TO VERIFY THE INVERTED BALL WILL NOT INTERFERE WITH THE TOP OF THE DIFFERENTIAL

150

SUBKIT WEIGHT: LBS.

INSTALL TIME

PROFESSIONAL: MINUTES

NOVICE (DIY): MINUTES

INSTALL NOTES:

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS

ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

Scan

for more

information

CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.

If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,

with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to

repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.

60610 CENTER SECTION

- NO FRAME DRILLING REQUIRED

- NO MEASURING DRILL LOCATIONS

- NO LOWERING EXHAUST OR SPARE

REQUIRED

NOTCHED FOR FUEL

TANK CLEARANCE

CUTOUT FOR PASSENGER

SIDE SHOCK MOUNT

TOOLS REQUIRED

RATCHET

TORQUE WRENCH

18" OF SOCKET EXTENTIONS

13/16" AND 15/16" SOCKETS

DRILL

11/16" DRILL BIT

3 1/4" HOLE SAW

CUTTING FLUID

RUST INHIBITOR

EAR AND EYE PROTECTION

Summary of content (5 pages)

PAGE 1
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 60700 (60610 & 60651) FORD SUPERDUTY GOOSENECK SUBKIT 6/14/2017 PAGE 1 OF 5 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 2
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 60700 (60610 & 60651) FORD SUPERDUTY GOOSENECK SUBKIT PAGE 2 OF 5 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 3
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 60700 (60610 & 60651) FORD SUPERDUTY GOOSENECK SUBKIT PAGE 3 OF 5 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 4
CAB TO TRAILER CLEARANCE PAGE 4 OF 5 ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634 **REMOVAL OF REAR WINDOW ACCESSORIES MAY BE REQUIRED** COUPLER OVERHANG 96 in CAB OF TRUCK 4 in (W) (MEASURE) X 72 in TRAILER HITCH BALL COUPLER 36 in (Y) Y TR A IL ER **GENERALLY, TAPERED NOSE TRAILERS ADHERE TO THE FOLLOWING DESIGNS:** 8 FT. WIDE TRAILERS TAPER TO 6 FT. AT THE COUPLER 7 FT.
PAGE 5
IMPORTANT TOWING INFORMATION PAGE 5 OF 5 ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634 BEFORE TOWING THE FIRST TIME: - Verify adequate turning clearance between the truck cab / box corners and trailer(s). - Check truck box clearance. There should be a minimum clearance of 6" between the bottom of the trailer(s) overhang and the top of the box sides. - Verify all hardware is torqued to the proper specification.