Specification

TILING 09 30 00 Surface Prep / TDS-102
EasyMat®canbebondedwithaCustom®polymermodifiedmortar
meeting ANSI A118.4, A118.15 or A118.11. Apply with a 3/16" x 1/4"
(5 x 6 mm) V-notch trowel for 3 mm and 5 mm or use a 1/4" x 1/4" x
1/4" (6 x 6 x 6 mm) square-notch trowel for 12 mm. Apply only
enoughmortarascanbecoveredwithEasyMat®within2030
minutes.Asasecondalternative,OmniGrip®MaximumStrength
AdhesiveorReliaBond®CeramicTileAdhesivecanbeusedtobond
EasyMat®tothesubstrateindryareas.
EmbedEasyMat®insidefacedown(againstthecurloftheroll),into
the wet bonding material. Do not allow the material to flop into place,
as this may cause air entrapment. Immediately roll the mat using a 30-
50 lb (13-26 kg) roller for 3 mm and 5 mm and a 100 lb (45 kg) roller
for 12 mm. Or use a hand roller applying 30 - 50 lbs (13-26 kg) of
pressure for 3 mm and 5 mm mats and 100 lbs (45 kg) of pressure for
the 12 mm mat to ensure proper adhesive transfer. Overlap each roll
of the roller 50% of the previous pass. Roll the width first, then the
length. Fold the second half of the roll back over the first half of the
material. Spread the adhesive at right angles to the seams in order to
prevent the adhesive from oozing up through the seam. Ensure the
lengthwise edge of the material is aligned exactly with the neighboring
section. Edges must contact but not overlap.
For the 12 mm, as with all thicker-rolled soft-flooring products, back-
curling/lifting may occur at the ends. Once laid out and in position,
seams and ends may need to be weighted (a few inches in) with a
short board, straightedge, or tile until the mortar takes set. Repeat
procedureforthenextsectionofEasyMat®.Youcanbegintoinstall
tileimmediatelyafterinstallationofEasyMat®iscomplete,provided
that full coverage with the thin-set bond coat has been attained
betweenthesubstrate(plywoodorOSB)andEasyMat®,andthat
steps are taken to ensure the bond between the substrate and
EasyMat®isnotbrokenasthetileisset.
Basic Peel & Stick Application
FirstapplyCustom's®Peel&StickPrimerwithapaintbrush,short
nap roller, or a soft-push broom. Apply an even coat (5-10 mils) and
allow to dry until tacky to the touch, about 30-45 minutes. When the
primer does not transfer to your finger, the surface is ready for
application. Unroll the mat while the release sheet is still attached,
position it over the area to be treated, and cut to appropriate length.
Roll up half of the cut mat leaving the other half still in position. Cut
release sheet from the rolled-up portion and pull it towards you
exposing and unrolling the self-stick portion of the mat. Reroll the
unrolled portion of the mat and follow the same procedure.
Immediately roll the mat using a 30-50 lbs (13-26 kg) roller, or use a
hand roller, applying 30-50 lbs (13-26 kg) of pressure, to ensure
proper adhesive transfer. Air pockets and wrinkles should be slit and
smoothed with a roller or the flat side of a trowel. Align subsequent
sheets and butt-join the seams tightly but do not overlap them.
Sound Control Application
Beforeapplication,firstcut3"(7.6cm)widestripsofEasyMat®and
bond them (using a bonding material above) to the wall perimeter of
the entire subfloor, as well as around the perimeter of any protrusions,
in order to isolate or break the vibration transmission path between
the floor and the wall. Assume that the walls you are butting up
against are not square. Using a chalk line, create a starting point for
an edge of the material to follow. Trim the ends of each section to
exact dimensions to fit the surface area to be covered (e.g., joints with
walls, etc.).
Installation of Baseboard/Cove base
If a cove base or baseboard is required, install it after the finished
floor has been installed. After the finished floor is installed, trim the
excess perimeter-isolation strip around the entire perimeter of the
finished floor. Nail the cove base or baseboard to the wall above the
perimeter-isolation strip. To isolate or break the vibration transmission
path between floor and wall, the baseboard must not touch the
finished floor. Adhere the cover to the wall above the finished floor.
Toe gap between the floor and the cover must be caulked, not
grouted. Grout will allow vibration to flank through the walls.
For a Waterproofing System
WaterproofsubfloorusingRedGard®WaterproofingandCrack
Prevention Membrane as per package instructions. Then bond
EasyMat®tosubflooraspergeneralapplicationinstructions.
Alternate Usage
Floating Floor Systems (Laminate or Engineered Wood):
EasyMat®isapprovedforuseunderfloatingfloorsystems.Follow
instructionsaboveforbondingEasyMat®tosubfloor,thenfollowfloor
manufacturer’sinstructionsforinstallationofthefloor.
Hardwood
EasyMat®isapprovedforuseunderhardwoodfloorsystems.After
bondingEasyMat®tothesubfloor(seebasicinstructions):
1) Consult with the wood adhesive manufacturer for compatibility with
EasyMat®.
or
2)Applyafull,minimum1/16"(1.6mm)skimcoatofeitherCustom’s
SkimCoat&PatchorSpeedFinish™Patching&FinishingCompoundto
the top. Allow the skim coat to cure, then bond the hardwood to the
cementitioussurfacefollowingmanufacturer’sinstructions.
Protection
If tile or stone will not be set immediately after curing, protect the
application from rain, direct sunlight and inclement weather for 72
hours after application. If delays longer than 72 hours are expected,
cover the area with felt paper. Care should be taken to prevent the
application from becoming soiled or punctured during and after
application.
Tile and Stone Installation
InstalltileorstonewithaCustom®BuildingProductspolymer
modified mortar that meets ANSI A118.4, A118.15 or A118.11
standards.
Cleaning of equipment
Clean tools and hands with water before the material dries. Clean all
spray equipment immediately after use.
Health Precautions
Wear rubber gloves and eye protection while using this product. Avoid
eye contact or prolonged contact with skin and wash thoroughly after
handling. If eye contact occurs, flush with water for 15 minutes and
consult a physician. Wash thoroughly after handling. Do not take
internally. Keep out of the reach of children.
EasyMat®Tile&StoneUnderlayment
Published Date: 11/13/2013