TV2710 Colour Television OPERATION MANUAL Please read these instructions carefully Before operating this product
INTRODUCTION Thank you for purchasing our product. To ensure that you fully understand the capabilities of this television set, please read this entire manual carefully, and keep it handy for future reference. INSTALLATION • • • • • Locate the TV set in a room where direct light does not reflect on the screen. Total darkness or a reflection on the picture screen can cause eye strain. Soft and indirect lighting is recommended for comfortable viewing.
IMPORTANT SAFEGUARDS 1. READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated. 2. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. 3. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to. 4. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. 5. CLEANING Unplug this unit from the wall outlet before cleaning.
18. SERVICING Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. SAFETY CHECK Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition. 22. HEAT 19.
LOCATION OF CONTROLS Television Set 1. 2. 3. 4. 5. 6. 7. 8. Side A/V Inputs Speaker TV/AV Selector Menu Button Volume Down Button Volume Up Button Channel Down Button Channel Up Button 9. 10. 11. 12. 13. 14. 15. 16.
Connection to Other Devices This TV set can be connected to a VCR, DVD player, video camera, game system or any other A/V component. DVD Player Side Jacks Video/Audio equipment can be connected to AUDIO and VIDEO IN jacks located on the back or side panel of the TV set.
REMOTE CONTROL
USING THE REMOTE CONTROL Installing batteries Notes: Use only the size and type of batteries specified. Do not mix different types of batteries together or old batteries with fresh ones. Remove the batteries when remote control will not be used for a long period of time. Avoid direct sunlight, incandescent lamp, fluorescent lamp or any other strong light shines on batteries. Do not try to recharge batteries; they are not intended to be recharged.
SELECTING INPUT SIGNAL Watching AV program This TV set provides AV input terminals for your convenient connection to VCR, or other video equipments. To watch video program from AV inputs, press TV/AV button repeatedly until you see the appropriate input indicator on the screen. TV AV1 Notes: AV1: Select AV1 when viewing the signals from the video equipment connected to the AV1 IN terminals. AV2: Select AV2 when viewing the signals S-Video AV2 from the video equipment connected to the AV 2 IN terminals.
1. Press MENU button repeatedly to display Search menu. 2. Press CH- or CH+ to select Channel menu item. 3. Press V- or V+ to select the unwanted channel. 4. Press CH- or CH+ to select Skip. 5. Press V- or V+ to select Skip ON. Thus, after exiting the menu, the channel will then be skipped when you select programs with the Channel up/down button. If you want to skip other unwanted channels, repeat steps above to change the channel number.
Use DSP button to know the current channel number Press DSP button to display the current TV state. If in TV program 12 ST SAP viewing, then it will display the current channel number, sound mode and remaining sleep time (if set). To scan programs Press SCAN button, the TV set will scan the channels from current channel to higher channels one by one, every program will be displayed for about one second and then go on scanning. Press SCAN button again, the screen will settle at the current scanned channel.
SOUND CONTROLS Adjusting Volume 1. 2. Use Volume up/down button Press V- button, the volume decreases; Press V+ button, the volume increases. Make use of Sound menu to adjust volume Press MENU twice to display Sound menu, then make use of V+/-button to adjust the level. 3. 4. Use MUTE button Press MUTE button on the remote control to cut off the sound from TV. To resume the sound, press this button again. TIMER SETTING Setting clock time Making use of this function can set the current time for the TV.
Setting sleep timer Making use of the Sleep timer function allows you to have the set automatically turn off after a preset time. For example, if you would like the TV to auto turn off in 60 minutes, you can press button repeatedly until the screen displays the desired amount of time. If you want to cancel the sleep timer, you can press button repeatedly until 0 displays on the screen.
SPECIFICATIONS Television System: NTSC/M Receiving channel: 181 channel tuner (Frequency synthesized tuning) Audio output: Audio output mode: Antenna impedance: 2 speakers of 3W each RF-MONO, A/V STEREO 75 ohm terminal Output terminal: Video input 1vp-p/75 Ohm, audio input 400mV Closed caption: NTSC/M receiving time (cc1-cc4/tt1-tt4) OSD Language: Power: Measurements (Length Width Height): Net Weight: Accessories: English/French AC 90-130V, 50/60 Hz 20" – 600 x 482 x 445 (mm) 24" – 710 x 485 x 51
